Broken pushrod on lightly used Saito 100
#26
Thread Starter
My Feedback: (15)
Join Date: Jun 2004
Location: Mokena,
IL
Posts: 528
Likes: 0
Received 0 Likes
on
0 Posts
RE: Broken pushrod on lightly used Saito 100
Guys,
Anyone know where the factory setting is for the low speed needle valve because it is not stated in the manual? It saids start with HSNV 3 1/2 out from bottom, however it said leave LS at factory settings?
Frank
Anyone know where the factory setting is for the low speed needle valve because it is not stated in the manual? It saids start with HSNV 3 1/2 out from bottom, however it said leave LS at factory settings?
Frank
#28
Senior Member
RE: Broken pushrod on lightly used Saito 100
ORIGINAL: fishingships
If you do-it-yourself, does that kill the warranty? I know Frank's is already out of warranty, but I am just curious.
If you do-it-yourself, does that kill the warranty? I know Frank's is already out of warranty, but I am just curious.
If you can demonstrate knowledge & ability during your contact they will be more than happy to save the added expense of shipping & labor.
#29
Senior Member
RE: Broken pushrod on lightly used Saito 100
ORIGINAL: w8ye
Many times the rocker shaft pivot screws don't want to come out.
Many times the rocker shaft pivot screws don't want to come out.
Make sure that you use a good qualility screw driver & have the engine secured in a vice. A bit of assistance W/a pair of channel Locks will help.
#31
Senior Member
Join Date: Dec 2003
Location: Buckeye,
AZ
Posts: 272
Likes: 0
Received 0 Likes
on
0 Posts
RE: Broken pushrod on lightly used Saito 100
I have a Sato 100 with a perry pump, probably 400+ flights, adjusted the valves once. I run a15x4 prop, it will hover, but not really well in a Goldberg Decathlon. RPMs are 9500 to 9800 on the ground, and as stated earlier, about another thousand in the air, often sounds like the tips of the APC prop are going supersonic. I use high oil content heli fuel, sometimes up to 30 % nitro. Now I am going to have to "knock wood," it really runs great. I have a Sato 180 that I have never been able to make run right and I have had some real guru's look at it and tune it. Came with a bad plug which really threw us off at the start. The damn thing just quits at the most inopertune time. I may use it as a boat anchor. wallace.tharp
#33
Senior Member
RE: Broken pushrod on lightly used Saito 100
Wallace has anyone checked the cam timing or had the cam cover off? Ihave seen a lot of Saitos with damaged cams for one reason or another.
#34
Senior Member
Join Date: Dec 2003
Location: Buckeye,
AZ
Posts: 272
Likes: 0
Received 0 Likes
on
0 Posts
RE: Broken pushrod on lightly used Saito 100
ORIGINAL: jeffie8696
Wallace has anyone checked the cam timing or had the cam cover off? I have seen a lot of Saitos with damaged cams for one reason or another.
Wallace has anyone checked the cam timing or had the cam cover off? I have seen a lot of Saitos with damaged cams for one reason or another.
#35
RE: Broken pushrod on lightly used Saito 100
ORIGINAL: wallace.tharp
I have a Sato 100 with a perry pump, probably 400+ flights, adjusted the valves once. I run a15x4 prop, it will hover, but not really well in a Goldberg Decathlon. RPMs are 9500 to 9800 on the ground, and as stated earlier, about another thousand in the air, often sounds like the tips of the APC prop are going supersonic. I use high oil content heli fule, sometimes up to 30 % nitro. Now I am going to have to ''knock wood,'' it really runs great. I have a Sato 180 that I have never been able to make run right and I have had some real guru's look at it and tune it. Came with a bad plug which really threw us off at the start. The damn thing just quits at the most inopertune time. I may use it as a boat anchor. wallace.tharp
I have a Sato 100 with a perry pump, probably 400+ flights, adjusted the valves once. I run a15x4 prop, it will hover, but not really well in a Goldberg Decathlon. RPMs are 9500 to 9800 on the ground, and as stated earlier, about another thousand in the air, often sounds like the tips of the APC prop are going supersonic. I use high oil content heli fule, sometimes up to 30 % nitro. Now I am going to have to ''knock wood,'' it really runs great. I have a Sato 180 that I have never been able to make run right and I have had some real guru's look at it and tune it. Came with a bad plug which really threw us off at the start. The damn thing just quits at the most inopertune time. I may use it as a boat anchor. wallace.tharp
Ken