Bootlegger?
#126
Senior Member
My Feedback: (1)
Join Date: Dec 2008
Location: Hueytown, AL
Posts: 624
Likes: 0
Received 0 Likes
on
0 Posts
RE: Bootlegger?
Thanks Paul,
I guess that may be why the Ex Port is lower in the cylinder than the other long rod motors !! The part I don't understand is the piston speed in a long rod will be higher than in a short rod turning the same RPM !!
You would think they would work out the torque and HP curve to come in @ a lower RPM because of the excess Piston speed..
Anyway I'm going OLD SCHOOL now where did I put them 11X7
Dave..
I guess that may be why the Ex Port is lower in the cylinder than the other long rod motors !! The part I don't understand is the piston speed in a long rod will be higher than in a short rod turning the same RPM !!
You would think they would work out the torque and HP curve to come in @ a lower RPM because of the excess Piston speed..
Anyway I'm going OLD SCHOOL now where did I put them 11X7
Dave..
#127
Senior Member
My Feedback: (1)
Join Date: Dec 2008
Location: Hueytown, AL
Posts: 624
Likes: 0
Received 0 Likes
on
0 Posts
RE: Bootlegger?
Here is the latest on my project ! I test fit all the formers and made sure the fiberglass top would work out !!
One thing I found out with the balsa fuse side being a stright line from the top of the firewall back to the tail, I had to cut a strip off the fiberglass piece to lower it so it would match the plans. The strip is 3/8" at the front and 5/8" @ the rear. Worked out fine ..
Dave...
One thing I found out with the balsa fuse side being a stright line from the top of the firewall back to the tail, I had to cut a strip off the fiberglass piece to lower it so it would match the plans. The strip is 3/8" at the front and 5/8" @ the rear. Worked out fine ..
Dave...
#132
My Feedback: (3)
Join Date: Apr 2008
Location: Montreal,
QC, CANADA
Posts: 5,200
Likes: 0
Received 5 Likes
on
5 Posts
RE: Bootlegger?
I gave that one a thought too. While having a removable top Arrow style is certainly more practical, it is not quite as elegant as the single fuse.
The main issue I see if making it a single piece fuse is the finish required to the fuse before permanently attaching the deck to it. I suppose there is a way to install the deck as if it were going to be removable (i.e., with some strips down the side top of the fuse to anchor the deck to), tack glue it, sand the job to uniformity, glass the wood and they paint the items separately so one can also finish the fuse area where the deck goes. The only drawback is that the seam would be visible if bonding after paint.
I suppose the alternative would be to finish the fuse interior area before final finish of the exterior so that the deck can be permanently attached and finished together with the fuse. This might be a better option so that the fuse is well blended in finish.
What do you think Dave?
David
The main issue I see if making it a single piece fuse is the finish required to the fuse before permanently attaching the deck to it. I suppose there is a way to install the deck as if it were going to be removable (i.e., with some strips down the side top of the fuse to anchor the deck to), tack glue it, sand the job to uniformity, glass the wood and they paint the items separately so one can also finish the fuse area where the deck goes. The only drawback is that the seam would be visible if bonding after paint.
I suppose the alternative would be to finish the fuse interior area before final finish of the exterior so that the deck can be permanently attached and finished together with the fuse. This might be a better option so that the fuse is well blended in finish.
What do you think Dave?
David
#133
My Feedback: (58)
Join Date: Nov 2002
Location: Knoxville,
TN
Posts: 1,807
Likes: 0
Received 0 Likes
on
0 Posts
RE: Bootlegger?
Make it one piece.. less chance for flexing and twisting, plus a much better finish for the plane and you can blend it in and make it seamless.
just my 2 cents if i was building one...
s.
just my 2 cents if i was building one...
s.
#134
Senior Member
My Feedback: (1)
Join Date: Dec 2008
Location: Hueytown, AL
Posts: 624
Likes: 0
Received 0 Likes
on
0 Posts
RE: Bootlegger?
Guy's,
I think I'm going to make is as close to the orignal Bootlegger as I can !! David a one piece fuse would look as you put it " more elegant" than two piece with a seam showing . I use a product called Aero lite from Aircraft Spruce Co. (its a two part epoxy filler) This stuff is as strong as any product you can buy to fill gaps and seams !! It sands like chalk and is very lite, makes great fillets around the wing,stab and rudder also.. I'm looking forward to blending the top piece in to the balsa sides .
So I guess you have my answer !!
Dave..
I think I'm going to make is as close to the orignal Bootlegger as I can !! David a one piece fuse would look as you put it " more elegant" than two piece with a seam showing . I use a product called Aero lite from Aircraft Spruce Co. (its a two part epoxy filler) This stuff is as strong as any product you can buy to fill gaps and seams !! It sands like chalk and is very lite, makes great fillets around the wing,stab and rudder also.. I'm looking forward to blending the top piece in to the balsa sides .
So I guess you have my answer !!
Dave..
#136
Senior Member
My Feedback: (1)
Join Date: Dec 2008
Location: Hueytown, AL
Posts: 624
Likes: 0
Received 0 Likes
on
0 Posts
RE: Bootlegger?
Guy's
Here is the latest on the legger !! Its all framed up and glued together the formers worked out fine after a little adj ! I built the fuse upside down using the stright edge on the top of the sides. After glueing it all together I turned it over in the jig dropped the fiberglas top on and it fit like glove !!! More to come ...
Dave.
Here is the latest on the legger !! Its all framed up and glued together the formers worked out fine after a little adj ! I built the fuse upside down using the stright edge on the top of the sides. After glueing it all together I turned it over in the jig dropped the fiberglas top on and it fit like glove !!! More to come ...
Dave.
#137
My Feedback: (10)
Join Date: Sep 2004
Location: Waco,
TX
Posts: 497
Likes: 0
Received 0 Likes
on
0 Posts
RE: Bootlegger?
I just found 2 OS 61 VF's so I have ordered the Bootlegger from Don at RCair so I will start on it in the next 2 weeks. I plan on building it with the flat stab
and Steve's scheme
and Steve's scheme
#138
Senior Member
My Feedback: (1)
Join Date: Dec 2008
Location: Hueytown, AL
Posts: 624
Likes: 0
Received 0 Likes
on
0 Posts
RE: Bootlegger?
Hey Thats great Todd, Glad you found the VF 61's !! Keep in touch on your build when you get started !!
I orded a belly pan for My Southern RC fiberglass Boot from RCaiir and the thing fit just like the orignal.
Dave..
I orded a belly pan for My Southern RC fiberglass Boot from RCaiir and the thing fit just like the orignal.
Dave..
#139
Junior Member
Join Date: Jul 2010
Location: Bearley, UNITED KINGDOM
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
I am UK based and about to start the build of a Bootlegger enlarged by 10% for a K&B 100 r/e. The plan I have shows a 0/0/0 set up for thrustline/wing/tail incidence and no side thrust. Is this correct please?