MIT Rigger(Design & Hand made in Taiwan)
#1
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
MIT Rigger(Design & Hand made in Taiwan)
Hi Guys:
We just completed the design and handy lay up of new rigger in Taiwan. It was designed and hand made by a Mr. Liu who live in Da-Lin with 40 years' experience on RC boat. I got this rigger and finished installation with QD29 Pioneer engine! Share some pictures with you! Wait for advanced testing when I have free time, may be on April.
We just completed the design and handy lay up of new rigger in Taiwan. It was designed and hand made by a Mr. Liu who live in Da-Lin with 40 years' experience on RC boat. I got this rigger and finished installation with QD29 Pioneer engine! Share some pictures with you! Wait for advanced testing when I have free time, may be on April.
#4
Senior Member
Join Date: Jan 2010
Location: Sanctuary PointNSW, AUSTRALIA
Posts: 358
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Hi ,just wondering if you happen to have a link or email where i can get one of these hulls from? What was the $ for the hull?
As i will be in the market for a Rigger soon
Thanks heaps
As i will be in the market for a Rigger soon
Thanks heaps
#5
Senior Member
Join Date: Sep 2008
Location: Kuching, Sarawak, MALAYSIA
Posts: 336
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Hi Dresden,
Sent u an email inquiring about this MIT rigger. I am in the market for one unit since last month lol. Please let me know soonest. Thanks.
Sent u an email inquiring about this MIT rigger. I am in the market for one unit since last month lol. Please let me know soonest. Thanks.
#6
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Hi Mickie:
Before this rigger, I was looking for a good looking rigger for a long time. I am sure it's best looking one in the current market, and it's very stable on the water with high speed. However, this rigger is not for selling, is builder try to promote his spirits on rigger! Only 3 sets we can see on RC experts' handin Taiwan(in the world). The price is different for each other, base on the relationship with him. I am not sure the builder would like tobuild one for you or others, and I am sure the price is cheaper than Insane BossRigger! The current new project to him for me is to hand made a 2012 clear canbon rigger. That's a challenge tous in RC boat area! Again, we are not business man,but I will ask him for your requirement. Good luck to you!
BR!
Ray
Before this rigger, I was looking for a good looking rigger for a long time. I am sure it's best looking one in the current market, and it's very stable on the water with high speed. However, this rigger is not for selling, is builder try to promote his spirits on rigger! Only 3 sets we can see on RC experts' handin Taiwan(in the world). The price is different for each other, base on the relationship with him. I am not sure the builder would like tobuild one for you or others, and I am sure the price is cheaper than Insane BossRigger! The current new project to him for me is to hand made a 2012 clear canbon rigger. That's a challenge tous in RC boat area! Again, we are not business man,but I will ask him for your requirement. Good luck to you!
BR!
Ray
#7
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
#8
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Hi Mickie & Latiff:
I contacted with buildr today, he said he can not meet your requirement in short time. Basically he needs 1~2 months to build a rigger and he will stop this rigger after completed following 2 sets for good friends. And he will begin to upgradeit as clear carbon version with new designed foot! The 1stone will be ready on April and belong to me.
He is willing to build for you, but fastest schedule will be the end of 2012! Can you wait for it?
Share some boat pictures with you:
DF 53" caverlar + QD35
PPB Drag Cat + QD29 Pioneer
I contacted with buildr today, he said he can not meet your requirement in short time. Basically he needs 1~2 months to build a rigger and he will stop this rigger after completed following 2 sets for good friends. And he will begin to upgradeit as clear carbon version with new designed foot! The 1stone will be ready on April and belong to me.
He is willing to build for you, but fastest schedule will be the end of 2012! Can you wait for it?
Share some boat pictures with you:
DF 53" caverlar + QD35
PPB Drag Cat + QD29 Pioneer
#9
Senior Member
Join Date: Jan 2010
Location: Sanctuary PointNSW, AUSTRALIA
Posts: 358
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
ORIGINAL: dresden5871
Hi Mickie & Latiff:
I contacted with buildr today, he said he can not meet your requirement in short time. Basically he needs 1~2 months to build a rigger and he will stop this rigger after completed following 2 sets for good friends. And he will begin to upgradeit as clear carbon version with new designed foot! The 1stone will be ready on April and belong to me.
He is willing to build for you, but fastest schedule will be the end of 2012! Can you wait for it?
Share some boat pictures with you:
DF 53" caverlar + QD35
PPB Drag Cat + QD29 Pioneer
Hi Mickie & Latiff:
I contacted with buildr today, he said he can not meet your requirement in short time. Basically he needs 1~2 months to build a rigger and he will stop this rigger after completed following 2 sets for good friends. And he will begin to upgradeit as clear carbon version with new designed foot! The 1stone will be ready on April and belong to me.
He is willing to build for you, but fastest schedule will be the end of 2012! Can you wait for it?
Share some boat pictures with you:
DF 53" caverlar + QD35
PPB Drag Cat + QD29 Pioneer
Is there any video of this rigger on the water yet?
Regards Mick
#10
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Hi Mickie:
Here they are:
1st set of Ver.2 with paint job, builder with Ver.1 & Ver.2, 1st set of Ver.2 on the water 1st time...........
The engine is Zen G260 w/o modified, need to get higher rpm of it!
www.youtube.com/watch
v.youku.com/v_show/id_XMzAxMjIxNzYw.html
Here they are:
1st set of Ver.2 with paint job, builder with Ver.1 & Ver.2, 1st set of Ver.2 on the water 1st time...........
The engine is Zen G260 w/o modified, need to get higher rpm of it!
www.youtube.com/watch
v.youku.com/v_show/id_XMzAxMjIxNzYw.html
#12
Senior Member
Join Date: Feb 2007
Location: Newcastle, UNITED KINGDOM
Posts: 1,385
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
The rigger in the first pictures looks nice, the only thing i can see might be a problem lies with the carb cover being so close to the carb, I am pretty sure on the Pioneer that Quickdraw recommend a considerable distance to be kept clear of the carb inlet to prevent airflow restriction and most likely resonance occuring between carb and the cowl.
Might be worth checking - but a good looking rigger that you have there.
Glenn
Might be worth checking - but a good looking rigger that you have there.
Glenn
#13
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Hi Glenn:
You are right, it may be a problem! I have no idea about this effection. Only try to improve it after testing on water. Thanks for your advise!
You are right, it may be a problem! I have no idea about this effection. Only try to improve it after testing on water. Thanks for your advise!
#14
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Hi Glenn:
Due to work in Beijing currently, I fired my MIT rigger 1st timetwo days ago! It looks good! Here are some data and video below:
MIT Rigger Maker : Mr. Liu - a teacher in Taiwan
Assemble & Drive : Ray Cheng
Video Shooter : Mr. Liu - a boss in Taiwan
Engine : QD29 Pioneer
Hardware : Speedmaster
Prop. : 6721/3
Rudder : 3mm w/o water pick up
Speed of 1st test run by laser gun(BUSHNELL) : 99KPH
Speed of 1st test run by GPS(GARMIN) : 115KPH
Many thanks for rigger hull maker : Mr. Liu (Dar-Lin)
Many thanks for video shooter : Mr. Liu (Professional shooter)
Many thanks for all my friends who supported me in the past!
WE CAN DO IT !!! TAIWAN NO.1 !!!
M.I.T. RIGGER NO.1 !!!
http://www.youtube.com/watch?v=y7Dbc...layer_embedded
http://www.youtube.com/watch?v=MhOX0...layer_embedded
Due to work in Beijing currently, I fired my MIT rigger 1st timetwo days ago! It looks good! Here are some data and video below:
MIT Rigger Maker : Mr. Liu - a teacher in Taiwan
Assemble & Drive : Ray Cheng
Video Shooter : Mr. Liu - a boss in Taiwan
Engine : QD29 Pioneer
Hardware : Speedmaster
Prop. : 6721/3
Rudder : 3mm w/o water pick up
Speed of 1st test run by laser gun(BUSHNELL) : 99KPH
Speed of 1st test run by GPS(GARMIN) : 115KPH
Many thanks for rigger hull maker : Mr. Liu (Dar-Lin)
Many thanks for video shooter : Mr. Liu (Professional shooter)
Many thanks for all my friends who supported me in the past!
WE CAN DO IT !!! TAIWAN NO.1 !!!
M.I.T. RIGGER NO.1 !!!
http://www.youtube.com/watch?v=y7Dbc...layer_embedded
http://www.youtube.com/watch?v=MhOX0...layer_embedded
#21
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
Yes, you have a sharp eyesight! You can change the position anywhere you like by using throttle line, just try to hold up the two end positions of throttle line by epoxy!
Ray
#23
Member
Thread Starter
Join Date: Jan 2010
Location: HsinchuR.O.C., TAIWAN
Posts: 48
Likes: 0
Received 0 Likes
on
0 Posts
RE: MIT Rigger(Design & Hand made in Taiwan)
2013 Carbon Version MIT Rigger
Here is video link : http://www.youtube.com/watch?v=2sD03...eature=mh_lolz
Here is video link : http://www.youtube.com/watch?v=2sD03...eature=mh_lolz