Fast plane for a TT Pro .36
#1
Thread Starter
My Feedback: (1)
Fast plane for a TT Pro .36
Can anybody recommend a simple to construct, high-speed sport plane for a Thunder Tiger Pro .36? I've currently have it installed on a Gremlin and the engine is turning about 20k on an 8x7 prop but the Gremlin is prone to surface flutter(I got it at a garage sale).
Any recommendations appreciated!
Any recommendations appreciated!
#2
My Feedback: (3)
Kit or ARF? The .36 is the hot rod engine for a .25 model and falls a little short on the .40 size models. You could build a Scat Cat rather light and inexpensively, or see if this ACE is still around.
https://www.rcgroups.com/forums/show...tern-Plane-Kit
I look for .25 models on a regular basis, hard to come by.
https://www.rcgroups.com/forums/show...el-tech-me-109
https://www.rcgroups.com/forums/show...tern-Plane-Kit
I look for .25 models on a regular basis, hard to come by.
https://www.rcgroups.com/forums/show...el-tech-me-109
#4
The World Models had an airplane called a Wingman II. It's a baby brother to the Sky Raider Mk II, at about 80% smaller in size. An internet search shows it out of stock, but if you could locate one, it would be a good match. It was primarily an electric airplane, but can be easily converted to glow. The larger Sky Raider Mk II would do about 90 mph on a Thunder Tigre Pro 40. I think the Wingman II on the TT 36 could do over 100 mph.
#5
Senior Member
My Feedback: (3)
I looked for a .20 to .25 sized P51 Mustang kit with no luck
I looked for a Diamond Dust Delta kit with no luck
Here is a Shrike.......Lanier Shrike 40 Short Kit RC Airplane Kit | eBay
Your engine with a 9 x 7 or 8 x 8 prop should be lots of fun.
I looked for a Diamond Dust Delta kit with no luck
Here is a Shrike.......Lanier Shrike 40 Short Kit RC Airplane Kit | eBay
Your engine with a 9 x 7 or 8 x 8 prop should be lots of fun.
#7
"It would be really easy to build up a slightly smaller Q500. Maybe 400 square inches. Foam cores, $40 worth of wood and a few micro servos. Make it V tail without rudder and landing gear and no more then 3 lbs. Could be 150mph capable".
I like this suggestion, if you are a builder? You could build a 75% Quickie with a 36" wingspan. My guess would be around 135 mph?
I like this suggestion, if you are a builder? You could build a 75% Quickie with a 36" wingspan. My guess would be around 135 mph?
#8
Thread Starter
My Feedback: (1)
Well, I went to the Swap Meet held by the Kansas City Radio Control club this morning. Came across an older arf from a company called Super Kraft. The model is a small-ish version of an F3D pylon racer. The Pro .36 is a drop-in fit. I think this will get past 130 mph without too much trouble. I will report back when I get to it in the early Spring. It's called the F3D-30.
#15
My Feedback: (1)
#21
My Feedback: (3)
Join Date: Jan 2013
Location: , ON, CANADA
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
If you are a builder, Matney models makes a few Q-40 planes that will suit your engine. Just build the wing lighter. It should end up a 4 pound plane and 400 square inches. A throttled engine should let it slow to land. Ken Fluney has done a few with Nelson SS Quickee engines with a carb and they fly really well and are very fast.
#22
My Feedback: (3)
Join Date: Jan 2013
Location: , ON, CANADA
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
I just looked at Matney’s site and remembered the EF1 models he sells. Perfect for your engine. Just beef up the firewall. There were some folks running piped 25 on a Proud Bird ARF a few years ago.
Hope this helps
Hope this helps
#23
My Feedback: (1)
Check this out::::
https://screamingeaglerc.com/p-51-speedster
ALL BALSA kit build, or custom order ARK Nitro 32-36 or EF1 1200KV Check out videos.
23K RPM on a 6s EF1 motor 8X5Graupner
OR APC 7X7 if you like nitro. Model is is the 125MPH range nitro of 150MPH EF1
Been flying them for over 20 years, Sheeted foam wing has undercamber and is a ***** cat grooves like its on rails, Even Dan Kane JR and Travis Flynn had to have a pull on the sticks back in mid 2000's on a Webra .35......
Just Sayin......................
https://screamingeaglerc.com/p-51-speedster
ALL BALSA kit build, or custom order ARK Nitro 32-36 or EF1 1200KV Check out videos.
23K RPM on a 6s EF1 motor 8X5Graupner
OR APC 7X7 if you like nitro. Model is is the 125MPH range nitro of 150MPH EF1
Been flying them for over 20 years, Sheeted foam wing has undercamber and is a ***** cat grooves like its on rails, Even Dan Kane JR and Travis Flynn had to have a pull on the sticks back in mid 2000's on a Webra .35......
Just Sayin......................