OPS .45 DF first runs
#1
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
OPS .45 DF first runs
Somebody has to post something..
I haven't progressed much in the workshop for a while, but employment is not a bad thing. Just finished a major install project (month on site) and hope things get a little quieter through Dec as the flying season becomes a fading memory.
Just committed the first two runs on one of my OPS .45 DF engines. Been fondling them for too long, needed inspiration.
Fuel: 15% nitro, 23% total oil syn/cas
Prop: Run #1 Eliminator P-8 7.375 x 8.25, Run #2 P-10 7.375 x 7.75
Weather: dry and a few degrees above freezing
Pipe: OPS open pipe
Carb: Jett 11mm borrowed from the OPS .65
Run 1 short - warmed up and madly cranking the needle in to avoid drowning, staged and rich saw close to 22k but the behaviour and tach said it needed a bit less load for early static runs. Shut down, cooled off, and switched to the P-10.
Engine starts and handles like an OPS.. i.e. too easy so far.
Run 2 - happily jumped on the pipe, running staged but real fat 22,500-22,700, slightly leaner and cleaner, saw 23,700 but a fair bit to go yet. Engine was tight again soon as it cooled down. Target in the air (for straight line speed) per the overseas speed freak's experience and advice is 26.5k. Should move a Demon along ok.
I haven't progressed much in the workshop for a while, but employment is not a bad thing. Just finished a major install project (month on site) and hope things get a little quieter through Dec as the flying season becomes a fading memory.
Just committed the first two runs on one of my OPS .45 DF engines. Been fondling them for too long, needed inspiration.
Fuel: 15% nitro, 23% total oil syn/cas
Prop: Run #1 Eliminator P-8 7.375 x 8.25, Run #2 P-10 7.375 x 7.75
Weather: dry and a few degrees above freezing
Pipe: OPS open pipe
Carb: Jett 11mm borrowed from the OPS .65
Run 1 short - warmed up and madly cranking the needle in to avoid drowning, staged and rich saw close to 22k but the behaviour and tach said it needed a bit less load for early static runs. Shut down, cooled off, and switched to the P-10.
Engine starts and handles like an OPS.. i.e. too easy so far.
Run 2 - happily jumped on the pipe, running staged but real fat 22,500-22,700, slightly leaner and cleaner, saw 23,700 but a fair bit to go yet. Engine was tight again soon as it cooled down. Target in the air (for straight line speed) per the overseas speed freak's experience and advice is 26.5k. Should move a Demon along ok.
#2
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
I'm looking forward to following up with the K&B 7.5's after the OPS, and comparing apples to apples on the test stand. Haven't run those yet either. Folks say the APC 7.4x8.4 was a good prop for it, I picked the P-8 as a close substitute.
#4
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
It was running similar rpm to a MAC open pipe. I haven't taken/sent you a pic yet, but the inlet is taking a bit of a browning/beating from combustion temps, and I worry the resin may be starting to break down. I'll get some pics for you.
It sure is light, and it sure looks trick!
It sure is light, and it sure looks trick!
#5
What temp is it running? I post cured the pipe at 425F and the resin is supposed to be good to 390F. It does get brown from heat, that is normal. Let me know if it has issues and I will take it up with the manufacturer of the resin system.
Scott
Scott
#6
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
I'll poke at it with clear mind/eyeballs and get some pics, but we ought to email on this topic from here on.
If I owned a temp gauge I could tell you something more helpful. The local hardware import chain has a sale on now and I saw one there.
If I owned a temp gauge I could tell you something more helpful. The local hardware import chain has a sale on now and I saw one there.
#7
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
This is also in the lineup for some bench running, and yeah I'll get video this time.
I don't expect it to threaten CP's 202mph Nelson FAI Demon, but it'll will be good fun nonetheless.
I like the integral exhaust stub, no need for exhaust options on such a singular purpose engine.
Picco 40 FAI
Yeah this ain't earth shattering excitement but there were too many cobwebs on this forum..
Thanks Jeremy BTW - it shined up really nicely too.
I don't expect it to threaten CP's 202mph Nelson FAI Demon, but it'll will be good fun nonetheless.
I like the integral exhaust stub, no need for exhaust options on such a singular purpose engine.
Picco 40 FAI
Yeah this ain't earth shattering excitement but there were too many cobwebs on this forum..
Thanks Jeremy BTW - it shined up really nicely too.
#8
My Feedback: (2)
that is a picco in the pics not ops
still a good motor.
one problem is your pipe it looks to be too small at the max diameter that looks like an fai pipe
a nitro pipe is much fatter at the large bell u should pop up to 28.5 on 25% nitro u also have a little too much oil these motors when I ran them
liked 18% with a little caster I used 3% added.
in the boats I used to run on an audio tach I was getting over 30k on 50% (OPS)
still a good motor.
one problem is your pipe it looks to be too small at the max diameter that looks like an fai pipe
a nitro pipe is much fatter at the large bell u should pop up to 28.5 on 25% nitro u also have a little too much oil these motors when I ran them
liked 18% with a little caster I used 3% added.
in the boats I used to run on an audio tach I was getting over 30k on 50% (OPS)
#9
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
that is a picco in the pics not ops
still a good motor.
one problem is your pipe it looks to be too small at the max diameter that looks like an fai pipe
a nitro pipe is much fatter at the large bell u should pop up to 28.5 on 25% nitro u also have a little too much oil these motors when I ran them
liked 18% with a little caster I used 3% added.
in the boats I used to run on an audio tach I was getting over 30k on 50% (OPS)
still a good motor.
one problem is your pipe it looks to be too small at the max diameter that looks like an fai pipe
a nitro pipe is much fatter at the large bell u should pop up to 28.5 on 25% nitro u also have a little too much oil these motors when I ran them
liked 18% with a little caster I used 3% added.
in the boats I used to run on an audio tach I was getting over 30k on 50% (OPS)
It's half OPS, it's the same P.
#10
My Feedback: (2)
did not see it till u mentioned picos have many parts that will change on to an ops I have over 30 ops 40/45/60/65/67 motors plus many spare parts I run most on 30%+ cold plugs I do have a custom rossi 65 that has a titanium rod
that that run on 75% custom cf prop that is approx. 10x10 has spun over 32k making a different pipe not fat enouth when it comes on the pipe.
I enjoy going fast turn left go faster and repeat.
that that run on 75% custom cf prop that is approx. 10x10 has spun over 32k making a different pipe not fat enouth when it comes on the pipe.
I enjoy going fast turn left go faster and repeat.
#12
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
I think boats may be harder on the rods with the rpm jumping up and down in rough water, not sure? I'd be interested in upgrading the conrods if available, though I haven't looked too hard yet. I'll try our domestic OPS and boat sources for starters.
Regards 10x10 props - a strong .90 will struggle to spin it at 16k, and 32k takes about 20hp. So if the .65 ran over 32k I'd expect to see a 6-10 on the front. Highly modified VAE and other 10cc performance engines used in F3 speed are running 26-27k in the air on props 8" or only a hair bigger, 10-13 pitch. A stock OPS .65 DF will run in the lower 20's on a 9-10.
Regards 10x10 props - a strong .90 will struggle to spin it at 16k, and 32k takes about 20hp. So if the .65 ran over 32k I'd expect to see a 6-10 on the front. Highly modified VAE and other 10cc performance engines used in F3 speed are running 26-27k in the air on props 8" or only a hair bigger, 10-13 pitch. A stock OPS .65 DF will run in the lower 20's on a 9-10.
#13
My Feedback: (2)
Join Date: Dec 2001
Location: Sacramento,,
CA
Posts: 126
Likes: 0
Received 0 Likes
on
0 Posts
This guy has alot of OPS parts for marine 45/67/80's in case you are in need. [email protected] I think he is in New York State, but unsure.
#14
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
Bill Hughes is also a good source for OPS parts, at least aero.
There is a marine supplier in Quebec with OPS parts, I got a .67 p/l set and a couple of other things.
There is a marine supplier in Quebec with OPS parts, I got a .67 p/l set and a couple of other things.
#16
My Feedback: (2)
no I ment 32000 this motor was specially built for one purpose 70%nitro very narrow rpm range on a custom pipe motor was guaranteed to run for 90 total minutes. this motor cost well inexcess of 1000$ it was designed for the purpose of the class d world speed record. fuel usage is inexcess of 6 oz per minute. most motors people are used to just like standard car motors are designed to last for many hours of use. compare this motor to a funny car engine that produces 5000 hp. runs for 1 run and needs to be rebuilt. essencially this is what I have. this is not normalls aspirated it uses compressed intake similar to what ys did on one early motor. that is why the very high numbers in conjunction with the fuel.
#19
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
That's why I'm curious.
A 10x10 at those rpm will need in the area of 20 horsepower. Highly modified .60's (example OPS VAE .60, Novarossi) on pipes as used in F3 speed are run up in the 26-27k range. We're talking 5 - 6hp tops. And a limited life span. Typical props 8x12, 8.5x11 range. Add all the nitromethane you want and totally tune the exhaust and intake system to get the volumetric efficiency up, and you might get an 8x10 into the upper '20's - in flight.
A 10x10 at those rpm will need in the area of 20 horsepower. Highly modified .60's (example OPS VAE .60, Novarossi) on pipes as used in F3 speed are run up in the 26-27k range. We're talking 5 - 6hp tops. And a limited life span. Typical props 8x12, 8.5x11 range. Add all the nitromethane you want and totally tune the exhaust and intake system to get the volumetric efficiency up, and you might get an 8x10 into the upper '20's - in flight.
#21
My Feedback: (22)
This is also in the lineup for some bench running, and yeah I'll get video this time.
I don't expect it to threaten CP's 202mph Nelson FAI Demon, but it'll will be good fun nonetheless.
I like the integral exhaust stub, no need for exhaust options on such a singular purpose engine.
Picco 40 FAI
Yeah this ain't earth shattering excitement but there were too many cobwebs on this forum..
Thanks Jeremy BTW - it shined up really nicely too.
I don't expect it to threaten CP's 202mph Nelson FAI Demon, but it'll will be good fun nonetheless.
I like the integral exhaust stub, no need for exhaust options on such a singular purpose engine.
Picco 40 FAI
Yeah this ain't earth shattering excitement but there were too many cobwebs on this forum..
Thanks Jeremy BTW - it shined up really nicely too.
Now I want it back hahaha
#22
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
If I launch the Demon pointed west with an autopilot, you'll just need to pick it out of the air with a 12 gauge when it flies over. Easy. 15 hours at top speed, lessee.. 15 hours x 60 minutes/hour = 900 minutes x 3oz fuel = 2700 oz = about 21 gallons.. no prob.
I'll brew up some 80/20 fuel and fire it up this weekend.
I'll brew up some 80/20 fuel and fire it up this weekend.
#25
Thread Starter
My Feedback: (1)
Join Date: May 2003
Location: Orangeville, ON, CANADA
Posts: 8,658
Likes: 0
Received 2 Likes
on
2 Posts
Not entirely - I got the cowl all reworked but needs a layer of light glass to homogenize it all together, installed servos, touched up some nicks and dings. Well on its way for the next thaw.
This year has been a dramatic example of the folly of working a little bit each on several projects. I have several projects all well on their way.. as to finishing them, well the theory is that winter is the time to do that.
This year has been a dramatic example of the folly of working a little bit each on several projects. I have several projects all well on their way.. as to finishing them, well the theory is that winter is the time to do that.