Select Hobbies SkiniWag build thread
#26
Senior Member
Thread Starter
Join Date: Jan 2003
Location: BARNWELL,
SC
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Next I bent the landing gear wire best I could to the shape on the plan and assembled the box it fits in. Then I glued it and the forward brace for it into the fuselage.
#29
Senior Member
Thread Starter
Join Date: Jan 2003
Location: BARNWELL,
SC
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Next I glued in the 9 gram servos. I installed an AR 6110 end pin Rx and BEC in the area in front of the servos. The 2S LiPo will go in ahead of the landing gear. Then I glued on the bottom wing.
#30
Senior Member
Thread Starter
Join Date: Jan 2003
Location: BARNWELL,
SC
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Glue the R2 ribs in line with the fuselage sides. Cap the wing and fuselage bottom with the 1/16" X 3/4" balsa. I'm leaving the front open for now and will make a hatch for battery access. Trim the bottom sheeting to the fuselage sides and hinge the tail surfaces.
#32
Junior Member
Join Date: Jan 2003
Location: Mammoth Spring,
AR
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Mine is almost under powered with a PAW .03 but yours is going to be a rocket with the Tee Dee. You might ought to put the throttle on it before flying. I have a few extra throttle sleeves so if you need one just let me know.
#33
Senior Member
Thread Starter
Join Date: Jan 2003
Location: BARNWELL,
SC
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Thanks George! I have one on hand if I need it.
#40
Senior Member
Thread Starter
Join Date: Jan 2003
Location: BARNWELL,
SC
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
#43
Junior Member
Join Date: Jan 2003
Location: Mammoth Spring,
AR
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
Looks great Hollis. Mine weighs just over 10 ounces with a throttled PAW .03. It flies great. Plenty of power but not enough to get in trouble. Thank Goodness!
#47
Senior Member
Thread Starter
Join Date: Jan 2003
Location: BARNWELL,
SC
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the compliments guys. That particular TD is no ball of fire; compression is a little low. I may swap out the cylinder and piston assembly.
Pond Skipper, That prop is marked 6X3, but I always experiment with different props to find one that best suits the plane. I know the bipe is going to want thrust rather than speed.
Pond Skipper, That prop is marked 6X3, but I always experiment with different props to find one that best suits the plane. I know the bipe is going to want thrust rather than speed.
#49
Senior Member
Thread Starter
Join Date: Jan 2003
Location: BARNWELL,
SC
Posts: 990
Likes: 0
Received 0 Likes
on
0 Posts
Uploading video to youtube, will post it soon. Best watched full screen and HD.
https://www.youtube.com/watch?v=Vr245ZhFq-k&feature=em-upload_owner#action=share
https://www.youtube.com/watch?v=Vr245ZhFq-k&feature=em-upload_owner#action=share
Last edited by hfenn; 05-11-2015 at 06:15 PM.