EME 35/ EME 60 released
#1
Junior Member
Thread Starter
Join Date: Oct 2011
Location: zhejiang yongkang,
ID, CHINA
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
EME 35/ EME 60 released
Hello all,
EME 35/ EME 60 are available now. The engines are sending to dealers worldwide and come to market soon.
EME 35 relative pics are as follows.
EME 35/ EME 60 are available now. The engines are sending to dealers worldwide and come to market soon.
EME 35 relative pics are as follows.
#3
Junior Member
Thread Starter
Join Date: Oct 2011
Location: zhejiang yongkang,
ID, CHINA
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
RE: EME 35/ EME 60 released
There aretest scratches and videos.
Kinds of engines and mufflers are tested, including the tuned pipe for 50~60cc.
All of them are made by EME.
For EME 60,
Drive 23*10 Xoar Prop @ 6450 with stock muffler, still rich set
Drive 24*8 Xoar Prop more than 6600 RPM.
For EME 35,
Drive 19*8 Xoar Prop @ 7550~7600 with stock muffler, still rich set
Drive 20*8 Xoar Prop more than 7100 RPM.
Videos
http://www.youtube.com/watch?v=vgetx...ature=youtu.be
http://www.youtube.com/watch?v=E_DsDu3TMts
Moreover, dealers are still wanted. Pls contact [email protected]
Kinds of engines and mufflers are tested, including the tuned pipe for 50~60cc.
All of them are made by EME.
For EME 60,
Drive 23*10 Xoar Prop @ 6450 with stock muffler, still rich set
Drive 24*8 Xoar Prop more than 6600 RPM.
For EME 35,
Drive 19*8 Xoar Prop @ 7550~7600 with stock muffler, still rich set
Drive 20*8 Xoar Prop more than 7100 RPM.
Videos
http://www.youtube.com/watch?v=vgetx...ature=youtu.be
http://www.youtube.com/watch?v=E_DsDu3TMts
Moreover, dealers are still wanted. Pls contact [email protected]
#8
Join Date: Dec 2001
Location: Summerfield,
NC
Posts: 1,946
Likes: 0
Received 0 Likes
on
0 Posts
RE: EME 35/ EME 60 released
ORIGINAL: tande
Whats up with the twin/cylinder crank? ....
ORIGINAL: emengines
Moreover, some design details are as follows,
Moreover, some design details are as follows,
#9
Junior Member
Thread Starter
Join Date: Oct 2011
Location: zhejiang yongkang,
ID, CHINA
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
RE: EME 35/ EME 60 released
ORIGINAL: skip1320
Send pic,s of that tune pipe stuck in wall behind 35,thanks
Send pic,s of that tune pipe stuck in wall behind 35,thanks
It is for 50~60cc single or 100~120 twin. A monster.
#10
Junior Member
Thread Starter
Join Date: Oct 2011
Location: zhejiang yongkang,
ID, CHINA
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
RE: EME 35/ EME 60 released
ORIGINAL: tande
Whats up with the twin/cylinder crank? ....
ORIGINAL: emengines
Moreover, some design details are as follows,
Moreover, some design details are as follows,
#11
Senior Member
RE: EME 35/ EME 60 released
Hi Jeame,
on the 35cc what is the distance from the back of the solid mount to the low mixture screw?
I'm asking as I was curious to see if it's possible to mount the engine without stand offs to the firewall and still have acess to the mixture screws.
Naurally a big hole in the firewall would be needed for the carb.
Also what is the distance from the back of the solid mount to the front of the prop hub?
on the 35cc what is the distance from the back of the solid mount to the low mixture screw?
I'm asking as I was curious to see if it's possible to mount the engine without stand offs to the firewall and still have acess to the mixture screws.
Naurally a big hole in the firewall would be needed for the carb.
Also what is the distance from the back of the solid mount to the front of the prop hub?
#12
Junior Member
Join Date: Mar 2010
Location: Jinhua, CHINA
Posts: 7
Likes: 0
Received 0 Likes
on
0 Posts
RE: EME 35/ EME 60 released
Hello,3136
It is possible to adjust the needle without stands if the firewall is less than 10mm
Pls check the dimention of EME 35 as link below,
http://www.emehobby.com/download_en.asp
Best Regards
It is possible to adjust the needle without stands if the firewall is less than 10mm
Pls check the dimention of EME 35 as link below,
http://www.emehobby.com/download_en.asp
Best Regards
#13
My Feedback: (2)
Join Date: Dec 2007
Location: Fort McMurray,
AB, CANADA
Posts: 4,121
Received 0 Likes
on
0 Posts
RE: EME 35/ EME 60 released
I have been watching EME for about two years now and have been impressed with the improvements. I just ordered a 120 to try this year from the distributor here in Canada, Thunderbolt RC.
#16
RE: EME 35/ EME 60 released
ORIGINAL: TunnelBill
Is anyone in the US selling and carry parts for the EME engine? I bought mine from Taildragger and they do not carry them anymore. Thanks
Is anyone in the US selling and carry parts for the EME engine? I bought mine from Taildragger and they do not carry them anymore. Thanks
DaleD