XYZ ENGINES
#276
RE: XYZ ENGINES
ORIGINAL: jssull00
Got a XYZ 26 with a front bearing going bad. I can't get the
hub off crank shaft. Used a puller and moderate heat but it
won't budge. Any suggestions ?
Got a XYZ 26 with a front bearing going bad. I can't get the
hub off crank shaft. Used a puller and moderate heat but it
won't budge. Any suggestions ?
-Dave
#279
RE: XYZ ENGINES
Note I'm assuming your engine is not one of the first (which had no collar on the threaded prop shaft) and does indeed have that collar. The collar is not a separate item, but is a projection on the prop shaft. The prop shaft is threaded at both ends (to screw into the crankshaft and for the prop nut), with the collar between. The photo shows the prop shaft partly removed. My collar's OD is shiny because I had to turn it down slightly.
Hold the prop hub with a wrench on its flats and unscrew the prop shaft with vice grips, soft vise jaws, etc.
-Dave
(added a few minutes later): Unscrew the prop shaft just a turn or 2, then use puller to pull hub off crankshaft taper. Heat might help, as might a hammer & creative language.
Hold the prop hub with a wrench on its flats and unscrew the prop shaft with vice grips, soft vise jaws, etc.
-Dave
(added a few minutes later): Unscrew the prop shaft just a turn or 2, then use puller to pull hub off crankshaft taper. Heat might help, as might a hammer & creative language.
#280
Junior Member
Join Date: Apr 2006
Location: Hamilton, OH
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Thanks Dave, it worked like a champ. This is a nice motor.
I have 56 flights of 11 minutes each when I noticed a lateral
movement in crankshaft. Need to check it out. This motor turns an
16-8 master airscrew at 8200+. It flies a Seagull Yak 90 very
well.
I have 56 flights of 11 minutes each when I noticed a lateral
movement in crankshaft. Need to check it out. This motor turns an
16-8 master airscrew at 8200+. It flies a Seagull Yak 90 very
well.
#281
Junior Member
Join Date: Apr 2006
Location: Hamilton, OH
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Well, turns out the bearings are fine (NGK). The
problem is the crank shaft. It was turned down too
small when manufactured. The front journal measures
(.47024") instead of (.47244").
problem is the crank shaft. It was turned down too
small when manufactured. The front journal measures
(.47024") instead of (.47244").
#282
My Feedback: (47)
Join Date: Apr 2009
Location: Whitestone,
NY
Posts: 1,895
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
A question for any gasser's out there. I was re-tuning my XYZ 50cc gasser this morning - finally got it right. Seems the low-speed needle was too closed, so the engine was cutting out at idle. And I opened up the high speed, which increased RPMs. So, good idle and high end, and smooth transition. Flew perfectly in the air, too, without the cowl. But once I put the cowl back on it ran like CRAP (in the air, seemed ok before takeoff). The engine would not advance to more than (it seemed) 1/3 throttle, no matter what I tried. Sounded like the engine was choking. Got it back safely, took the cowl off, and the engine ran perfectly again. Flew it, sans cowl, perfect engine response. So is the cowl cutting the airflow to my carb? Should I install a venturi to a hole in the cowl? (I've heard of this but never done it before.)
Or could this be a case of installing a nipple into the carb pressure plate and running a line to the body of the plane, for more constant pressure? Thanks.
Or could this be a case of installing a nipple into the carb pressure plate and running a line to the body of the plane, for more constant pressure? Thanks.
#283
My Feedback: (47)
Join Date: Apr 2009
Location: Whitestone,
NY
Posts: 1,895
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Also, I'm curious what props and RPM's people are getting with the XYZ 50. I'm finding I get more airspeed with my 78" Texas Hurricane using an APC 18x10. Faster than an APC 20x10. I'm not doing 3D, so am more interested in speed. What props and RPM's are other's getting?
#284
Junior Member
Join Date: Apr 2006
Location: Hamilton, OH
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Make sure you have enough exit area for air to
evacuate cowl. If the engine over heats it will lose
power or stop. You should have at least twice the
size hole for letting air out as inlet size. The inlet
should direct air over the cylinder and head and
any other holes covered over.
evacuate cowl. If the engine over heats it will lose
power or stop. You should have at least twice the
size hole for letting air out as inlet size. The inlet
should direct air over the cylinder and head and
any other holes covered over.
#289
My Feedback: (47)
Join Date: Apr 2009
Location: Whitestone,
NY
Posts: 1,895
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Octopus - If the price of XYZ 20's increases it will be getting very close to DLE 20 territory. Do you think people will still choose an XYZ over a DLE without much of a price incentive? Do you have any videos for the XYZ 20 on Youtube?
btw - aren't YOU sales XYZ?
btw - aren't YOU sales XYZ?
#291
My Feedback: (2)
Join Date: Dec 2004
Location: QuzhouZhe Jiang, CHINA
Posts: 229
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
No sure what will happen yet.
We do hope people will like XYZ new engines .
We haven't take any video yet.
I think there will have some video post by end users soon.
About wholesale .
At present we offer worldwide wholesale except USA.
We do hope people will like XYZ new engines .
We haven't take any video yet.
I think there will have some video post by end users soon.
About wholesale .
At present we offer worldwide wholesale except USA.
#296
Join Date: Oct 2006
Location: East Point,
GA
Posts: 200
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Hi all, hope to get some help here. I have an XYZ 53 twin. Love the engine so far but I haven't had more than 10 flights on it. Flew it two weeks ago and everything was peachy. Mtoday I got to the field and flipped it till I got a headache and it never started. I noticed fuel coming out of the carb so that wasnt the problem. On to spark. I pulled the plugs, grounded them against the jugs and no spark. I pulled off the ignition and noticed one of the black wires, the one that goes to the timing part on the engine, had some of the plastic covering scraped away. I put some electrical,tape over it and plugged everything back up. Now when I turn on the egnition switch, the ignition module hums. What dies this mean? Engine still didn't spark after numerous flips. New to gassers so any assistance would be greatly appreciated.
Also, if the diagnosis is the ignition module, can I just get any ignition module or do I need one compatible with this engine? Not sure I like the xyz ignition module if it craps out after 10 flights.
Thanks in advance,
Dan
Also, if the diagnosis is the ignition module, can I just get any ignition module or do I need one compatible with this engine? Not sure I like the xyz ignition module if it craps out after 10 flights.
Thanks in advance,
Dan
#297
My Feedback: (2)
Join Date: Dec 2004
Location: QuzhouZhe Jiang, CHINA
Posts: 229
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Hello Dan
Can you e-mail us the picture of your ignition at [email protected] ?
We can check and require free replacement for you if it`s a old version from factory !
I guess the bad sensor cased ignition short out .
Have a good day !
Can you e-mail us the picture of your ignition at [email protected] ?
We can check and require free replacement for you if it`s a old version from factory !
I guess the bad sensor cased ignition short out .
Have a good day !
#298
RE: XYZ ENGINES
ORIGINAL: secret_squirrel
Hi all, hope to get some help here. I have an XYZ 53 twin. Love the engine so far but I haven't had more than 10 flights on it. Flew it two weeks ago and everything was peachy. Mtoday I got to the field and flipped it till I got a headache and it never started. I noticed fuel coming out of the carb so that wasnt the problem. On to spark. I pulled the plugs, grounded them against the jugs and no spark. I pulled off the ignition and noticed one of the black wires, the one that goes to the timing part on the engine, had some of the plastic covering scraped away. I put some electrical,tape over it and plugged everything back up. Now when I turn on the egnition switch, the ignition module hums. What dies this mean? Engine still didn't spark after numerous flips. New to gassers so any assistance would be greatly appreciated.
Also, if the diagnosis is the ignition module, can I just get any ignition module or do I need one compatible with this engine? Not sure I like the xyz ignition module if it craps out after 10 flights.
Thanks in advance,
Dan
Hi all, hope to get some help here. I have an XYZ 53 twin. Love the engine so far but I haven't had more than 10 flights on it. Flew it two weeks ago and everything was peachy. Mtoday I got to the field and flipped it till I got a headache and it never started. I noticed fuel coming out of the carb so that wasnt the problem. On to spark. I pulled the plugs, grounded them against the jugs and no spark. I pulled off the ignition and noticed one of the black wires, the one that goes to the timing part on the engine, had some of the plastic covering scraped away. I put some electrical,tape over it and plugged everything back up. Now when I turn on the egnition switch, the ignition module hums. What dies this mean? Engine still didn't spark after numerous flips. New to gassers so any assistance would be greatly appreciated.
Also, if the diagnosis is the ignition module, can I just get any ignition module or do I need one compatible with this engine? Not sure I like the xyz ignition module if it craps out after 10 flights.
Thanks in advance,
Dan
2 to a Saito FG-57 and 2 to the XYZ 53 cc.
The two first worked for, say 10-10 flights. Then the spark becomes too weak.
The engines wont start.
So I bought 2 more in june this year. One of them never gave a spark. The other one can be started,
but only after, say, 10 - 20 seconds on a starter.
I also have RcExl on a G-38. Its beginning to show the same symptoms.
I have another set on a GT-80. It has been working so far, but it dont have that many flights yet.
I fear it will fail too.
Will try C&H Ignition now.
There is a discussion on it here;
http://www.rcuniverse.com/forum/m_11223166/tm.htm
#299
RE: XYZ ENGINES
I have sold well over 250 RCexl ignitions sense the first of the year and you have had more failures than all of them put together, You must have the worst luck of anybody I have ever seen or just doing something wrong.
And on another note, They have a two year warranty so why did not Octopus RC replace them.
Milton
And on another note, They have a two year warranty so why did not Octopus RC replace them.
Milton
#300
My Feedback: (2)
Join Date: Dec 2004
Location: QuzhouZhe Jiang, CHINA
Posts: 229
Likes: 0
Received 0 Likes
on
0 Posts
RE: XYZ ENGINES
Both Rcexl and Octopus RC will offer warranty service . it's no problem.
But i can not understand why the 4pcs Dan brought all have problem ?
Never met this before .
But i can not understand why the 4pcs Dan brought all have problem ?
Never met this before .