PLease HELP!!
#1
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
PLease HELP!!
I don't know where to post this?I really could use some help with this, I know its old but its my only toy!It's a E-Flite Blade CX, yes the original.Ok, I am irritated now! Havent flown this in over 3 years. So I ordered a new battery and some new blades. Got them today, charged the battery, put it in and turn on remote and man the thing started wigging out! Started spinning off and on high speed then low then little twitches, servo's wigging out to?So anyone have any ideas why? Its FM transmitter, so is it possible getting interference from something? Or is it cause the battery is a 900mAh instead of original 800mAh?And doesn't respond to the remote.
#3
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
ORIGINAL: Big Alice
Did you remember to let the heli set still and level after you plugged the battery in so the gyro stabilises?
Did you remember to let the heli set still and level after you plugged the battery in so the gyro stabilises?
#4
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
Well I let it sit a while, the red led is suppose to turn green. It will turn Green, then flashing Red, then steady red, then back to green, flashing green. It doesn't stay green or red very long keeps bouncing around in colors, and while that's going, servos and blades are going crazy! So you think the 4 in 1 is shot? If so, I guess I am screwed cause I cant find one anywhere online.
#5
RE: PLease HELP!!
I think they were about 50 bucks new. I'd just get something like this and fly one and use the other for parts. Or watch ebay. you see them once in a while.
http://www.ebay.com/itm/blade-cx-Rtf...b#ht_220wt_815
#6
Senior Member
My Feedback: (2)
Join Date: Nov 2002
Location: Jackson, MI
Posts: 2,102
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
Don't move the heli for about 5 seconds after plugging in the battery.
Also, always turn on the transmitter first, then plug in the heli battery. When done flying, it's the reverse; unplug the heli battery, then shut off the transmitter.
#8
Senior Member
My Feedback: (2)
Join Date: Nov 2002
Location: Jackson, MI
Posts: 2,102
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
Does anyone think I could be having radio wave interference? It is a FM transmitter.What things could cause interference?
Unlikely, unless someone else is nearby (about 1/2-mile) on your frequency. Radios don't go bonkers just from setting around. Are the transmitter batteries fresh? Are you sure it's the right radio & freq?
Another device emitting RF, like a lawn mower, string trimmer, ham operator using illegal power amplifiers, etc., could cause interference. Cell phones, especially when ringing or ending calls, have been known to interfere with 2.4Ghz RC radios. Is there any possibility your receiver got wet at some point, or has been dropped?
#9
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
ORIGINAL: eddieC
Does anyone think I could be having radio wave interference? It is a FM transmitter.What things could cause interference?
Unlikely, unless someone else is nearby (about 1/2-mile) on your frequency. Radios don't go bonkers just from setting around. Are the transmitter batteries fresh? Are you sure it's the right radio & freq?
Another device emitting RF, like a lawn mower, string trimmer, ham operator using illegal power amplifiers, etc., could cause interference. Cell phones, especially when ringing or ending calls, have been known to interfere with 2.4Ghz RC radios. Is there any possibility your receiver got wet at some point, or has been dropped?
#10
Senior Member
My Feedback: (2)
Join Date: Nov 2002
Location: Jackson, MI
Posts: 2,102
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
Hmm, I was told by others, such things like Microwaves and other appliances, could interfere with the frequency?
That's correct, I was only giving a few examples. Was ANYTHING else running nearby? Your neighbor's microwave wouldn't cause interference, you'd have to be on top of the source.
#11
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
ORIGINAL: eddieC
Hmm, I was told by others, such things like Microwaves and other appliances, could interfere with the frequency?
That's correct, I was only giving a few examples. Was ANYTHING else running nearby? Your neighbor's microwave wouldn't cause interference, you'd have to be on top of the source.
#12
Senior Member
My Feedback: (2)
Join Date: Nov 2002
Location: Jackson, MI
Posts: 2,102
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
Only things I can imagine is your transmitter or receiver has been damaged somehow. If the servos are jumping, they are receiving some kind of signal. Try shutting off the transmitter and note if the behavior changes. Do the motors run, and rotors spin?
#14
Senior Member
My Feedback: (2)
Join Date: Nov 2002
Location: Jackson, MI
Posts: 2,102
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
Odd behavior for sure.
Is the antenna on the heli secure? They're fragile.
Tap on the 4-in-1 unit with a pencil eraser to see if things jump. Beyond that, I'd send it in or have an LHS check it out.
#15
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
ORIGINAL: eddieC
Odd behavior for sure.
Odd behavior for sure.
Is the antenna on the heli secure? They're fragile.
Tap on the 4-in-1 unit with a pencil eraser to see if things jump. Beyond that, I'd send it in or have an LHS check it out.
And what is LHS?
#18
Senior Member
Join Date: Sep 2010
Location: OR
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
The Blade CX2 was my first heli!
The receiver is not getting any signal.
Check your crystals, check your antennas, check your wiring.
Yes, I still fly megahertz radios, and I see the same thing happen when I forget to turn my transmitter on first....
The receiver is not getting any signal.
Check your crystals, check your antennas, check your wiring.
Yes, I still fly megahertz radios, and I see the same thing happen when I forget to turn my transmitter on first....
#19
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
ORIGINAL: ssautter
The Blade CX2 was my first heli!
The receiver is not getting any signal.
Check your crystals, check your antennas, check your wiring.
Yes, I still fly megahertz radios, and I see the same thing happen when I forget to turn my transmitter on first....
The Blade CX2 was my first heli!
The receiver is not getting any signal.
Check your crystals, check your antennas, check your wiring.
Yes, I still fly megahertz radios, and I see the same thing happen when I forget to turn my transmitter on first....
#20
Senior Member
My Feedback: (2)
Join Date: Nov 2002
Location: Jackson, MI
Posts: 2,102
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
The receiver is not getting any signal.
If it weren't getting any signal, the servos wouldn't jump around. It's not getting a good signal, or not decoding it properly.
Sometimes a light tap on the receiver or trans will reveal some signs.
#21
Junior Member
Thread Starter
My Feedback: (1)
Join Date: Jun 2013
Location: eldon, MO
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
ORIGINAL: eddieC
The receiver is not getting any signal.
If it weren't getting any signal, the servos wouldn't jump around. It's not getting a good signal, or not decoding it properly.
Sometimes a light tap on the receiver or trans will reveal some signs.
#22
My Feedback: (33)
Join Date: Jan 2002
Location: Granbury, TX,
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
Have you checked all your connections, i.e. servos and anything else that plugs in? If the heli has been sitting for three years things might have come loose or there might be some corrosion. You could try unplugging and plugging a few times to make sure everything is making good contact. Good luck!
#23
Senior Member
Join Date: Sep 2010
Location: OR
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
RE: PLease HELP!!
ORIGINAL: eddieC
The receiver is not getting any signal.
If it weren't getting any signal, the servos wouldn't jump around. It's not getting a good signal, or not decoding it properly.
Sometimes a light tap on the receiver or trans will reveal some signs.
And, many older systems don't incorporate failsafe, to return servos to a preset position.
#24
Moderator
RE: PLease HELP!!
Have you considered calling Blade support? Yes, it's an old product, but their tech guys are pretty good. I wouldn't expect warranty parts to be shipped for free, but you may be surprised how quickly they can solve your problem and how accommodating they may be on getting you running again.