Central NEW YORK boaters
07-14-2013, 01:58 PM
#3903
Senior Member
Join Date: Jun 2011
Location: West Henrietta , NY
Posts: 180
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Neil, take care of yourself. Hope the implant works out. Missed you at the pond today, wasn't the same. Ran the JAE 21 with the new NR today, showed promise. Glad to get rid of the GO Motor. Will try and sell it - maybe someone who has one would like a backup. Also tested the 20 Mono with the changed head clearance - went good. Finally the boats are showing some promise. Good luck to all at Elmira next weekend. Hope to have the twin at Stony Pond the weekend of July 27th.
T&C
07-15-2013, 07:39 AM
#3905
Thread Starter
Join Date: Feb 2006
Location: Baldwinsville,
NY
Posts: 3,055
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: Proboat 772
Neil,
Hope the device gives you relief. I didn't realize you had a serious back problem..
Dick T
Neil,
Hope the device gives you relief. I didn't realize you had a serious back problem..
Dick T
07-15-2013, 01:57 PM
#3906
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Boy scout update for this weekend. They are leaving Sunday at 10:00am, so anyone can run boats on Sunday. The pond will be closed to rc boats Friday 6 pm to Sunday 10 am. Get the word out to any non RCU guys. Thanks.
07-30-2013, 06:26 AM
#3908
Thread Starter
Join Date: Feb 2006
Location: Baldwinsville,
NY
Posts: 3,055
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Dick
My Whiplash has been reworked. I have the right Dia stuffing tube installed. All is good. Adding a Carbon fiber layover inside the engine bay. Covering up most of that glob of resin.
Craig
my .21 CMB Vac has been replaced by a NOVA ROSSI 35+ Bill's old/new to me engine. never started YET. So I got to break her in. The Vac has low piston sleeve compression. I can rotate the crank over TDC easy. That's not right for a new engine. How can I loose compression on a new engine. ???
Bill
My cat has a rebuilt .67 CMB and I dropped the strut down 3/16 to solve the blow over issues within +-1/16 . We did have strong winds the day I tested. All ran good except the .21 Vac
Rick where are you?
My Whiplash has been reworked. I have the right Dia stuffing tube installed. All is good. Adding a Carbon fiber layover inside the engine bay. Covering up most of that glob of resin.
Craig
my .21 CMB Vac has been replaced by a NOVA ROSSI 35+ Bill's old/new to me engine. never started YET. So I got to break her in. The Vac has low piston sleeve compression. I can rotate the crank over TDC easy. That's not right for a new engine. How can I loose compression on a new engine. ???
Bill
My cat has a rebuilt .67 CMB and I dropped the strut down 3/16 to solve the blow over issues within +-1/16 . We did have strong winds the day I tested. All ran good except the .21 Vac
Rick where are you?
07-30-2013, 06:34 AM
#3909
Member
Join Date: Sep 2011
Location: Rochester, NY
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Wanted to say I had a good time down at Stony Pond on Saturday. Thank you Joe, Tom and Cindy for the help with the boats. Thanks Craig for letting me come down. This group makes this hobby so much more fun then playing around by myself. I hope to be down more than once nexy year. -Eric
07-30-2013, 06:38 AM
#3910
Senior Member
RE: Central NEW YORK boaters
ORIGINAL: advanced builder
Dick
My Whiplash has been reworked. I have the right Dia stuffing tube installed. All is good. Adding a Carbon fiber layover inside the engine bay. Covering up most of that glob of resin.
Craig
my .21 CMB Vac has been replaced by a NOVA ROSSI 35+ Bill's old/new to me engine. never started YET. So I got to break her in. The Vac has low piston sleeve compression. I can rotate the crank over TDC easy. That's not right for a new engine. How can I loose compression on a new engine. ???
Bill
My cat has a rebuilt .67 CMB and I dropped the strut down 3/16 to solve the blow over issues within +-1/16 . We did have strong winds the day I tested. All ran good except the .21 Vac
Rick where are you?
Dick
My Whiplash has been reworked. I have the right Dia stuffing tube installed. All is good. Adding a Carbon fiber layover inside the engine bay. Covering up most of that glob of resin.
Craig
my .21 CMB Vac has been replaced by a NOVA ROSSI 35+ Bill's old/new to me engine. never started YET. So I got to break her in. The Vac has low piston sleeve compression. I can rotate the crank over TDC easy. That's not right for a new engine. How can I loose compression on a new engine. ???
Bill
My cat has a rebuilt .67 CMB and I dropped the strut down 3/16 to solve the blow over issues within +-1/16 . We did have strong winds the day I tested. All ran good except the .21 Vac
Rick where are you?
07-30-2013, 07:02 AM
#3911
Thread Starter
Join Date: Feb 2006
Location: Baldwinsville,
NY
Posts: 3,055
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
Yes real work comes before playtime. Rick we just misses your insight. HeliDrop glad to meet you. by the end of the day your hull was moving right along. Any pic can be posted on Ricks Facebook site. https://www.facebook.com/groups/6696...=group_comment
07-30-2013, 03:00 PM
#3912
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: advanced builder
Dick
My Whiplash has been reworked. I have the right Dia stuffing tube installed. All is good. Adding a Carbon fiber layover inside the engine bay. Covering up most of that glob of resin.
Craig
my .21 CMB Vac has been replaced by a NOVA ROSSI 35+ Bill's old/new to me engine. never started YET. So I got to break her in. The Vac has low piston sleeve compression. I can rotate the crank over TDC easy. That's not right for a new engine. How can I loose compression on a new engine. ???
Bill
My cat has a rebuilt .67 CMB and I dropped the strut down 3/16 to solve the blow over issues within +-1/16 . We did have strong winds the day I tested. All ran good except the .21 Vac
Rick where are you?
Dick
My Whiplash has been reworked. I have the right Dia stuffing tube installed. All is good. Adding a Carbon fiber layover inside the engine bay. Covering up most of that glob of resin.
Craig
my .21 CMB Vac has been replaced by a NOVA ROSSI 35+ Bill's old/new to me engine. never started YET. So I got to break her in. The Vac has low piston sleeve compression. I can rotate the crank over TDC easy. That's not right for a new engine. How can I loose compression on a new engine. ???
Bill
My cat has a rebuilt .67 CMB and I dropped the strut down 3/16 to solve the blow over issues within +-1/16 . We did have strong winds the day I tested. All ran good except the .21 Vac
Rick where are you?
07-30-2013, 03:01 PM
#3913
Senior Member
Join Date: Feb 2008
Location: Canandaigua, NY
Posts: 1,754
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: HeliDrop
Wanted to say I had a good time down at Stony Pond on Saturday. Thank you Joe, Tom and Cindy for the help with the boats. Thanks Craig for letting me come down. This group makes this hobby so much more fun then playing around by myself. I hope to be down more than once nexy year. -Eric
Wanted to say I had a good time down at Stony Pond on Saturday. Thank you Joe, Tom and Cindy for the help with the boats. Thanks Craig for letting me come down. This group makes this hobby so much more fun then playing around by myself. I hope to be down more than once nexy year. -Eric
07-30-2013, 07:14 PM
#3915
Join Date: May 2008
Location: Cornwall,
ON, CANADA
Posts: 401
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
ORIGINAL: Joe Petro
With a Dremel...
Joe
ORIGINAL: advanced builder
How can I loose compression on a new engine. ???
How can I loose compression on a new engine. ???
Joe
LOL you picking a our little beaver.
yes it was a good one Joe to bad you can't make it for our event it would have been nice to have you.
07-31-2013, 12:57 PM
#3919
Join Date: May 2008
Location: Cornwall,
ON, CANADA
Posts: 401
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
A little Promo vid for our up coming event.
[youtube]http://www.youtube.com/watch?v=xxFu6UqmHwE&feature=c4-overview&list=UUQlth1s6dPMSxFRYda3MmhA[/youtube]
[youtube]http://www.youtube.com/watch?v=xxFu6UqmHwE&feature=c4-overview&list=UUQlth1s6dPMSxFRYda3MmhA[/youtube]
07-31-2013, 05:26 PM
#3922
Thread Starter
Join Date: Feb 2006
Location: Baldwinsville,
NY
Posts: 3,055
Likes: 0
Received 0 Likes
on
0 Posts
RE: Central NEW YORK boaters
My .21 CMB Vac will be back. Inside a JAE rigger. It's the .45 JAE I want to play with. No-one to race against. Where are all the .45 guys Also Joe I seen a newer version of the .45 with Al Long, up in Hamilton.Ont what's with that???? When did the updated hull come out? Why didn't we get the new stuff. Please come clean. What about the .45 outboard JAE rigger?? Not that I want one. I cant wait to run my .67 SGX now that I found that bad rudder servo. I knew I was a better driver than it showed driving that rigger. Spinout city.
