Official HPI Savage Flux XS thread...
09-20-2011, 07:39 AM
#451
Junior Member
Join Date: Apr 2007
Location: Mandan,
ND
Posts: 10
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: cooper998
four packs through and it flamed up! was running 3s Venom 5000 20c pack and motor and esc were getting very hot. Talked with the guys at the lhs and they suggested gearing down but did not have a smaller pinion at the time. My guess is HPI geared it to run 65mph so it could claim the top speed and would try to correct issues as they surfaced.
Unfortunately we suffer as guinea pigs while they get their act together, which I am sure they will.
Anyone know of a reliable esc I can use while I wait for a replacement? Will the Sidewinder Sv2 be good enough?
coop
four packs through and it flamed up! was running 3s Venom 5000 20c pack and motor and esc were getting very hot. Talked with the guys at the lhs and they suggested gearing down but did not have a smaller pinion at the time. My guess is HPI geared it to run 65mph so it could claim the top speed and would try to correct issues as they surfaced.
Unfortunately we suffer as guinea pigs while they get their act together, which I am sure they will.
Anyone know of a reliable esc I can use while I wait for a replacement? Will the Sidewinder Sv2 be good enough?
coop
I believe you are right, I think they geared it crazy high just so they could claim the high speeds. Therefore, the motor is drawing high amps and frying an ESC that can't handle the current draw. Now here is the question... do we go ahead and gear down and try to fix a problem that we shouldn't have to fix?
09-20-2011, 08:42 AM
#453
Senior Member
Thread Starter
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Official HPI Savage Flux XS thread...
I highly doubt it since castle does not.
To other posters... It will not do 65mph out of the box, not even on 3s. The manual describes the gearing needed. The box stock speed on 3s is about 52 mph if i remember correctly.
To other posters... It will not do 65mph out of the box, not even on 3s. The manual describes the gearing needed. The box stock speed on 3s is about 52 mph if i remember correctly.
09-20-2011, 08:46 AM
#454
Senior Member
Thread Starter
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Official HPI Savage Flux XS thread...
Coop, the stock ESC is a sidewinder v2 according to what I've been reading. If that's the case, it is considered to be around a 60A esc, though castle will not confirm it. If it is though, it should be adequate for most needs at this scale. I'm wondering if something they;ve done to it before giving it to HPI for this car, has somehow affected it adversely. If you want to be safe, I'd go for a Mamba Max Pro, and while I'm at it, I'd get a sensored motor too. Then I'd ebay the stock pieces.
09-20-2011, 08:50 AM
#455
Senior Member
Join Date: Sep 2011
Location: , FRANCE
Posts: 160
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Hi all,
I'm new to this forum and i do appreciate all your informations.
I'm very sorry for those having problem with burnt ESC.
I started RC with a car that never worked more than 5 min in a raw, I've spent money for spare parts and gave up, then I went for HPI E-Firestorm 10T Flux (105879), it's gorgeous, I keep it.
My first question is about the availability of this Savage XS, I'm in Europe and it's only pre-order, but it's the same for TowerHobbies, so where did you get yours from ?
I placed a pre-order for XS almost one month ago, but after reading all breakdown reports here, i'm a bit upset and it makes me wonder if i should change my order.
Thanks for your advices,
Peloche,
I'm new to this forum and i do appreciate all your informations.
I'm very sorry for those having problem with burnt ESC.
I started RC with a car that never worked more than 5 min in a raw, I've spent money for spare parts and gave up, then I went for HPI E-Firestorm 10T Flux (105879), it's gorgeous, I keep it.
My first question is about the availability of this Savage XS, I'm in Europe and it's only pre-order, but it's the same for TowerHobbies, so where did you get yours from ?
I placed a pre-order for XS almost one month ago, but after reading all breakdown reports here, i'm a bit upset and it makes me wonder if i should change my order.
Thanks for your advices,
Peloche,
09-20-2011, 08:58 AM
#456
Senior Member
Join Date: Dec 2010
Location: Livermore, CA
Posts: 249
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
I must admit that I'm glad that I waited to get my XS, these are the types of issues that I prefer being sorted out before buying a new model. I had bought the Revo when it first came out (I think back in '04) and told myself I'd never buy a first-run again.
I still can't wait to get mine though!!
I still can't wait to get mine though!!
09-20-2011, 10:16 AM
#459
Senior Member
My Feedback: (11)
RE: Official HPI Savage Flux XS thread...
ORIGINAL: chopan84
so i shouldnt have a problem running a 5450mah 2s lipo?? will it still do standing backflips on 2s?
so i shouldnt have a problem running a 5450mah 2s lipo?? will it still do standing backflips on 2s?
09-20-2011, 10:24 AM
#460
Join Date: Jul 2008
Location: Cambridge,
ON, CANADA
Posts: 3,107
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
I am guessing a manufacturing problem and a bad batch. If these ESCs are blowing this easily it must be that because they certainly wouldn't have missed such an obvious problem in testing.
Unfortunately, returning ESCs is likely going to lead to the same problem since they likely don't have a new batch. They probably had a bunch of truck shipped and a stack of spare ESCs which are from the same batch that they are giving people in the meantime knowing they are the same and likely to blow.
I think high C-rated batteries may help. For the people whose trucks didn't blow up, what was the C-rating? I ask because the charge and discharge cycling of the caps in the ESC will get hot and blow if the batteries can't supply what the ESC needs (ie. they don't like to work out of phase) so its not hard to believe if the motor is pushing the ESC to its limit that the batteries could be heating the caps too much if they aren't a high c-rating.
Should I just get it over with and blow my ESC when I get it and go on to the MMAx pro?
On an unrelated note I am in India right now and have been using my crawler in some amazing arrangements. If I didn't have a wonderful family I would throw away my return ticket (and have my XS and other RCs mailed here).
09-20-2011, 10:40 AM
#461
Senior Member
My Feedback: (11)
RE: Official HPI Savage Flux XS thread...
So in going back thru the thread I have found that between 8-10 esc's have gone up in smoke and that is almost split evenly on it happening with 2s and 3s lipos with "C" ratingsof 20 all the way to 50.
Like a couple of other people have said there must have been a bad bunch of ESC's.
Like a couple of other people have said there must have been a bad bunch of ESC's.
09-20-2011, 10:44 AM
#462
Senior Member
Thread Starter
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: Peloche
Hi all,
I'm new to this forum and i do appreciate all your informations.
I'm very sorry for those having problem with burnt ESC.
I started RC with a car that never worked more than 5 min in a raw, I've spent money for spare parts and gave up, then I went for HPI E-Firestorm 10T Flux (105879), it's gorgeous, I keep it.
My first question is about the availability of this Savage XS, I'm in Europe and it's only pre-order, but it's the same for TowerHobbies, so where did you get yours from ?
I placed a pre-order for XS almost one month ago, but after reading all breakdown reports here, i'm a bit upset and it makes me wonder if i should change my order.
Thanks for your advices,
Peloche,
Hi all,
I'm new to this forum and i do appreciate all your informations.
I'm very sorry for those having problem with burnt ESC.
I started RC with a car that never worked more than 5 min in a raw, I've spent money for spare parts and gave up, then I went for HPI E-Firestorm 10T Flux (105879), it's gorgeous, I keep it.
My first question is about the availability of this Savage XS, I'm in Europe and it's only pre-order, but it's the same for TowerHobbies, so where did you get yours from ?
I placed a pre-order for XS almost one month ago, but after reading all breakdown reports here, i'm a bit upset and it makes me wonder if i should change my order.
Thanks for your advices,
Peloche,
09-20-2011, 10:45 AM
#463
Senior Member
Thread Starter
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: t9dragon
So in going back thru the thread I have found that between 8-10 esc's have gone up in smoke and that is almost split evenly on it happening with 2s and 3s lipos with ''C'' ratingsof 20 all the way to 50.
Like a couple of other people have said there must have been a bad bunch of ESC's.
So in going back thru the thread I have found that between 8-10 esc's have gone up in smoke and that is almost split evenly on it happening with 2s and 3s lipos with ''C'' ratingsof 20 all the way to 50.
Like a couple of other people have said there must have been a bad bunch of ESC's.
09-20-2011, 12:20 PM
#464
Senior Member
Join Date: May 2008
Location: PalmerstonOntario, CANADA
Posts: 9,180
Likes: 0
Received 1 Like
on
1 Post
RE: Official HPI Savage Flux XS thread...
ORIGINAL: Peloche
Hi all,
I'm new to this forum and i do appreciate all your informations.
I'm very sorry for those having problem with burnt ESC.
I started RC with a car that never worked more than 5 min in a raw, I've spent money for spare parts and gave up, then I went for HPI E-Firestorm 10T Flux (105879), it's gorgeous, I keep it.
My first question is about the availability of this Savage XS, I'm in Europe and it's only pre-order, but it's the same for TowerHobbies, so where did you get yours from ?
I placed a pre-order for XS almost one month ago, but after reading all breakdown reports here, i'm a bit upset and it makes me wonder if i should change my order.
Thanks for your advices,
Peloche,
Hi all,
I'm new to this forum and i do appreciate all your informations.
I'm very sorry for those having problem with burnt ESC.
I started RC with a car that never worked more than 5 min in a raw, I've spent money for spare parts and gave up, then I went for HPI E-Firestorm 10T Flux (105879), it's gorgeous, I keep it.
My first question is about the availability of this Savage XS, I'm in Europe and it's only pre-order, but it's the same for TowerHobbies, so where did you get yours from ?
I placed a pre-order for XS almost one month ago, but after reading all breakdown reports here, i'm a bit upset and it makes me wonder if i should change my order.
Thanks for your advices,
Peloche,
09-20-2011, 08:53 PM
#468
Member
Join Date: Mar 2005
Location: , BC, CANADA
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
they told me they will send out a replacement next week from new shipment. not sure if they meant another batch?!
by the way, is there any upgrade service from hpi? like I just add money to get a replacement of Mamba Max Pro instead?
by the way, is there any upgrade service from hpi? like I just add money to get a replacement of Mamba Max Pro instead?
09-20-2011, 10:08 PM
#469
Senior Member
Join Date: Sep 2011
Location: , FRANCE
Posts: 160
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Hi dcfever,
HPI Savage XS ESC stock is Flux Vapor, on HPI site they propose as option part 2 ESC:
One is Bullet ESC standard and the second one is Flux 2350 standard.
HPI Savage XS ESC stock is Flux Vapor, on HPI site they propose as option part 2 ESC:
One is Bullet ESC standard and the second one is Flux 2350 standard.
09-20-2011, 10:25 PM
#470
Senior Member
Thread Starter
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: dcfever
they told me they will send out a replacement next week from new shipment. not sure if they meant another batch?!
by the way, is there any upgrade service from hpi? like I just add money to get a replacement of Mamba Max Pro instead?
they told me they will send out a replacement next week from new shipment. not sure if they meant another batch?!
by the way, is there any upgrade service from hpi? like I just add money to get a replacement of Mamba Max Pro instead?
09-21-2011, 05:03 AM
#471
Senior Member
Join Date: Dec 2010
Location: Livermore, CA
Posts: 249
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Anybody know if this battery will fit? The specs are right but I'm not sure about the cables coming from the center instead of the side of the battery. I don't have my XS yet but am trying to line up some batteries for when it does get here.
http://www.hobbyking.com/hobbyking/s...arehouse_.html
What do you guys think about starting a separate thread just for batteries so we can get a good list of what does and doesn't fit? I've followed this thread from day one and there is some good battery info in heres, but it's getting long enough that it's becoming a little tedious to sort through and find the info I am looking for.
http://www.hobbyking.com/hobbyking/s...arehouse_.html
What do you guys think about starting a separate thread just for batteries so we can get a good list of what does and doesn't fit? I've followed this thread from day one and there is some good battery info in heres, but it's getting long enough that it's becoming a little tedious to sort through and find the info I am looking for.
09-21-2011, 09:31 AM
#472
Senior Member
My Feedback: (11)
RE: Official HPI Savage Flux XS thread...
ORIGINAL: Johnbalz
Anybody know if this battery will fit? The specs are right but I'm not sure about the cables coming from the center instead of the side of the battery. I don't have my XS yet but am trying to line up some batteries for when it does get here.
http://www.hobbyking.com/hobbyking/s...arehouse_.html
What do you guys think about starting a separate thread just for batteries so we can get a good list of what does and doesn't fit? I've followed this thread from day one and there is some good battery info in heres, but it's getting long enough that it's becoming a little tedious to sort through and find the info I am looking for.
Anybody know if this battery will fit? The specs are right but I'm not sure about the cables coming from the center instead of the side of the battery. I don't have my XS yet but am trying to line up some batteries for when it does get here.
http://www.hobbyking.com/hobbyking/s...arehouse_.html
What do you guys think about starting a separate thread just for batteries so we can get a good list of what does and doesn't fit? I've followed this thread from day one and there is some good battery info in heres, but it's getting long enough that it's becoming a little tedious to sort through and find the info I am looking for.
Here are the measurements for the battery compartment.. 143mm x 47mm x 31mm
09-21-2011, 01:45 PM
#473
Senior Member
Join Date: Dec 2010
Location: Livermore, CA
Posts: 249
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
ORIGINAL: t9dragon
From looking at the measurements for the battery box and the ones for the battery you are asking about it would be a tight fit. It is better to have the wires coming from the top of the battery than the side for the XS.
Here are the measurements for the battery compartment.. 143mm x 47mm x 31mm
ORIGINAL: Johnbalz
Anybody know if this battery will fit? The specs are right but I'm not sure about the cables coming from the center instead of the side of the battery. I don't have my XS yet but am trying to line up some batteries for when it does get here.
http://www.hobbyking.com/hobbyking/s...arehouse_.html
What do you guys think about starting a separate thread just for batteries so we can get a good list of what does and doesn't fit? I've followed this thread from day one and there is some good battery info in heres, but it's getting long enough that it's becoming a little tedious to sort through and find the info I am looking for.
Anybody know if this battery will fit? The specs are right but I'm not sure about the cables coming from the center instead of the side of the battery. I don't have my XS yet but am trying to line up some batteries for when it does get here.
http://www.hobbyking.com/hobbyking/s...arehouse_.html
What do you guys think about starting a separate thread just for batteries so we can get a good list of what does and doesn't fit? I've followed this thread from day one and there is some good battery info in heres, but it's getting long enough that it's becoming a little tedious to sort through and find the info I am looking for.
Here are the measurements for the battery compartment.. 143mm x 47mm x 31mm
09-21-2011, 01:47 PM
#474
Senior Member
My Feedback: (11)
RE: Official HPI Savage Flux XS thread...
ORIGINAL: Johnbalz
Thanks. Yeah, I figured the battery itself would fit based on the battery box size, but since I don't have my XS yet I wasn't sure about the wires coming from the center versus the side like most packs. I'm still not sure what packs to buy. I'd like to pick up a couple 2S and a couple 3S packs.
Thanks. Yeah, I figured the battery itself would fit based on the battery box size, but since I don't have my XS yet I wasn't sure about the wires coming from the center versus the side like most packs. I'm still not sure what packs to buy. I'd like to pick up a couple 2S and a couple 3S packs.
09-22-2011, 10:26 AM
#475
Join Date: Jul 2008
Location: Cambridge,
ON, CANADA
Posts: 3,107
Likes: 0
Received 0 Likes
on
0 Posts
RE: Official HPI Savage Flux XS thread...
Mine just cleared customs today after being there for eight days. Looks like it will arrive in the next day or two. I plan on removing the 'bomb' right away. I am considering calling HPI saying I know of the multiple ESC fires and am not interested in trying considering the precedent for these things to go up in smoke. I don't like the idea of subjecting myself to the nerves of wondering if or when its going to go. If they ask me to start a fire to see if I am warranty eligible I will find that funny.