Go Back  RCU Forums > RC Boats > Speed - RC Gas Boats
Reload this Page >

NOT FOR SALE BUT NEED A VALUE!

Notices
Speed - RC Gas Boats Discuss gas RC boats right here!

NOT FOR SALE BUT NEED A VALUE!

Old 08-06-2007, 10:12 PM
  #1  
HeyRobi
Member
Thread Starter
My Feedback: (3)
 
HeyRobi's Avatar
 
Join Date: Sep 2004
Location: Murfreesboro, TN
Posts: 63
Likes: 0
Received 0 Likes on 0 Posts
Default NOT FOR SALE BUT NEED A VALUE!

THIS IS NOT MINE ITS NOT FOR SALE I DONT EVEN HAVE IT IN MY POSSESION!!! NOT TRYING TO SELL!!!!!!!!!


I have someone wanting to trade me this boat for a helicopter I have listed in the classifieds could someone read the email he sent me and tell me what you think it would be worth!



Hydro sport marine unlimited hydro hull 32" estimate can measure for sure later
Hull is carbon Fiber / Deck is Fiberglass
Running gear manufacturer unknown, but was used exclusively in the racing circuit in Dallas texas
Octura metal prop, needs to be balanced and profiled
1/4 scale steering servo
No throttle servo curently. removed for another boat but is simple hobby store parts.
Rubber mounted aluminum engine mounts
Water cooled 23CC Zenoah machined and modified by a shop in Quebec. Turns more than 13K rpms and around 3.5HP Head and rings were replaced about 3 runs ago.
Tuned pipe exhaust

You would need to setup the throttle servo, and ideally for the most speed, you would need to rebalance the prop and do a little prop tunning This is all very easy. You will need a reciever as well, and I just ballon bag the receiver and battery pack. This boat has been raced a little, but was not my primary racing boat. So it is in almost perfect condition. This is a racing boat, and is fun to play around with, but it likes to go fast. Depending on your setup, it can do 70MPH on the straight away, and throws a 10-20ft rooster tail.
Old 08-06-2007, 10:43 PM
  #2  
yeeharacing
Senior Member
 
yeeharacing's Avatar
 
Join Date: Nov 2006
Location: Browns Mills, NJ
Posts: 814
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

#1 ask for a picture
#2 sounds like the boat is going to need some work to get it in the water.
#3 You will need a radio, rx, and servo.
#4 10-20 ft rooster tail.
I'd be really be leary of this deal and research it to death before you make a commitment.

What kind of shape is your chopper in. Is it RTF?

Good Luck
Old 08-06-2007, 10:51 PM
  #3  
Ron Olson
My Feedback: (1)
 
Ron Olson's Avatar
 
Join Date: May 2002
Location: Kalamazoo, MI
Posts: 18,688
Likes: 0
Received 20 Likes on 17 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

That's a lot of engine for an estimated 32" hull! I hope that it's a lot bigger than that.
I'm leery of any trades as I've gotten the shaft before doing a trade. The guy got an almost brand new engine and I got a box full of beat to Hell junk in trade, most of what was not in the pix that he sent me.
Old 08-06-2007, 11:03 PM
  #4  
HeyRobi
Member
Thread Starter
My Feedback: (3)
 
HeyRobi's Avatar
 
Join Date: Sep 2004
Location: Murfreesboro, TN
Posts: 63
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

This is the photos I recieved

The Heli is ARF it needs a RX and TX It was given to me on another trade from a good friend so technically I dont have much money in it but I would say the value of the heli should be atleast 600 although I did not get any bites on it! So the boat sounds fun!! I have a TX and RX I can use it in the boat.


Old 08-07-2007, 12:25 AM
  #5  
TIA
Senior Member
 
TIA's Avatar
 
Join Date: Jan 2003
Location: La Habra, CA
Posts: 1,143
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

You would not get 70mph out of a 3.5 hp 23cc motor with the hydro. I'm getting 68mph with a 26cc 8hp Zen turning almost 19K.

You will probably get around 40-45 at best. It will be a just for funzy boat.

I wouldn't pay more than 500 for it complete.




Artie
Old 08-07-2007, 08:38 PM
  #6  
Paul M
Senior Member
 
Join Date: Mar 2002
Location: Kingsport, TN
Posts: 1,803
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

I hate to beat this horse, but who is building an 8 HP Zen??? I want one[:-]
Old 08-07-2007, 11:48 PM
  #7  
TIA
Senior Member
 
TIA's Avatar
 
Join Date: Jan 2003
Location: La Habra, CA
Posts: 1,143
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!


ORIGINAL: Paul M

I hate to beat this horse, but who is building an 8 HP Zen??? I want one[:-]
Lots of people build them. Here are a couple of the motors I use and vendors I trust.

Mitch or Todd at Quickdraw or Rick at Mastons RC Marine.

Remember these are "Race" motors and they do blow up. I just grenaded one a couple weekends ago. Thats racing!

http://www.quickdrawengines.com/sample_41Y/Page_1x.html

http://www.mastonsrcmarine.com/My_Ho...es/Page17.html

Old 08-08-2007, 10:01 PM
  #8  
TERBObob
Senior Member
My Feedback: (21)
 
TERBObob's Avatar
 
Join Date: Jan 2003
Location: Oelwein, IA
Posts: 3,176
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

Now , I'm not saying that the hull is NOT carbon , but that sure looks like an ABS hull to me . And 32 incher ????? and THAT has a Zen in it ??? I would SURE as heck ask for a few pics of it WITH the motor showing !
Heck .... what tuned pipe is he using ( don't see any sticking out the rear ) and sure as heck do NOT see any Zen there either !
Old 08-09-2007, 06:17 AM
  #9  
crazyotto
Senior Member
My Feedback: (2)
 
crazyotto's Avatar
 
Join Date: Sep 2005
Location: lake havasu city, AZ
Posts: 1,521
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

i see a red spark plug boot and a exhaust tip in last pic.....
Old 08-10-2007, 08:58 AM
  #10  
Earth Surfer
Senior Member
 
Join Date: Jul 2006
Location: Grand Rapids, MI
Posts: 524
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!


ORIGINAL: Paul M

I hate to beat this horse, but who is building an 8 HP Zen??? I want one[:-]

8hp is a big claim for a 26cc piston port Zen engine. I don't believe it--at all. I don't think QD claims that much for the good Mitch motors (of equal size). I would be willing to bet anybody money that no G260, piston port naturally aspriated engine running on gas will ever hit 8hp. The best pipe on a stock engine makes about 4hp (may be a little more)---and your not going to double that power with added porting using the cast Zen cylinder. The best I have ever seen was 7.2hp, but that was a billet cylinder, with much more advanced porting than is possible with the Zen cylinders, and using a pipe that was designed by a student of Dr. Gordon Blair. The engines I am talking about were prototypes, and never made it to production. 6hp is about the max you can get out of a G260 IMO.

Sorry Drag
Old 08-10-2007, 01:19 PM
  #11  
xxxboatworks
Senior Member
 
xxxboatworks's Avatar
 
Join Date: Sep 2004
Location: ft.lauderdale, FL
Posts: 944
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!


ORIGINAL: Paul M

I hate to beat this horse, but who is building an 8 HP Zen??? I want one[:-]
I want one too....it's going to be tough to find a legit 8hp out of a zen.
Old 08-10-2007, 02:48 PM
  #12  
TIA
Senior Member
 
TIA's Avatar
 
Join Date: Jan 2003
Location: La Habra, CA
Posts: 1,143
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

Oops. Meant 7, not 8. [:-]
Old 08-11-2007, 02:33 PM
  #13  
Ed Sidders
Member
My Feedback: (2)
 
Join Date: Jul 2003
Location: Ore City, TX
Posts: 39
Likes: 0
Received 0 Likes on 0 Posts
Default RE: NOT FOR SALE BUT NEED A VALUE!

out of a g-23 ???????????????? Wow !!!!! I want one just to look inside nitrous ???

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.