Go Back  RCU Forums > RC Airplanes > ARF or RTF
Reload this Page >

BH Twister

Notices
ARF or RTF Discuss ARF (Almost Ready to Fly) radio control airplanes here.

BH Twister

Old 08-05-2012, 02:43 PM
  #1  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default BH Twister

This is another defunct RTA airplane that I couldn't pass up from Hobby People. I believe it was on sale at the time & at a price I couldn't resist. It is of conventional design, shoulder wing, constant chord, tail dragger, with approx 540 sq. in. of wing area for a .35 to .45 size 2-stroke and is built in Vietnam. Upon initial inspection, the bump that represents a canopy has to go. The main gear is too far forward and in my opinion, has to move back behind the leading edge rather than where the mfg located it fwd of the LE. The "pinned" piano-style hinges also bother me particularly since it looks like hot-melt glue was used to install them.
Attached Thumbnails Click image for larger version

Name:	Qo40603.jpg
Views:	64
Size:	122.1 KB
ID:	1789436   Click image for larger version

Name:	Bw72584.jpg
Views:	56
Size:	127.2 KB
ID:	1789437   Click image for larger version

Name:	Rw57993.jpg
Views:	55
Size:	27.7 KB
ID:	1789438  
Old 08-05-2012, 02:54 PM
  #2  
Neo gold
Senior Member
 
Neo gold's Avatar
 
Join Date: Mar 2010
Location: Leeds, UNITED KINGDOM
Posts: 194
Likes: 0
Received 0 Likes on 0 Posts
Default RE: BH Twister

Ah, i remember my old twister!....had bags of fun with this & i had an OS 46AX initially..then upped it to an AX55 ...silly thing to do!, flew the wings off this for a few seasons until i got a little daft & plowed it into the ground 'from an unrecoverable flat spin'.....i had no problems with the hinged & pinned controls surfaces at all...
This will do most manouvers with the utmost ease...you can take off & land this with your eyes closed...honest!, you'll get super~over confident with it...enjoy.
Marc.
Old 08-05-2012, 03:18 PM
  #3  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default RE: BH Twister


ORIGINAL: Neo gold

Ah, i remember my old twister!....had bags of fun with this & i had an OS 46AX initially..then upped it to an AX55 ...silly thing to do!, flew the wings off this for a few seasons until i got a little daft & plowed it into the ground 'from an unrecoverable flat spin'.....i had no problems with the hinged & pinned controls surfaces at all...
This will do most manouvers with the utmost ease...you can take off & land this with your eyes closed...honest!, you'll get super~over confident with it...enjoy.
Marc.
Good to know; thanks for dispelling any concern over the hinges. I hope I have as much fun with it as you had.
Old 08-05-2012, 04:00 PM
  #4  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default RE: BH Twister

The cowling was way too thin and damaged with chipped paint missing so I decided to add thickness. Because epoxy doesn't seem to do well over polyester and my old K&B resin looked like Jello, I decided to buy a quart at the local auto parts store. I wet sanded the paint off the cowl, cut patterns from stiff paper, cut lft, rt, top, and bottom pieces of 6 oz glass and applied them to the inside of the cowling to triple the thickness...
Attached Thumbnails Click image for larger version

Name:	Ca81294.jpg
Views:	153
Size:	106.7 KB
ID:	1789465   Click image for larger version

Name:	Dy79624.jpg
Views:	50
Size:	98.7 KB
ID:	1789466   Click image for larger version

Name:	Qv53552.jpg
Views:	51
Size:	95.6 KB
ID:	1789467   Click image for larger version

Name:	Oh13789.jpg
Views:	52
Size:	87.0 KB
ID:	1789468   Click image for larger version

Name:	Tr50500.jpg
Views:	52
Size:	113.1 KB
ID:	1789469  
Old 08-06-2012, 11:28 AM
  #5  
Texastbird
 
Texastbird's Avatar
 
Join Date: Jul 2002
Location: La Porte, TX
Posts: 1,217
Likes: 0
Received 2 Likes on 2 Posts
Default RE: BH Twister

Ok, so I'm dumb. What's RTA?
Old 08-06-2012, 04:21 PM
  #6  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default RE: BH Twister


ORIGINAL: Texastbird

What's RTA?
Ready-To-Assemble.
Old 11-10-2017, 04:04 PM
  #7  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Some other things I don't like include color scheme, number of hinges, hinge gap, a spinner that's not yellow, and control surfaces without enough thickness taper. I decided after all to begin removing the hinges with the assistance of heat and lots of pulling...
Attached Thumbnails Click image for larger version

Name:	IMG_2085.JPG
Views:	47
Size:	1.08 MB
ID:	2244359   Click image for larger version

Name:	IMG_1771.JPG
Views:	44
Size:	951.9 KB
ID:	2244360   Click image for larger version

Name:	IMG_1773.JPG
Views:	48
Size:	1.26 MB
ID:	2244361   Click image for larger version

Name:	IMG_2091.JPG
Views:	41
Size:	1.02 MB
ID:	2244362   Click image for larger version

Name:	IMG_2092.JPG
Views:	48
Size:	1.14 MB
ID:	2244363   Click image for larger version

Name:	IMG_2087.JPG
Views:	49
Size:	1.18 MB
ID:	2244369  

Last edited by H5606; 11-11-2017 at 08:58 AM.
Old 11-11-2017, 09:47 AM
  #8  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Good practice here harvesting the covering material and hinges for use down the road on similar or smaller-sized airplanes so that when in post-apocalyptic world will have developed these skills already. Uncovering elevators, horizontal stab, vertical stab, and rudder. The existing hinge slots are wide enough to drive a tank through. Used partially installed screws to hammer out the blind nuts on the gear plate in the fuselage and took off the canopy blister.
Attached Thumbnails Click image for larger version

Name:	IMG_2088.JPG
Views:	44
Size:	1.37 MB
ID:	2244514   Click image for larger version

Name:	IMG_2090.JPG
Views:	50
Size:	1.62 MB
ID:	2244515   Click image for larger version

Name:	IMG_2093.JPG
Views:	40
Size:	1.72 MB
ID:	2244516   Click image for larger version

Name:	IMG_3562.JPG
Views:	45
Size:	1.08 MB
ID:	2244517   Click image for larger version

Name:	IMG_3563.JPG
Views:	45
Size:	1.48 MB
ID:	2244520   Click image for larger version

Name:	IMG_3564.JPG
Views:	41
Size:	1.47 MB
ID:	2244521   Click image for larger version

Name:	IMG_3566.JPG
Views:	46
Size:	1.04 MB
ID:	2244522   Click image for larger version

Name:	IMG_3568.JPG
Views:	47
Size:	1.66 MB
ID:	2244523  

Click image for larger version

Name:	IMG_3569.JPG
Views:	42
Size:	1.28 MB
ID:	2244524  

Last edited by H5606; 11-11-2017 at 10:15 AM.
Old 11-11-2017, 10:34 AM
  #9  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Cleared covering from fuselage and over-wing hatch. There's no instructions in the owner's manual about covering removal so you're on your own here. Getting better at uncovering now - reversed the mfg's covering process which was covering top and bottom first, then sides. Naked fuse feels heavy and weighs 9 and 5/8 oz. Just for fun, checked covering removed is 3/4 oz.
Attached Thumbnails Click image for larger version

Name:	IMG_3570.JPG
Views:	42
Size:	921.7 KB
ID:	2244532   Click image for larger version

Name:	IMG_3571.JPG
Views:	42
Size:	921.2 KB
ID:	2244533   Click image for larger version

Name:	IMG_3573.JPG
Views:	40
Size:	1.31 MB
ID:	2244534   Click image for larger version

Name:	IMG_3574.JPG
Views:	40
Size:	1.55 MB
ID:	2244535   Click image for larger version

Name:	IMG_3576.JPG
Views:	40
Size:	1.27 MB
ID:	2244536   Click image for larger version

Name:	IMG_3577.JPG
Views:	45
Size:	1.04 MB
ID:	2244537   Click image for larger version

Name:	IMG_3578.JPG
Views:	41
Size:	1.29 MB
ID:	2244538   Click image for larger version

Name:	IMG_3579.JPG
Views:	40
Size:	1.35 MB
ID:	2244539  


Last edited by H5606; 11-11-2017 at 10:47 AM.
Old 01-28-2018, 03:34 PM
  #10  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Used heat to facilitate removal of the main-gear mounting plate; if it is actually hot-melt glue, it only becomes gummy under the heat gun but will let go under significant leverage.
Ran bolts thru fender washers to spread out the load on the gear plate and clamped on Vice-grip pliers to give a handle to pry on - prying it out lifted the adjacent bottom sheeting.

Partially installed landing gear screws and some spacers under plate allow quick removal of the blind nuts using light tapping.

Removed forward bottom sheeting and used additional heat with chisel to remove gear doublers from fuselage sides; there is no fuel proofing in this area so will now have better access to do so.
Attached Thumbnails Click image for larger version

Name:	IMG_3593.JPG
Views:	38
Size:	924.7 KB
ID:	2252488   Click image for larger version

Name:	IMG_3594.JPG
Views:	37
Size:	1.68 MB
ID:	2252489   Click image for larger version

Name:	IMG_3596.JPG
Views:	37
Size:	1.30 MB
ID:	2252490   Click image for larger version

Name:	IMG_3597.JPG
Views:	38
Size:	1.20 MB
ID:	2252491   Click image for larger version

Name:	IMG_3598.JPG
Views:	40
Size:	1.50 MB
ID:	2252492  
Old 02-04-2018, 02:48 PM
  #11  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Continuing somewhat destructive de-construction; removed top sheeting of fuse from LE of wing aft. Used punch to remove hatch latch. Tried heat on sheeting but ended up using brute force, a planer, and aggressive sanding tools. Looking to deepen fuselage by an inch and a half or so to make it TLAR. Wood is strange - very brittle - think they call this Luan.

Also began pulling off ailerons and uncovering wing panel.
Attached Thumbnails Click image for larger version

Name:	IMG_3599.JPG
Views:	39
Size:	1.23 MB
ID:	2253470   Click image for larger version

Name:	IMG_3601.JPG
Views:	38
Size:	1.67 MB
ID:	2253471   Click image for larger version

Name:	IMG_3600.JPG
Views:	182
Size:	1.25 MB
ID:	2253472   Click image for larger version

Name:	IMG_3603.JPG
Views:	38
Size:	1.17 MB
ID:	2253473   Click image for larger version

Name:	IMG_3580.JPG
Views:	34
Size:	1.04 MB
ID:	2253474   Click image for larger version

Name:	IMG_3581.JPG
Views:	34
Size:	1.00 MB
ID:	2253475   Click image for larger version

Name:	IMG_3604.JPG
Views:	39
Size:	1.40 MB
ID:	2253476   Click image for larger version

Name:	IMG_3606.JPG
Views:	38
Size:	1.30 MB
ID:	2253477  

Old 02-04-2018, 02:56 PM
  #12  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Heat is used where necessary to loosen stubborn areas while pulling off covering.
Attached Thumbnails Click image for larger version

Name:	IMG_3608.JPG
Views:	34
Size:	1.06 MB
ID:	2253478   Click image for larger version

Name:	IMG_3610.JPG
Views:	34
Size:	1.02 MB
ID:	2253479   Click image for larger version

Name:	IMG_3611.JPG
Views:	31
Size:	949.8 KB
ID:	2253480   Click image for larger version

Name:	IMG_3613.JPG
Views:	34
Size:	1.21 MB
ID:	2253481   Click image for larger version

Name:	IMG_3615.JPG
Views:	36
Size:	1.19 MB
ID:	2253482   Click image for larger version

Name:	IMG_3616.JPG
Views:	36
Size:	1.19 MB
ID:	2253483   Click image for larger version

Name:	IMG_3617.JPG
Views:	37
Size:	1.21 MB
ID:	2253484   Click image for larger version

Name:	IMG_3618.JPG
Views:	38
Size:	1.26 MB
ID:	2253485  

Old 02-25-2018, 06:07 PM
  #13  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Continued covering removal - now similar treatment to left wing panel. Being Oracover/Ultracoat it's fairly easy to remove.

Closeup of an outboard rib shows one that looks like a warped noodle the mfg is willing to pass as acceptable for general populace.

Began modifying existing construction by adding additional trusses (and weight, of course) to horizontal flying surface - inboard next to center section - looked like it had way too much unsupported area...
Attached Thumbnails Click image for larger version

Name:	IMG_3621.JPG
Views:	35
Size:	1.06 MB
ID:	2256097   Click image for larger version

Name:	IMG_3622.JPG
Views:	167
Size:	1.29 MB
ID:	2256098   Click image for larger version

Name:	IMG_3623.JPG
Views:	32
Size:	1.22 MB
ID:	2256099   Click image for larger version

Name:	IMG_3624.JPG
Views:	34
Size:	1.13 MB
ID:	2256100   Click image for larger version

Name:	IMG_3627.JPG
Views:	42
Size:	1.06 MB
ID:	2256101   Click image for larger version

Name:	IMG_3628.JPG
Views:	34
Size:	1.22 MB
ID:	2256102   Click image for larger version

Name:	IMG_3629.JPG
Views:	37
Size:	1.26 MB
ID:	2256103   Click image for larger version

Name:	IMG_3630.JPG
Views:	33
Size:	1.17 MB
ID:	2256104  

Click image for larger version

Name:	IMG_3631.JPG
Views:	39
Size:	1.27 MB
ID:	2256105   Click image for larger version

Name:	IMG_3638.JPG
Views:	34
Size:	932.6 KB
ID:	2256106   Click image for larger version

Name:	IMG_3639.JPG
Views:	35
Size:	1.03 MB
ID:	2256113   Click image for larger version

Name:	IMG_3640.JPG
Views:	33
Size:	1.01 MB
ID:	2256114  

Last edited by H5606; 02-25-2018 at 06:09 PM.
Old 01-20-2019, 05:02 PM
  #14  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Finished covering removal from the airframe.

Ailerons shown here as covering removal begins. Experienced eureka moment - the strip ailerons are not solid wood - they're actually built-up structures! Additional pics show ailerons bare with covering removed; note the factory "X" pen marks - perhaps used to denote the bottoms of both ailerons...

Second to last pic shows all the covering from the airframe that was salvaged to cover other projects down the road or can be used to cover another BH Twister.

Last pic shows pristine spinner, hinges, and canopy salvaged from this airplane that can be used to support other projects in the future.












Last edited by H5606; 01-21-2019 at 04:56 PM.
Old 01-21-2019, 04:47 PM
  #15  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Starting with the addition of 1.5" to the top of the apex (former at the wing TE), a line connecting the apex to the existing tail block defines the top of the additions for the other formers. Accounting for skin thickness offset, cut these formers from scrap 1/8" lite-ply and removed mat'l from the centers.

Bonded these former extensions to the tops of the formers including one on the top of the over-wing hatch fairing to support sheeting at center point. Cut and installed 1/16" sheeting to aft fuselage top.

Debated about the area fwd of the apex, thinking about simplicity of straight line to remain "Hots-like" or introducing complexity with a curve. Decided to create curve with the intention of gaining even more area over wing and hopefully supporting knife-edge flight.

Last pic shows dry fit of fwd area sheeting with canopy-like curve to center section hatch to judge general outline.
















Last edited by H5606; 01-21-2019 at 05:07 PM.
Old 01-27-2019, 05:56 PM
  #16  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Took measurements of fore and aft areas for new, repositioned gear plate. Transferred measurements to scrap 1/4" ply and fabricated new gear mounting plate. Drew center lines.

Positioned L&R gear legs over center-line showing mfg's skewed butt joint. Sanded butt joint to true, and marked/center-punched gear plate for blind nuts resulting in slightly narrower gear-track.

Drilled gear plate for blind nut installation. Sanded blind nut flanges for overlap clearance at center point and added to gear plate.

















Old 01-28-2019, 05:48 AM
  #17  
Appowner
Banned
 
Join Date: Nov 2017
Posts: 1,016
Likes: 0
Received 3 Likes on 3 Posts
Default

2012 to 2019 for an ARF? You're slower than I am!
Old 01-28-2019, 02:16 PM
  #18  
H5606
Thread Starter
 
Join Date: Jul 2006
Location: TN
Posts: 924
Received 41 Likes on 40 Posts
Default

Yeah, and its still not done. How is it that ARF's are for modelers that don't have the time to spend building?

Ends up being an exercise in wasting part of yer life away; very difficult to stay focused on it when there's more rewarding stuff around to build or fly.

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.