O.S. 61 Rear Exhaust Long Stroke Parts
#2
My Feedback: (58)
Join Date: Nov 2002
Location: Knoxville,
TN
Posts: 1,807
Likes: 0
Received 0 Likes
on
0 Posts
RE: O.S. 61 Rear Exhaust Long Stroke Parts
Have you tried tower hobbies? they might have old stock or a current egine with same drive washer. I currently have 2 OS long strokes rebuilding.
scott
scott
#4
Senior Member
My Feedback: (44)
Join Date: Feb 2008
Location: kuna,
ID
Posts: 896
Likes: 0
Received 0 Likes
on
0 Posts
RE: O.S. 61 Rear Exhaust Long Stroke Parts
search helipro' south under discontinued engines...and a cross check of the OS parts listing will give you a second source as well...they are not unique to the sf/rf series engines
#5
Thread Starter
My Feedback: (60)
Join Date: Oct 2003
Location: Bowie,
MD
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
RE: O.S. 61 Rear Exhaust Long Stroke Parts
ORIGINAL: lfinney
search helipro' south under discontinued engines...and a cross check of the OS parts listing will give you a second source as well...they are not unique to the sf/rf series engines
search helipro' south under discontinued engines...and a cross check of the OS parts listing will give you a second source as well...they are not unique to the sf/rf series engines
Thx u!
#6
My Feedback: (29)
RE: O.S. 61 Rear Exhaust Long Stroke Parts
Does that engine have a collet type drive washer? If so any engine that has the same dia. shaft where the collet rides is a compatable donor. An example of this is that I once needed one for a Rossi .45 and found that the one off a Saito .82 fit because they both had an 8mm shaft.
#7
Senior Member
My Feedback: (44)
Join Date: Feb 2008
Location: kuna,
ID
Posts: 896
Likes: 0
Received 0 Likes
on
0 Posts
RE: O.S. 61 Rear Exhaust Long Stroke Parts
i run several OS heli engines with the OS 4-46 vr-f drive washer and collet....OS heli engines come in at least three different flavors IE length and diameter
#9
RE: O.S. 61 Rear Exhaust Long Stroke Parts
Either one of these should work for an OS 61 RF rear exhaust.
http://www3.towerhobbies.com/cgi-bin...&I=LXCL44&P=SM
http://www3.towerhobbies.com/cgi-bin...&I=LXCL47&P=SM
This is the replacement drive washer for the following OS engines:
.61 SFN-H w/6B carb .61 SFN-H ABC w/6B
.61SF .61 SX-H Heli SE
.61 RX-H Heli RE.61 RFN-H RC
.61 RFN-H ABC RC.61 RF
The 61SF or 61RFrequiresthis thrust Washer http://www3.towerhobbies.com/cgi-bin...?&I=LXCW52&P=7 Also works on any of the above engines.
It will also work on OS 61FSR and OS 61VF's sometimeswithoutthe addition of the Thrust Washer.
All these engines use a 5/16 prop nut. From .61 to theFT120/160 http://www3.towerhobbies.com/cgi-bin...?&I=LXCT59&P=M
-61 SF -61 RF -60 FP -65 LA -61 FX -61 SX
-61 RX -61 LX -61, 65 and 91 VR series -91 SX-H
-70/91 Surpass -FT120/160
Regards
http://www3.towerhobbies.com/cgi-bin...&I=LXCL44&P=SM
http://www3.towerhobbies.com/cgi-bin...&I=LXCL47&P=SM
This is the replacement drive washer for the following OS engines:
.61 SFN-H w/6B carb .61 SFN-H ABC w/6B
.61SF .61 SX-H Heli SE
.61 RX-H Heli RE.61 RFN-H RC
.61 RFN-H ABC RC.61 RF
The 61SF or 61RFrequiresthis thrust Washer http://www3.towerhobbies.com/cgi-bin...?&I=LXCW52&P=7 Also works on any of the above engines.
It will also work on OS 61FSR and OS 61VF's sometimeswithoutthe addition of the Thrust Washer.
All these engines use a 5/16 prop nut. From .61 to theFT120/160 http://www3.towerhobbies.com/cgi-bin...?&I=LXCT59&P=M
-61 SF -61 RF -60 FP -65 LA -61 FX -61 SX
-61 RX -61 LX -61, 65 and 91 VR series -91 SX-H
-70/91 Surpass -FT120/160
Regards
#10
Thread Starter
My Feedback: (60)
Join Date: Oct 2003
Location: Bowie,
MD
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
RE: O.S. 61 Rear Exhaust Long Stroke Parts
ORIGINAL: Roguedog
Either one of these should work for an OS 61 RF rear exhaust.
http://www3.towerhobbies.com/cgi-bin...&I=LXCL44&P=SM
http://www3.towerhobbies.com/cgi-bin...&I=LXCL47&P=SM
This is the replacement drive washer for the following OS engines:
.61 SFN-H w/6B carb                     .61 SFN-H ABC w/6B
.61Â SFÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â .61 SX-H Heli SE
.61 RX-H Heli REÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â .61 RFN-H RC
.61 RFN-H ABC RCÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â .61 RF
The 61SF or 61RF requires this thrust Washer http://www3.towerhobbies.com/cgi-bin...?&I=LXCW52&P=7 Also works on any of the above engines.Â
It will also work on OS 61FSR and OS 61VF's sometimes without the addition of the Thrust Washer.
All these engines use a 5/16 prop nut. From .61 to the FT120/160 http://www3.towerhobbies.com/cgi-bin...?&I=LXCT59&P=M
-61 SFÂ Â Â Â Â Â Â Â Â Â -61 RFÂ Â Â Â Â Â Â Â Â Â -60 FPÂ Â Â Â Â Â Â Â Â Â -65 LAÂ Â Â Â Â Â Â Â Â Â -61 FXÂ Â Â Â Â Â Â Â Â Â -61 SX
-61 RX          -61 LX          -61, 65 and 91 VR series          -91 SX-H
-70/91 Surpass                -FT120/160Â
Regards
Either one of these should work for an OS 61 RF rear exhaust.
http://www3.towerhobbies.com/cgi-bin...&I=LXCL44&P=SM
http://www3.towerhobbies.com/cgi-bin...&I=LXCL47&P=SM
This is the replacement drive washer for the following OS engines:
.61 SFN-H w/6B carb                     .61 SFN-H ABC w/6B
.61Â SFÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â .61 SX-H Heli SE
.61 RX-H Heli REÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â .61 RFN-H RC
.61 RFN-H ABC RCÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â .61 RF
The 61SF or 61RF requires this thrust Washer http://www3.towerhobbies.com/cgi-bin...?&I=LXCW52&P=7 Also works on any of the above engines.Â
It will also work on OS 61FSR and OS 61VF's sometimes without the addition of the Thrust Washer.
All these engines use a 5/16 prop nut. From .61 to the FT120/160 http://www3.towerhobbies.com/cgi-bin...?&I=LXCT59&P=M
-61 SFÂ Â Â Â Â Â Â Â Â Â -61 RFÂ Â Â Â Â Â Â Â Â Â -60 FPÂ Â Â Â Â Â Â Â Â Â -65 LAÂ Â Â Â Â Â Â Â Â Â -61 FXÂ Â Â Â Â Â Â Â Â Â -61 SX
-61 RX          -61 LX          -61, 65 and 91 VR series          -91 SX-H
-70/91 Surpass                -FT120/160Â
Regards