Hydro Junkie

Too bad Rich is shutting down his parts business as far as the Pitts is concerned. After exchanging PMs, I sent him payment and, to my surprise, received my parts in less than a week. Doesn't get any better than that but, unfortunately, I need to find landing gear to fit as well as obtain an engine. I've already decided to go with a DA-50 for power so does anyone have any ideas on what to use for the landing gear?

rgunder

Thanks for the kind words Hydro Junkie!

I recommend that you check out the existing options at TNT landing gear: http://tntlandinggear.com/

Rich

zeemanjr

Hi can someone please send me a copy of these plans and also the cut file as Id like to build this beautiful plane thanks.
My email address is [email protected]
Regards,
Pete.

fflyerm

Hi all,
could someone please send me the CAD Files?
[email protected]

thx & regards,
Michael

eromeros

Hello

I have one kit I'm willing to sell

Kit includes All formers and Ribs, Cowl, Wheel Pants, alluminum landing gear, alluminum wing struts, canopy and printed plans.
This was purchased directly from Gundersonaerodesign.com when it was still in bussiness.

Required to complete is all stock stringers and sheetting along with all the electronics and miscelaneous stuff.

Kit is beatifully laser cut.

Been sitting collecting dust for a while so I thought someone else could enjoy it.

If interested PM me.

Regards

Elias

fouxmaclaud

Hello,

Can you send me the map Pitts?

Thank you!

packocrayons

I checked the first few pages and got lazy, is there a new link to where the PDF plans are?

tagir86

Hi, I would like to build this sweet plane too, it would be pleasure if somebody send my detailed plans, thnx!

[email protected]

grover1

you have mail

nitro wing

My Feedback: (1)

I would like to join this list and have a set of plans, any building notes??

Thanks
[email protected]

packocrayons

I'm in for a set too.
[email protected]
Thanks!

do335a

All you guys looking for plans files, you should know that a while back there were plans and short kits offered.

About late last summer or fall as I recall -last year in any case, the plans owner/short kit builder sent an email to all of us on his email list saying sayonara - no more Pitts. End of the trail. No more anything.

Prior to that, plans were readil and freely available from him.

So those who's got, got and those who don't, don't.

I had the plans until a computer wipe out fixed that problem. So now I'm in the same boat as the rest of you.

As I recall, there are also a couple of videos on You Tube of a chap flying his copy of the plane with a 50cc engine.

nitro wing

My Feedback: (1)

thanks for updating

Bob Howard

My Feedback: (2)

The plans are on post 726 of this thread

grover1

[b]I have sent out over 20 emails with the Plans and Manual's for this plane and have only got "1" yes 1 thank you .
So I will not be sending any more .

w4mwk

My Feedback: (1)

Grover,
I do apologize! I should have sent this to you sooner "Thank You" for the Plan's and all you have done to make it possible for so many to have the opportunity to have the plans for the spirit of Pitts M12 Designed by Bernard Burton and maybe build this beautiful aircraft.
Thank You Again,
Mike

grover1

You are welcome Mike and you did say thanks before in your email
Greg

nitro wing

My Feedback: (1)

Greg
I did respond to a PM, but had not received any mail with attachments, maybe this had happened to others too??

w4mwk

My Feedback: (1)

Nitro Wing,

The plans are on post 726 of this thread! They are in pdf format, "Four files"

Hope you find thrm OK.
Mike

WALKERS210-RCU

My Feedback: (36)

Due to health issues I quit building and flying my planes a few years back. This past Christmas I spent money for a plotter that I have wanted for a number of years that would allow me to print out plans. A surprise bonus to the software I bought has the ability to import the PDF format plans and print them out. So far I still need more work to learn all that is needed to print a complete sheet but each time I have a go at it I am getting better. Also I can save the PDF format to DXF format but have yet tried it out to see if the drawings come out 100%. After I feel comfortable and not just wasting time I will try to help others out.

nitro wing

My Feedback: (1)

thanks to all that had positive input and that had files to share.

w4mwk

My Feedback: (1)

Grover,
A quick question. Do you or maybe someone reading this tread happen to know what brand and size Landing Gear the Spirit Of Pitts M12 was designed to use? I've looked over the plans and instruction's! Didn't see a lot of info on the topic.
Regards,
Mike

eromeros

w4mwk
Give me some time and I'll send you pics and measurements of the landing gear.

Elias
[/b]