PatternFlyer

My Feedback: (182)

E-Flite announced the Splendor BNF basic.

http://www.e-fliterc.com/Products/De...rodId=EFL10250

Good looking. A little hybrid with large elevators.

Comes with new 6ch AS3X integrated receiver.
6S pack needed.

I will definitely try a little before replacing the receiver with non-AS3X rx.

Ihncheol

TonyF

My Feedback: (92)

I've been playing with the AS3X system in the VisionAire and in another smaller electric model. You can turn the gains to zero to turn the stabilization off if you want.

PatternFlyer

My Feedback: (182)

Hi, Tony,

I was told by a member at RCGroups (he purchased the VisionAir) that he couldn't turn off the AS3X (he said that he dialed it down to lowest possible setting).
I just got the new AS3X receiver. Got to play with it a little.

How is the VisionAire? Video of QQ flying at the AMA convention wasn't showing much.

Back to Splendor.
Have you seen one flying?

Ihncheol

Matt_McCarty

My Feedback: (2)

Ihncheol,

See the videos below of the VisionAire. The AMA venue was pretty small and didn't allow for too much.

http://www.youtube.com/watch?v=pvJ4T76rP6g
http://www.youtube.com/watch?v=FEZ2CGJooIw

The Carbon-Z Splendor is amazing. I have seen it fly with and without gyros; I will have one soon and can report back. It's a very capable airplane.

Ryan Smith

My Feedback: (25)

Sorry,

Matt was signed in on my computer and I didn't check before posting. That was me posting above.

PatternFlyer

My Feedback: (182)

Ryan,

when will the video of the Splendor be online?

Thanks,

Ihncheol

Ryan Smith

My Feedback: (25)

It's up now on the E-flite website.

http://www.e-fliterc.com/Products/De...250#quickMedia

Matt_McCarty

My Feedback: (2)

Hello Ihncheol, ( actually Matt this time )

To turn the AS3X "off" on the AR635 the gain on all three axis and in gear position 1 and 0 must be set to zero gain. This is shown by no blinking Aileron, elevator, and rudder LEDs. The manual goes into more detail on how to adjust.

I was lucky enough to fly an early prototype when in Asia late Sept of 2012..... and this plane flys amazing. I was also able to fly the sample with both an AR600 and an AR635......it's simple.....I'm buying one.

Best Regards,

Matt McCarty

TonyF

My Feedback: (92)

So far I really like the VisionAire. Very nicely engineered and it flies well. Only thing I think is that I'd like a bit more power. But then I've never flown an overpowered model!

I can't say anything more about the Splendor other then it looks good. I'm not involved in any way with development or testing so when you see it that's when I do. Hope to get one when they become available.

mickvk

My Feedback: (1)

Channel 5 (gear) turns stabilization on/off

F.Imbriaco

My Feedback: (56)

This is an interesting ship.

Too bad it requires 6s.

I already have a large and growing of supply of 5S packs.

This ship would be great for some off-season / small field flying.

F.Imbriaco

My Feedback: (56)

The Carbon Z Splendor is an interesting ship.

Too bad it requires 6s.

I already have a large and growing of supply of 5S packs.

This ship would be great for some off-season / small field flying.

mickvk

My Feedback: (1)

a 15% voltage change isn't insurmountable. You could add a little prop pitch or diameter to make up for it.

All I had was 3S 5000mah packs and I'm making them work... I'm very pleased with performance.

piroflip2

no it doesn't!!!!!!!!!

mickvk

My Feedback: (1)

I stand corrected. When I first started using it, effectively that's what I observed... It seemed to turn stabilization on/off. Looking at the book it seems that it changes from F3A mode to 3D mode. The table laying out the values is here: