RE: Midwest Extra 300xs Build
1 Attachment(s)
I then squared up a 3/4"x3/4"x3/8" plywood block to fit snug in the rudder front block opening. I used 30 min epoxy to glue in place. Next I cut a 1/8"x1" plywood block to fit in place over the 3/8" block on both sides of the rudder front and glued them in place as well with 30 min epoxy. I then Clamped the blocks in place to dry overnight.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
After the blocks dried overnight, I sanded them flush with the cap strips on t7 and t8. Then I drew a straight line down the center of the leading edge (close enough) to begin shaping the bevel. I also marked a reference line on the end of the leading edge to act as a guide to shape to. Next, started shaping the bevel with a block plane to remove most of the balsa and rough sanding to the angle with a bar sander. In pic #3 you can see that all the bevel could not be shaped using the sander or the block plane, so I made a back cut with a razor saw and carved the remaining bevel tips out with a hobby knife. This is the same as when I did the elevator bevel. The end result came out pretty good.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
I then began rounding the trailing edge bottom corner, the trailing edge, and the leading edge on the counter balance. Also did some general sanding and flushing things up a little more. As you can see I will still need to do some more sanding before this piece is ready.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
Next I placed the rudder and the Vert/stab on the plan and marked the location on each for the hinge doubler blocks and glued them in. I also rounded the leading edge of the vert/stab.
After this is said and done, the rudder I mean, it dosn't appear my concerns of the thin trailing edge and the rib attachment were with any merit. The rudder seams to be pretty strong as built. I still think, however, that Midwest could have done a better job of laying out the sizes on the ribs in the rudder. |
RE: Midwest Extra 300xs Build
1 Attachment(s)
Finally got back to the shop, I had to break for a few days to fly, the weather has been fantastic.
Well I screwed up but "I think" I fixed it right. The first pics are of the horizontal stabs lined up on a straight line and you can see in the first pic that everything seem ok, but wait. The back side has a 1/16" to 1/8" gap. So what I did is took a piece of 1/8" balsa and epoxied an end cap on the stab. Then sanded the end with the proper angle to fill the gap solid. I must have missed the end rib moving while setting the first top spars on the assembly. This looked like the most obvious fix to me, can't think of another way to do this. Any way, after sanding the end cap to fit, they lined up well and no gap. Then pinned one side to the board making sure to center exactly on the line. I glued the two sides together with 30 min epoxy and clamped at the tip to let dry overnight. Next step will be to shape the leading edge and fill and sand the rest of the surface. Then I took another break to go flying. Be back soon. |
RE: Midwest Extra 300xs Build
That'll work !!! I'm going flying tooooo. ENJOY !!! RED
|
RE: Midwest Extra 300xs Build
Just to let everyone know, I will be back to the shop soon. I had some things to take care of around the house as well as taking advantage of the great flying weather to maiden my first build. I will pick up where I left off shaping the leading edge of the horizontal stab.
Bob |
RE: Midwest Extra 300xs Build
Well, just wanted to let everyone know that I am still building.My home PC crashed, (processor went bad) and I get to build another(AMD-64 3800), It's not worth replacing the processor, at least thats my story and I'm sticking to it.. I Will get back to posting when I am running again, hopefully by the end of next week.
|
RE: Midwest Extra 300xs Build
Hey there looks like your doing good so far . I just framed my extra 300 xs ,still need to fiberglass the wing joint and assemble the tail feathers to the fuse.Its a fast builder I think .Ok a few points to watch out for , if you haven't up graded your plans with the new addendum's supplied .for your sakes do it ,will save you some real probs later on .Oh before I forget this ,they show adding pins to the engine mount (wooden dowels ) but they don't show anything about doweling the landing gear plate .I added 2 per side to mine 1/8 !" dowels ,plus I also added some extra tri stock to the motor mount plate and box. Your right about the hardware its ok for a 60 -90 maybe???the tailwheel assy is really a joke all that will hold it in place is a hunk of fuel tubing Shakes my head I wouldn't trust this set up on a parkflyer *LOL*
As far as the 6-32 screws in the elevators coming loose a drop of thin ca will keep them tight as long as the planes around , but I did fill mine in also with some extra wood.cant hurt ! I was sort of angry that the kit did not come with decals nor cowl or pants ,not even a dash decal,For the price of this kit it should be more than a box of wood . I'll be following this and looking to see if you have any more questions, if you need some advice and cant wait, you can email me at [email protected] I'll post a pic when I get the tailfeathers in place should be monday the 14th Keep up the good work. |
RE: Midwest Extra 300xs Build
Thanks for the info Cyberwolf, I will definitely look at the landing gear mount construction when I get to that point. So far for me it has been a pretty slow build at this point. I will be starting on the fuselage this week hopefully. Keep getting interrupted with daily responsibilities and work, not to mention the crashed processor. Thought I had lost all my data as I had the previous PC's drives set up on a raid controller. Turns out the new mother board was not compatible with with the Promise Raid. Had to get another loaner PC and set the raid drives up in it to retrieve data, all is well though. I didn't get any plan(drawing) addendum but I did get the manual addendum if that is what you mean. That is the first thing I did. I will be using the fiberglass wheel pants and cowling from Stans Fiber-tech. Your'e very right about the hardware and accessories in this kit, they are sorely lacking. I am looking forward to your pics on this build as well.
Thanks, Bob |
RE: Midwest Extra 300xs Build
1 Attachment(s)
Heres a couple of it sitting together ,the wing is attached but the tail feathers are just setting in place .
|
RE: Midwest Extra 300xs Build
Cool!!
I remember those days when I was building the plane. It was fun to imagine how the plane will be at the end. Last weekend I maiden my MW extra300S again after last year crash. I crashed because I fogot to connect the ailerons after a short stop and go. My smoke system failed to work so I landed the plane quickly and removed the wing, fixed to smoke tank and attached the wing (without connecting the ailerons) and flew again without a pre-flight check. In the air, whoow, into the trees and fell down 40 meters, ripped my tail completely and stripped my wingtip. And ofcourse all plastic parts were broken. But now my I've got my extra up and running again and better then ever. Finally I've got the best stripescheme I have ever made. And I installed a little down trim on my engine. It seems like really helping landing the plane. The first and last two landings this weekend were landings like the real one. I mean a touchdown with two wheels and a long after run. And again I felt flying this plane almost better then ..... You know. You better get it finished quickly. :-) Greetz, Thierry |
RE: Midwest Extra 300xs Build
Man have I got some work to do!! I am no where near that stage yet, although I will be starting the fuselage soon. Looks like your'e almost there.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
I have a good start on the covering ,heres a couple pics .if it looks familar its because I copied the patterns of this months Model Aviation cover page ,well sort of *L*
|
RE: Midwest Extra 300xs Build
[sm=thumbup.gif]Nice colors, I really like tail detail. Looks like it was pretty tough to do though. Did you use the Monocote on Ultracote with windex or something else for the detail?
|
RE: Midwest Extra 300xs Build
Its all in monokote trial and fit untill it looked about right them ironed it on with my trim iron on low heat .its a real pain I should have maybe got in touch with a guy that does graphics and had him do it , I still just may on the wing .
|
RE: Midwest Extra 300xs Build
Well I heard the windex method works pretty good, and left to dry overnight, won't peal off. That looks great, wish I had the patience. I might try the windex, that is if I ever come up with a covering scheme.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
I started building the fuse today but before I get to that I have a few pictures of the leading edge shaping on the stab. After shaping, the tip is marked, cut off, and saved for fitting later on when installing the stab in the fuselage.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
Started by laying out the fuse sides and doublers and checking for the proper curve and marking the insides of each half. The curves needs to be toward the outside of the fuselage. After matching the sides up, I measured and marked the 6mm lines for the doubler edges on the front of both front sides(inside). In picture 3, I pinned the front and rear fuselage side to the plan with the inside facing up.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
After pinning the side to the plan,I glued the seam with thin CA. Then I added the top and bottom fuse doubler and glued them as well. Nest I added the Stab doubler to the rear of the fuse side.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
When I started to do the opposite fuselage side it dawned on me that I couldn't pin this side to the plan with the inside that I marked facing up. Only one side will be correctly oriented over the plan with the inside facing up. So what I did was clamped and pinned the completed side to the other as a guide for correct alignment. I also put wax paper between the two sides to avoid gluing them together. After alignment was correct I glued the doublers on and started laying out the fuse top above the top view of the plan.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
I placed both FT1 pieces over the plan and glued them together. Then cut the doublers for the front and rear and glued them in place. Next I added FT2 over the plans and sanded the ends for a good fit and glued in place. Again the same process for FT3.
|
RE: Midwest Extra 300xs Build
1 Attachment(s)
After all 3 fuse tops were pinned and glued to the plan I decided to do a dry run with the formers f3 -f7 and both fuse sides to check for any mistakes and squareness. I might also see any tab misalignments at this time before gluing everything up. I used painters tape instead of glue for the dry run.
|
RE: Midwest Extra 300xs Build
Hi
I was just wondering who has ever flown this model before, how are the 3D flight performance on this beauty. Keep up the great work !!! So far looks awesome !!! :D And another question... how those Brison Engines run? And which other gas engines would you recomend? |
RE: Midwest Extra 300xs Build
Can't say personally how the Midwest flies, however from all the reading I have done, it will pretty much do what the pilot skills allow. As far as 3D, It's a matter of equipment, setup, balancing and such.
The Brison 3.2 engine is awesome. It came off of a 29% Ultimate a friend of mine had. The DA 50 would probably be another good choice for this plane, its a little lighter, yet it does cost more. There are probably others who have owned this model and will chime in for more accurate flight reports. Personally, I can't wait to fly this build, however IT will be far more capable than I am. |
All times are GMT -8. The time now is 05:37 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.