dle 30 prop data
i am throwing a 19x10 prop on my new dle 30 is that ok do i have to change it
|
RE: dle 30 prop data
I use a 19x8 Mejzlik carbon fibre prop on my 30cc aerobatic and its fine. What sort of plane are you putting the engine in?
|
RE: dle 30 prop data
ive used 18x8 Xoar BW, 18X10 Mejzlik, 19x8 Xoar BW and a 19x6 XoarBW..... so far on my 1/4 scale Cub i like the 19x6 best,i get the best pull out out of a hover..
i managed to get 8k out of the 19x6, i never tached the other props If i were to have a DLE30 n a light dedicated 3D/aerobatic plane, i would use a 19x8 |
RE: dle 30 prop data
I have 1/2 gallon through mine with a Vess 19b. I won't try anything else. Bought a Xoar 18x8 that I inended to use for break in, but I'll probably skip that process and run the snot out of it. Pulls a 10lb 3DHS Slick very well
|
RE: dle 30 prop data
I have a 3DHS 71 Slick with a DLE 30 and I use XOAR 20x6 and it is great. CLocked at 96 mph and hovers with great pullout. I have over 4 gallons through this motor and it keeps getting better.
|
RE: dle 30 prop data
ORIGINAL: octanehuffer I have 1/2 gallon through mine with a Vess 19b. I won't try anything else. Bought a Xoar 18x8 that I inended to use for break in, but I'll probably skip that process and run the snot out of it. Pulls a 10lb 3DHS Slick very well Huffer, why not a 20A on that AJ slick? Wouldnt that be better yet than the 19B? |
RE: dle 30 prop data
ORIGINAL: Stratos268 I have a 3DHS 71 Slick with a DLE 30 and I use XOAR 20x6 and it is great. CLocked at 96 mph and hovers with great pullout. I have over 4 gallons through this motor and it keeps getting better. Stratos, I have mine on the bench, 50% complete same setup I am going with. Do you know what the overall weight you are running? I weighed mine with partially completed and threw all the servos tank and spinner prop and hardware I am installing in the cavity and it weighs over 11 pounds already and I am going to load it up with some reinforcing glue and braces too. Don't know how guys can claim 10 pounds on this plane, don't see it happening....11 pounds best case. |
RE: dle 30 prop data
I really am not sure of the weight of the slick. I never weighed it. I did have a 3dhs 72 extra that weighed 10.2 with the same setup as my 71 slick. The slick is a little bigger than the extra so my slick probably is close to 11lbs also.
|
RE: dle 30 prop data
I'm using an APC 18/6W on a single bolt conversion. Static thrust is 20 lbs at 8900 rpm.
She's a screamer |
RE: dle 30 prop data
Got the hobbyking orange yak, weight is 10 pounds 8 oz dry, lighter than my pilot yak was but also very slightly smaller at 71 inch span, flys lighter. Fly it with the hobbyking 3d 19 8 prop, hover 1/4 throttle with dle 30 v2. lovely.
|
RE: dle 30 prop data
Vess 19B
|
RE: dle 30 prop data
dear friends I know from threads and forum you prefer XOAR, meijzik, MAS but especcially I want to know your experiences about these props..is there any difference regarding performanc3 .<div>
</div> |
All times are GMT -8. The time now is 09:44 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.