Jet Cat Help !!!!
#1
Thread Starter
My Feedback: (7)
Join Date: Dec 2004
Location: Toronto,
ON, CANADA
Posts: 242
Likes: 0
Received 0 Likes
on
0 Posts
Jet Cat Help !!!!
Hi Guys
I need help with my Titan
Engine spools up fine, pump ramps up engine reaches rpm When I shut the propane off or touch the throttle the engine quits and GSU reads "LOW RPM"Battery volts are good ,pump voltage is fine, no air bubles in the line
I need the Jet Cat experts help on this one
Thanks
Ted
I need help with my Titan
Engine spools up fine, pump ramps up engine reaches rpm When I shut the propane off or touch the throttle the engine quits and GSU reads "LOW RPM"Battery volts are good ,pump voltage is fine, no air bubles in the line
I need the Jet Cat experts help on this one
Thanks
Ted
#2
My Feedback: (23)
RE: Jet Cat Help !!!!
Hey Ted! long time no see![8D]
...if this hapens on start up ...i would say low presure in the gas tank...maybe you could try warm your gas tank with your hand...
...if this is after start up....while gas is not nesecery anymore ...and you mean that you can shut down the engine by removing the gas...
do you use auto drain after start up??...maybe you luse presure..
did in the past the engine worked fine...anything you changed??
good luchk friend....George from Korinth[8D]
...if this hapens on start up ...i would say low presure in the gas tank...maybe you could try warm your gas tank with your hand...
...if this is after start up....while gas is not nesecery anymore ...and you mean that you can shut down the engine by removing the gas...
do you use auto drain after start up??...maybe you luse presure..
did in the past the engine worked fine...anything you changed??
good luchk friend....George from Korinth[8D]
#3
My Feedback: (47)
RE: Jet Cat Help !!!!
Are you letting the engine ramp up fully, until the green light on the data board is lit? Sound like you are not allowing the ECU to fully complete the start cycle.
You should post manufacturer-specific questions in the JetCat service forum....might get a quicker answer. Good luck!
Cheers -
barry
You should post manufacturer-specific questions in the JetCat service forum....might get a quicker answer. Good luck!
Cheers -
barry
#4
My Feedback: (1)
RE: Jet Cat Help !!!!
ORIGINAL: TED ANTON
Hi Guys
I need help with my Titan
Engine spools up fine, pump ramps up engine reaches rpm When I shut the propane off or touch the throttle the engine quits and GSU reads "LOW RPM"Battery volts are good ,pump voltage is fine, no air bubles in the line
I need the Jet Cat experts help on this one
Thanks
Ted
Hi Guys
I need help with my Titan
Engine spools up fine, pump ramps up engine reaches rpm When I shut the propane off or touch the throttle the engine quits and GSU reads "LOW RPM"Battery volts are good ,pump voltage is fine, no air bubles in the line
I need the Jet Cat experts help on this one
Thanks
Ted
Is your fuel system ok?
Did you forget to unplug the vent line?
How much time on the engine?
Is this a new installation?
Has it ingested anything (FOD) lately?
Check your fuel for contamination. At the Mississippi jet rally a friend of mine kept having flame outs and it turned out to be water in his fuel (and lots of it).
#5
My Feedback: (61)
RE: Jet Cat Help !!!!
Ted wrote: <<When I shut the propane off>>
Are you manually running the propane valve ??
Plug in the gsu and watch the screen during the start, it will tell you when the start is complete. I wouid check your tx settings to be sure they are correct, re-learn the ecu and watch the start sequence on the gsu.
V..
Are you manually running the propane valve ??
Plug in the gsu and watch the screen during the start, it will tell you when the start is complete. I wouid check your tx settings to be sure they are correct, re-learn the ecu and watch the start sequence on the gsu.
V..
#6
My Feedback: (10)
Join Date: Feb 2003
Location: eureka,
MO
Posts: 85
Likes: 0
Received 0 Likes
on
0 Posts
RE: Jet Cat Help !!!!
I'm having the same problem. several seconds after the fuel starts to flow to the turbine everything shuts down. Also I can't get into the manual mode. any help is apprciated.
Thanks,
denny
Thanks,
denny