Go Back  RCU Forums > RC Airplanes > Seaplanes
Reload this Page >

gee bee "islander mark 11

Notices
Seaplanes Aircraft that typically take off and land on water...radio control seaplane discussions are in here.

gee bee "islander mark 11

Old 01-23-2008, 03:02 PM
  #1  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default gee bee "islander mark 11

does anyone have a set of plans for this plane?
Falcon
Old 03-21-2013, 09:09 AM
  #2  
Butcherbird58
Junior Member
 
Join Date: Mar 2013
Location: Plano, TX
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

did you ever find plans for the Gee Bee Islander?I am looking as well
Old 03-21-2013, 09:19 AM
  #3  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default RE: gee bee


ORIGINAL: Butcherbird58

did you ever find plans for the Gee Bee Islander? I am looking as well
No never did,,,,,,,
Old 03-22-2013, 03:55 AM
  #4  
Butcherbird58
Junior Member
 
Join Date: Mar 2013
Location: Plano, TX
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

Guess I will need to reverse engineer myself then, know from the spec. the wing span and area, constant cord wing is easy, empenagevolume and placement isproportional to wing area, any ideas on how to bond to the Gee Bee float, everything I read on floats indicates that a sharp edge is needed at the step to create the air pocket.
Old 03-22-2013, 04:11 AM
  #5  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default RE: gee bee


ORIGINAL: Butcherbird58

Guess I will need to reverse engineer myself then, know from the spec. the wing span and area, constant cord wing is easy, empenage volume and placement is proportional to wing area, any ideas on how to bond to the Gee Bee float, everything I read on floats indicates that a sharp edge is needed at the step to create the air pocket.
Back in the day., They used some kind of rubber glue,,Today I would use " Goo"glue, its a mess to work with (cant be cleaned up)Iwould drill holes in the float where the fuse attached..I would do it with a wooden float so this would not be a issue.....also I would do it as a e-flight..the origonal had a flat bottom wing..i new the guy(Tom Rigensky)that flew the planes for the guys that made them. He flew with a few of us on Bantom lake in Ct.I hated to hear it when it landed,,we called it sounding like a woofel ball batkeep me in the loop on your quest,,,
Old 03-23-2013, 04:30 PM
  #6  
aspeed
 
aspeed's Avatar
 
Join Date: Jul 2011
Location: Ruthven, ON, CANADA
Posts: 3,460
Likes: 0
Received 7 Likes on 7 Posts
Default RE: gee bee

Is this one? It said Gee Bee on the float, but I have no idea what the plane is called any more.
Attached Thumbnails Click image for larger version

Name:	Ig11151.jpg
Views:	238
Size:	141.9 KB
ID:	1865629   Click image for larger version

Name:	Ql33761.jpg
Views:	148
Size:	150.0 KB
ID:	1865630  
Old 03-24-2013, 04:02 AM
  #7  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default RE: gee bee

Not sure how to post
Attached Images       
Old 03-24-2013, 06:23 AM
  #8  
Butcherbird58
Junior Member
 
Join Date: Mar 2013
Location: Plano, TX
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

Thanks aspeed, that is the GeeBee Islander,  wouldn't by any chance have a set of the plans would U?  The top view photo is very helpful   any way I could get you to send a direct side view photo,   I can scale from these knowing the length of the float and recreate,  would be helpful to know where the step is relative to the C.G.  

falcon6667, that looks like a corner of a plans sheet,  I could not enlarge the view clearly,  if you have a set of plans could I get a copy ?
Old 03-24-2013, 06:30 AM
  #9  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default RE: gee bee


ORIGINAL: Butcherbird58

Thanks aspeed, that is the GeeBee Islander, wouldn't by any chance have a set of the plans would U? The top view photo is very helpful any way I could get you to send a direct side view photo, I can scale from these knowing the length of the float and recreate, would be helpful to know where the step is relative to the C.G.

falcon6667, that looks like a corner of a plans sheet, I could not enlarge the view clearly, if you have a set of plans could I get a copy ?
Sadly its all I have, It was e-maled to me yesterday by a buddie from back in the day that rembered the history on the plane,,I think if we keep talking about it one will apear Ill att toms note to me...,,,,,,,,,,,,,,,,,,,,,,,,
Port.
I remember the plane.. It was designed by Don ???? who was from Longmeadow (Springfield) MA.. It was a Gee Bee kit.. Don ??? owned the Gee Bee Products company(I think) It used a blow molded plastic float for the main body.. The plastic was (I think) polypropylene, like used for gallon milk jugs.. They didn't work very well because they didn't have sharp chines.. Jimmy and Ed and I thought they were junk because they worked so poorly.. I think the float was 33 inches long..

Don used to run the float fly event at Brimfield MA.. I think he may have buddied up with Tom Roginski to make the Tom Cat kits that were junk!! I think he had a couple of designs published in one of the model magazines.. (Not the Islander though)

I think I found the same RC Groups ad that you got the pictures from.. The guy (NERO 1156) wanted $125 for the kit last September.. I don't know if he sold it or not.. I did find a phone number for Gee Bee Products, but I am not sure if it's any good, or if Don ??? is still alive!! anyway, its: 413-782-3872

I also found a Gee Bee Products ad in one of my old files.. I'll see if I can make a copy to e-mail to you.. Otherwise I'll snail mail a copy..

i have no idea where you could find a set of plans.. Maybe one of the guys on RC Universe or RC groups might be able to help.. There seemed to be a lot of back and forth posting about the Islander there..

TOM
Old 03-24-2013, 07:57 AM
  #10  
aspeed
 
aspeed's Avatar
 
Join Date: Jul 2011
Location: Ruthven, ON, CANADA
Posts: 3,460
Likes: 0
Received 7 Likes on 7 Posts
Default RE: gee bee

Sorry I don't have plans either.  The float is about 32" long without the rudder, wing is 49 1/2" x 9 1/2"  The booms are 13" apart, and the stab is 19 3/4 x 5" with the centre section for the elevator being cut out 2". The pointed part of the step is about 2" behind the LE of the wing.  I thought the plane was a Mallard.  I got it at a swap meet maybe 20 years ago when I had access to a pond but no field.  I picked up 4 seaplanes then, having bad luck with the Herr Aquastars electric and nitro.  Now I can't get on a pond but have a field.  I never tried the Islander yet.  It is kind of tight for the servos and I never finished hooking things up.  It may have been flown, I noticed some tailweight in it.  You never know what has happened with swap meet stuff, always thrilling and/or disappointing it seems.  The wing, rudder and booms are one piece, and the fuse/float and steering rudder are the other piece.  I yahooed it yesterday to see what mine was called and saw one sold on ebay for $81, in kit form.  I couldn't read the specs on the box, it wasn't too clear, but I read in a magazine that is is for a .19 to .25.  I have an old OS .29 Speed on mine. Maybe I can get more pics. a little later.  I think if I was making any more float planes, I would make a foam wing, just because it floats.
Old 03-24-2013, 12:42 PM
  #11  
aspeed
 
aspeed's Avatar
 
Join Date: Jul 2011
Location: Ruthven, ON, CANADA
Posts: 3,460
Likes: 0
Received 7 Likes on 7 Posts
Default RE: gee bee



pics

Attached Thumbnails Click image for larger version

Name:	Lj23857.jpg
Views:	100
Size:	86.6 KB
ID:	1865982   Click image for larger version

Name:	Xs58475.jpg
Views:	104
Size:	71.5 KB
ID:	1865983   Click image for larger version

Name:	Bh94707.jpg
Views:	106
Size:	69.1 KB
ID:	1865984  
Old 03-24-2013, 12:53 PM
  #12  
aspeed
 
aspeed's Avatar
 
Join Date: Jul 2011
Location: Ruthven, ON, CANADA
Posts: 3,460
Likes: 0
Received 7 Likes on 7 Posts
Default RE: gee bee

pic
Attached Thumbnails Click image for larger version

Name:	Us54821.jpg
Views:	102
Size:	103.5 KB
ID:	1865985   Click image for larger version

Name:	Gb89175.jpg
Views:	106
Size:	94.2 KB
ID:	1865986  
Old 03-24-2013, 12:59 PM
  #13  
aspeed
 
aspeed's Avatar
 
Join Date: Jul 2011
Location: Ruthven, ON, CANADA
Posts: 3,460
Likes: 0
Received 7 Likes on 7 Posts
Default RE: gee bee

I think I would rather have a Seawind or Seamaster rather than this one myself.
Attached Thumbnails Click image for larger version

Name:	Rp42469.jpg
Views:	101
Size:	70.0 KB
ID:	1865987   Click image for larger version

Name:	Ez82647.jpg
Views:	118
Size:	66.1 KB
ID:	1865988  
Old 05-20-2013, 07:54 PM
  #14  
PeterC
 
Join Date: May 2002
Location: Edmonton, AB, CANADA
Posts: 499
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

Interesting plane this! I had the Mallard which had a fuselage rather than the twin booms. The plane is only three channel and was powered with a OS 25. Mine flew nicely but because of the Gee Bee floats would not take off unless there was some chop on the water.
I used to get kids to throw stones in front of the plane when the water was calm to create some ripples. The tip floats were humongous, I once heard them refered to as inverted Dixie Cups. I have the plans for the Mallard which is exactly the same except for the twin booms. I kinda liked the twin boom look. It reminds me of an old Sikorsky.
Peter
Old 05-21-2013, 04:20 AM
  #15  
Butcherbird58
Junior Member
 
Join Date: Mar 2013
Location: Plano, TX
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

Peter,
Would you allow me to copy your plans and return them 2U?
Old 05-21-2013, 05:35 AM
  #16  
PeterC
 
Join Date: May 2002
Location: Edmonton, AB, CANADA
Posts: 499
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

PM sent.
Peter
Old 06-04-2013, 02:29 PM
  #17  
PeterC
 
Join Date: May 2002
Location: Edmonton, AB, CANADA
Posts: 499
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

Actually Falcon, you are right about using "Goo". I use automotive goo to stick plastic and fiberglass parts to balsa and it works well.
As far as clean up is concerned just let it dry and then roll it off with your thumb. The original used contact cement to join the fuselage to the hull. A leather strip was then glued to the seam to further seal it. You could try weather strip adhesive as it looks and smells the same as the old contact cement.
Peter
Old 07-22-2013, 07:16 AM
  #18  
snolord1
Junior Member
My Feedback: (7)
 
snolord1's Avatar
 
Join Date: May 2004
Location: chicopee, MA
Posts: 16
Likes: 0
Received 0 Likes on 0 Posts
Default RE: gee bee

Someone on regroups has a gee bee Bipe
Old 09-27-2013, 09:57 AM
  #19  
Steve in VA
Junior Member
 
Join Date: Sep 2013
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I have a set of plans for the Islander - I'm happy to lend them for copying.
Old 09-27-2013, 12:17 PM
  #20  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default

Originally Posted by Steve in VA
I have a set of plans for the Islander - I'm happy to lend them for copying.
I would reaslly like a set of those...what will it take to get them?
Old 09-27-2013, 06:54 PM
  #21  
Steve in VA
Junior Member
 
Join Date: Sep 2013
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I'm new to this forum, so correct me if I'm wrong, but if you pm me an address I'll pop them in the post. Just promise to return them when you've copied them!
I flew mine for many years, I had no trouble getting it off the water, and as I got more experienced I'd have a blast scooting around on the step at high speed. The twin rudders are out of the prop wash so the addition of the water rudder helps a lot in slow speed taxiing (I put the water rudder on the left stick with a micro servo). I flew it with a .29 - more then enough power as a sea plane but only adequate with the wheels on.
Old 09-29-2013, 04:51 PM
  #22  
Butcherbird58
Junior Member
 
Join Date: Mar 2013
Location: Plano, TX
Posts: 11
Likes: 0
Received 0 Likes on 0 Posts
Default

Steve,
Thank You for your offer, i got a set of plans for the Malard, single tail, and I can reverse engineer from the photos sent in the foram, thank U again
Old 09-30-2013, 03:57 AM
  #23  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default

Originally Posted by Steve in VA
I have a set of plans for the Islander - I'm happy to lend them for copying.
did you get my "pm"?
Old 09-30-2013, 10:01 AM
  #24  
Falcon6667
Thread Starter
 
Falcon6667's Avatar
 
Join Date: Sep 2007
Location: Elberton, GA
Posts: 338
Received 0 Likes on 0 Posts
Default

Originally Posted by Steve in VA
I have a set of plans for the Islander - I'm happy to lend them for copying.
>>>>>OUTSTANDING
Old 10-01-2013, 06:43 PM
  #25  
Steve in VA
Junior Member
 
Join Date: Sep 2013
Posts: 4
Likes: 0
Received 0 Likes on 0 Posts
Default

I'm just sorry I did not see your request earlier. No rush on their return - whenever you have time. You've inspired me to dust off my Islander and try and get it back into the air. Thanks! If you're still in touch with the test pilot please forward my thanks to him/her for a lovely model and for the many hours of enjoyment I've had flying it.

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.