Motor cutting out.
#1
Senior Member
Thread Starter
Join Date: Feb 2003
Location: Clifton Heights,
PA
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
Motor cutting out.
Fired up the Rappy 50 after a fly bar fix. Had about 30 flights on her.
Started right up, warmed her up ,idled fine.
Spooled her up and went into hover.
10 seconds in and 10 feet up she cut out and went to idle. White knuckle landing.
Checked glo plug,glowing bright, checked in line fuel filter,clean.
Started right back up, tried again, spooled her up again started to hover about half stick, cut back to idle ?
Starts and Idles just fine, spools up, starts to hover and cuts back to idle.
I put bricks on the skids to hold her down to the ground,reved her up to mid stick, went back to idle.
Any thoughts ?
Thanks
Started right up, warmed her up ,idled fine.
Spooled her up and went into hover.
10 seconds in and 10 feet up she cut out and went to idle. White knuckle landing.
Checked glo plug,glowing bright, checked in line fuel filter,clean.
Started right back up, tried again, spooled her up again started to hover about half stick, cut back to idle ?
Starts and Idles just fine, spools up, starts to hover and cuts back to idle.
I put bricks on the skids to hold her down to the ground,reved her up to mid stick, went back to idle.
Any thoughts ?
Thanks
#5
My Feedback: (11)
RE: Motor cutting out.
Eh...I been messing with this RC stuff a year or two
It was going into fail safe and pulling the throttle to idle. The pack can't hold a load, start working the sticks and the voltage drops off then the throttle servo went to idle.
When the load was removed the voltage came back up and it looked like the battery was ok.
It was going into fail safe and pulling the throttle to idle. The pack can't hold a load, start working the sticks and the voltage drops off then the throttle servo went to idle.
When the load was removed the voltage came back up and it looked like the battery was ok.
#6
Senior Member
Thread Starter
Join Date: Feb 2003
Location: Clifton Heights,
PA
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
RE: Motor cutting out.
Ha ! Thats funny.
Just charged it over night.
Looks like I an getting a new RX batt. Don`t ever want that feeling again ! Not worth it.
Thanks for all your help.
Just charged it over night.
Looks like I an getting a new RX batt. Don`t ever want that feeling again ! Not worth it.
Thanks for all your help.
#8
Senior Member
Thread Starter
Join Date: Feb 2003
Location: Clifton Heights,
PA
Posts: 277
Likes: 0
Received 0 Likes
on
0 Posts
RE: Motor cutting out.
Was gonna order a new Nicad to replace the old one,is there something better ?
I only have the one Futaba charger that that does the RX and TX.
If I changed the rx to some thing differant I would have to change the TX as well ?
I only have the one Futaba charger that that does the RX and TX.
If I changed the rx to some thing differant I would have to change the TX as well ?
#9
Senior Member
Join Date: Apr 2007
Location: Schweinfurt, GERMANY
Posts: 172
Likes: 0
Received 0 Likes
on
0 Posts
RE: Motor cutting out.
I have the B6T 2 IN 1..I love it. Gives me an indication of the remaining power, glow igniter and good stable power. I’m flying a Raptor 50.
http://www.ronlund.com/rcheli-prod/E...HE50H11-1.html