Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Page 17 of 18 FirstFirst ... 715161718 LastLast
Results 401 to 425 of 437

  1. #401
    grosbeak's Avatar
    Join Date
    Dec 2010
    Location
    Ottawa, ON, CANADA
    Posts
    927
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Hey Stokey,

    It's still slightly nose heavy. My gas tank is pretty close to the CG - how about yours? I know on a lot of planes they're forward of the CG. Those, if I understand correctly, should be balanced with an empty tank, just a little heavy on the nose.
    MAAC 83386
    Stetson Flyers, Ottawa
    G-RSBK

  2. #402

    Join Date
    Sep 2002
    Location
    BASIN, WY
    Posts
    26
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Thanks grosbeak for the comeback. sounds like we are kinda on the same page. My Pulse 60 with the Saito 100 came out just a little tail heavy. I think because i purchased a Turbo Header Muffler from RC Specialties and it is not as heavy as the Saito Muffler. I ended up adding about 4oz. on the firewall just under the motor mount to get it just a touch nose heavy with an empty fuel tank. I also never did like balancing a plane on dowel sticks under the wing, so on all of my planes I find the CG and run a small piece of control tubing through the plane from the bottom to the top. That way I can hang it on a string. (heavy fishing line) and check the balance fwd and aft and also the lateral balance. I've always had very good luck doing it that way. I post some pics in a few days.

    Another problem I need to fix on the ARF Pulse is the wing and the horizontal stab are not on the same plane. I need to take the rear stab off and cut or sand one side of the fuse to get one side of the stab lower so to be on the same plane as the wing. If I cannot get it corrected I may contact Hanger 9 or Horizon and see if they will replace the fuse. I hate to have to do that though because of all the time I have invested in just getting it this far towards the first test flight. How much will it effect the flying of the plane if the wing and the hor stab are not in a straight line or parallel with each other when when viewed from the front or rear of the aircraft??

    Stokey

  3. #403
    grosbeak's Avatar
    Join Date
    Dec 2010
    Location
    Ottawa, ON, CANADA
    Posts
    927
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*


    Looking forward to seeing pics of your balancing method.

    ORIGINAL: STOKEY

    Another problem I need to fix on the ARF Pulse is the wing and the horizontal stab are not on the same plane. I need to take the rear stab off and cut or sand one side of the fuse to get one side of the stab lower so to be on the same plane as the wing. If I cannot get it corrected I may contact Hanger 9 or Horizon and see if they will replace the fuse. I hate to have to do that though because of all the time I have invested in just getting it this far towards the first test flight. How much will it effect the flying of the plane if the wing and the hor stab are not in a straight line or parallel with each other when when viewed from the front or rear of the aircraft??

    Stokey
    I'm no expert but it can't be a good thing - at the very least I expect it wouldn't climb or descend in a straight line. Here are a couple of simple diagrams - for the sake of the discussion let's assume everything else about the airplane is perfectly balanced and trimmed.

    Wing and horizontal stabilizer in the same plane:



    With up elevator, the plane pitches straight up.


    Wing and horizontal stabilizer not in the same plane:



    With up elevator the plane still pitches up but there is some degree of ruddering, causing the plane to yaw towards the lower side of the horizontal stabilizer.


    I'm using reason here, not experience. I hope someone with more of the former and/or the latter will chime in. If not, there may be a better forum topic for this question, like Questions and Answers.
    MAAC 83386
    Stetson Flyers, Ottawa
    G-RSBK

  4. #404

    Join Date
    Jun 2007
    Location
    Freedom, PA
    Posts
    544
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    I lost a elevator servo on my Pluse 60-resulted in a crash that riped out the L/G and broke the fusalage in half behind the wing saddle. When I glued her back together the fuss had a slight twist resulting in the same problem. Since the tail is bolt on, I shimmed the low side aprox 1/32 until the horizontal stab was level. Easy Fix.

  5. #405

    Join Date
    Sep 2002
    Location
    BASIN, WY
    Posts
    26
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Thank you for the input Guys!
    I was thinking along the same lines, but wanted to get some other ideas. A friend and myself were looking at the plane the other night and both thought that shimming the tail section would be the easiest fix, although reluctant to do that without asking some questions first. I'll probably give that a try this evening after finishing up the "honey-do" chores today. Have a great Day and thanks again for your thoughts.
    stokey

  6. #406

    Join Date
    Jun 2007
    Location
    Freedom, PA
    Posts
    544
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    You might also try twisting the fuss in the direction need'ed to level the stab, and re-shrink the covering that loosens, to hold it in place. A helper would be benaficial. Use a shim to correct the last bit of miss-allighment. I'd say you'll be fine & wont even be noticeable when the plane is done.

  7. #407

    Join Date
    Jan 2010
    Location
    Winston-Salem, NC
    Posts
    33
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    I have been following this post with interest. (Ever since my first Pulse died an ugly death when the elevator broke loose.) Anyway's Horizon's free replacement with the new elevator has been great. I've been flying it for about a year now. This is only my third plane but have noticed something that I hadn't before.

    As the plane is flying level (1/2 throttle) and then when I hit the throttle the plane tends to pitch up slightly and rolls to the right. I have a Saito 115, 15x6 prop. The plane balances to spec but I would note this. Lateral balance is a bit off. If I put 1.5 grams of lead on the outermost part of the left wing (viewed from behind) it now balances level. Could this little amount of weight make that kind of difference? Or, is something else up? Viewing the plane there appears to be no warping etc. Thank you.

  8. #408

    Join Date
    Sep 2002
    Location
    BASIN, WY
    Posts
    26
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    While building my Pulse 60 I hung the plane from a string through the recommended balance point. I have a Saito 100 on it , so had to add about 3/4 to 1 oz. on the firewall to get the balance a touch nose heavy. When viewing from the rear, I noticed the left wing dipped about 1" , so plan to ad just enough weight to the right wing to bring to level lateral. sounds like this is the same problem as you are describing.
    Stokey

  9. #409
    tailskid's Avatar
    Join Date
    Nov 2001
    Location
    Tolleson, AZ
    Posts
    8,071
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Hey Brian...long time no hear from you and Pulse...it is still in one piece?

    Jerry
    # 93 in Club Saito; Carl Goldberg Ultimate Brotherhood # 12; Pulse brother # 2;Hellcat Brotherhood #8;P-47 Thunderbolt Brotherhood #18

  10. #410
    tailskid's Avatar
    Join Date
    Nov 2001
    Location
    Tolleson, AZ
    Posts
    8,071
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Put the DLE 20 in today with a Sullivan Mount and noticed I won't be able to get to the high/low speed adjustment needles - oh well, I'll just have to tinker with that later. Do have a question about the choke and throttle arrangements - how'd you guys link those up?

    Jerry
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	Mk27478.jpg 
Views:	33 
Size:	48.5 KB 
ID:	1771850   Click image for larger version. 

Name:	Yw68528.jpg 
Views:	35 
Size:	77.5 KB 
ID:	1771851  
    # 93 in Club Saito; Carl Goldberg Ultimate Brotherhood # 12; Pulse brother # 2;Hellcat Brotherhood #8;P-47 Thunderbolt Brotherhood #18

  11. #411
    tailskid's Avatar
    Join Date
    Nov 2001
    Location
    Tolleson, AZ
    Posts
    8,071
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Even got the engine centered......well almost. Too bad the cowl had to be cut up so badly for the muffler
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	Wu62013.jpg 
Views:	22 
Size:	35.6 KB 
ID:	1771878   Click image for larger version. 

Name:	Fa85186.jpg 
Views:	14 
Size:	54.5 KB 
ID:	1771879  
    # 93 in Club Saito; Carl Goldberg Ultimate Brotherhood # 12; Pulse brother # 2;Hellcat Brotherhood #8;P-47 Thunderbolt Brotherhood #18

  12. #412

    Join Date
    Feb 2005
    Location
    Philly, PA
    Posts
    63
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Well, you may have had to cut it a lot BUT it looks nice and tight !! (looks clean, very good)

  13. #413

    Join Date
    Aug 2008
    Location
    Waterford, Mi/Citrus Springs, Fl
    Posts
    2,662
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*


    ORIGINAL: tailskid

    Even got the engine centered......well almost. Too bad the cowl had to be cut up so badly for the muffler
    The rear exhaust Syssa has been around a while, but other 30cc manf.'s seem to be catching on to the fact there's a big demand for REAR EXHAUST OUTLETS!! Doesn't seem to be that big a deal regarding design or manufacturing on those, hopefully it won't take too long for the 20cc manf's to figure out the same thing? Then we won't have to hack up our cowls like this.

    Agree though, very nice job on the necessary evil! Actually, I saw one muffler exposed like this that had been painted to match, didn't look to bad at all! No clue how that would hold up after extended service though.

  14. #414
    grosbeak's Avatar
    Join Date
    Dec 2010
    Location
    Ottawa, ON, CANADA
    Posts
    927
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*


    ORIGINAL: tailskid

    Put the DLE 20 in today with a Sullivan Mount and noticed I won't be able to get to the high/low speed adjustment needles - oh well, I'll just have to tinker with that later. Do have a question about the choke and throttle arrangements - how'd you guys link those up?

    Jerry
    My throttle hookup uses Sullivan Gold-n-Rods and a Sullivan ball link:



    For the choke, I made a bell crank from spare parts:





    The lever exits out the bottom:



    I pull it out to close the choke and push it in to open.
    MAAC 83386
    Stetson Flyers, Ottawa
    G-RSBK

  15. #415
    tailskid's Avatar
    Join Date
    Nov 2001
    Location
    Tolleson, AZ
    Posts
    8,071
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Excellent idea! I tried to remove that throttle arm and replace it with the one shown....that puppy doesn't want to come lose!

    Thanks,

    Jerry
    # 93 in Club Saito; Carl Goldberg Ultimate Brotherhood # 12; Pulse brother # 2;Hellcat Brotherhood #8;P-47 Thunderbolt Brotherhood #18

  16. #416

    Join Date
    Dec 2001
    Location
    Tullahoma, TN
    Posts
    862
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Hi Jerry
    Yup just moving slower every day. My Pulse 125 is still an old rocket ship and I'm still enjoying it to the max. keeps my fun meter pegged when I take it out. I used the compact wrap around muffler and was able to cut much less of the cowl than you had to. I got no notice from this thread as I normally do. Take Care. Brian
    ORIGINAL: tailskid

    Even got the engine centered......well almost. Too bad the cowl had to be cut up so badly for the muffler
    Brian P. Smith Bismith2@hotmail.com
    AMA 1044 IMAA 21141 W4BPS <><

  17. #417
    tailskid's Avatar
    Join Date
    Nov 2001
    Location
    Tolleson, AZ
    Posts
    8,071
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Had some trouble with the throttle barrel (got it twisted when tightening the arm) but fixed it! Now back to re-installing the engine; mounting the electronic module and putting on the canopy

    Jerry
    # 93 in Club Saito; Carl Goldberg Ultimate Brotherhood # 12; Pulse brother # 2;Hellcat Brotherhood #8;P-47 Thunderbolt Brotherhood #18

  18. #418

    Join Date
    Dec 2001
    Location
    Tullahoma, TN
    Posts
    862
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*


    It still looks fine. Just let er' rip!! Brian

    ORIGINAL: tailskid

    Even got the engine centered......well almost. Too bad the cowl had to be cut up so badly for the muffler
    Brian P. Smith Bismith2@hotmail.com
    AMA 1044 IMAA 21141 W4BPS <><

  19. #419

    Join Date
    Jun 2002
    Location
    Wichita, KS
    Posts
    17
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    I acquired a Pulse 125 at the annual local RC club auction two years ago. It came from the estate of a deceased club member. He had it powered with a OS 120AX and standard issue muffler. It's been sitting on the shelf in "moth balls" until a couple weeks ago when I pulled it out and dusted it off and began readying it for flight. I choose to mount up a Saito 125, and installed a larger fuel tank. I swapped the standard wheels (had flat spots from sitting) with new Sullivan Skylites, and added a new Sig medium size tail wheel assembly. I changed out the battery with a Hobbico 1800mah LiFe battery, just behind the fuel tank. I rounded it out with a used 2 3/4" Tru Turn spinner.

    I expected to have to add a bit of weight to the front of the airplane when I balanced it, but... I didn't expect to need 12 ONCES of lead up near the firewall. The CG is supposed to be 3 11/16" aft of the leading edge of the wing. I've tried it right side up and inverted, doesn't make any difference, it's going to take at least 12 onces. Has anybody else run into this particular problem...? I'm going to move the battery farther forward, and I may install a 2100 mah battery to offset some of the lead. But still, this seems like I'm adding a lot of weight. Is this consistent with other folks experiences?

    Jerry Hicks

  20. #420

    Join Date
    Mar 2007
    Location
    Elmira, NY
    Posts
    1,185
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    ORIGINAL: Jerry Hicks

    I acquired a Pulse 125 at the annual local RC club auction two years ago. It came from the estate of a deceased club member. He had it powered with a OS 120AX and standard issue muffler. It's been sitting on the shelf in ''moth balls'' until a couple weeks ago when I pulled it out and dusted it off and began readying it for flight. I choose to mount up a Saito 125, and installed a larger fuel tank. I swapped the standard wheels (had flat spots from sitting) with new Sullivan Skylites, and added a new Sig medium size tail wheel assembly. I changed out the battery with a Hobbico 1800mah LiFe battery, just behind the fuel tank. I rounded it out with a used 2 3/4'' Tru Turn spinner.

    I expected to have to add a bit of weight to the front of the airplane when I balanced it, but... I didn't expect to need 12 ONCES of lead up near the firewall. The CG is supposed to be 3 11/16'' aft of the leading edge of the wing. I've tried it right side up and inverted, doesn't make any difference, it's going to take at least 12 onces. Has anybody else run into this particular problem...? I'm going to move the battery farther forward, and I may install a 2100 mah battery to offset some of the lead. But still, this seems like I'm adding a lot of weight. Is this consistent with other folks experiences?

    Jerry Hicks
    Hey Jerry the OS 120AX is a PEACH! for me for this model, concidering I also have a NIB Saito 125 on the bench. I added no weight to get the CG dialed in to spec's using the Hangar 9 aluminum engine mount. Only added 1/2 ounce to balance it laterally. I also have my battery (JR 2700mah) mounted just behind the fuel tank. Hmm ya 12ounce seems like much, if that much weight is needed you might want to try a better but heavier engine mount instead of the stock one. Like the Hangar 9 aluminum one I'm using, you might only have to add like 7 ounces, or maybe even that heavy $40 metal Sullivan engine mount which might put you right on. Just trying to give you somtin to bit on.

  21. #421
    tailskid's Avatar
    Join Date
    Nov 2001
    Location
    Tolleson, AZ
    Posts
    8,071
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Mine just balanced....DLE20 up front.....balanced at 3 15/16th....might have to move the RX battery up into the tank area with the ignition battery.

    Your thoughts?
    # 93 in Club Saito; Carl Goldberg Ultimate Brotherhood # 12; Pulse brother # 2;Hellcat Brotherhood #8;P-47 Thunderbolt Brotherhood #18

  22. #422

    Join Date
    Jun 2002
    Location
    Wichita, KS
    Posts
    17
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Thanks for the info, much appreciated. I just pulled the battery and the tank and I'm reinstalling them as far forward as I can in the forward compartment. That should help some. I used a Great Planes 120 size mount, it was a bit heavier than the Hangar 9 mount that it replaced. I'm guessing that the heavier Sig medium size tail wheel assembly is part of the problem. The Hangar 9 tailwheel arrangement is connected directly to the rudder....makes it hard on the rudder servo. This is a fairly stout aluminum leaf tailwheel, and it doesn't take much weight that far back to make a big difference on the balance....

  23. #423
    tailskid's Avatar
    Join Date
    Nov 2001
    Location
    Tolleson, AZ
    Posts
    8,071
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Exactly! The 'movement' from the CG to the rear of the plane is very long - and that makes for a smooth flying bird Keep us posted.

    Jerry
    # 93 in Club Saito; Carl Goldberg Ultimate Brotherhood # 12; Pulse brother # 2;Hellcat Brotherhood #8;P-47 Thunderbolt Brotherhood #18

  24. #424

    Join Date
    Mar 2007
    Location
    Elmira, NY
    Posts
    1,185
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Yes Jerry that tail wheel setup is the nemesis, well then that explains it. Well it looks like you'll have pile on some weight. Hmm I wonder what that Sullivan tail wheel setup weighs compared to the Sig?

  25. #425

    Join Date
    Sep 2003
    Location
    san antonio, TX
    Posts
    251
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: *Hangar 9 New Pulse 125*

    Thanks to this thread I've got this model coming. Horizon was out so I ended up ordering from Espirit Models. Hoping it's not the older version. I placed my first order from Troy built models. I thought they were willing to go the extra mile to discuss things before ordering. I'd like to know which muffler to use? TBM came up with a silencer for the stock muffler which they include with an engine purchase (new plug too) . There's a video on their site demonstrating it. What do I need to do for engine cooling? No spinner? Do I need to replace the main gear and tailwheel?

    Silencer

    http://www.troybuiltmodels.com/items...0SILENCER.html


Page 17 of 18 FirstFirst ... 715161718 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT -6. The time now is 12:37 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.