Just Got an SC8!!!
#76
Member
Join Date: Sep 2007
Location: , ON, CANADA
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
I removed the motor this morning, removed the back plate and the one way bearing? (sorry no camera) had cracked in half. Just like in this photo I found of another person who had the same proble.
http://www.aeforums.co.uk/forum/inde...showtopic=2646
I will call Associated on Monday for a replacement. This sucks.
I will likely get a back plate, and go for a starter box.
http://www.aeforums.co.uk/forum/inde...showtopic=2646
I will call Associated on Monday for a replacement. This sucks.
I will likely get a back plate, and go for a starter box.
#77
Member
Join Date: Dec 2008
Location: Tigard, OR
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
Hi, New here I was looking for SC8 info and came across this, I also Rounded my starter drive and Its at a Horrible angle and combined with a tough break in the shaft just doesn't cut it IMHO, Starter box is next for me, My 1rst tank with the Stock glow plug I just left the igniter on it, Only way mine would stay running which after the first tank it started better but not easy as it was sooo rich with the factory settings, so far after 5 tanks it runs ok but still too rich, went through 4 OS R5 and #8 Glow Plugs, I definately think the R5 is a Better starting plug but i never drove with it FWIW, Lots of Good info on this site, I definately need help on mine! I build 4 cycle Pontiac V8 Race engines and the RC is fairly new to me But overall i'm glad i got the SC8, It Smokes my Bros Traxxas 3.3 Slayer!, Anyone know what all i need for the starter box swap? or should i get a Tiger Drive Made? Thanks Much!
#78
Senior Member
Thread Starter
My Feedback: (11)
Join Date: May 2008
Location: Spring,
TX
Posts: 506
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
You don't need anything for a starter box swap.....other than a working 1:8 scale starter box. I didn't even bother with a back plate for the back of my motor. This is the box that I bought, which is great:
http://images.google.com/imgres?imgu...%3D2%26hl%3Den
What is a Tiger drive? []
http://images.google.com/imgres?imgu...%3D2%26hl%3Den
What is a Tiger drive? []
#79
Member
My Feedback: (5)
Join Date: Oct 2007
Location: bergenfield,
NJ
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
do you know if the AE roto is the same as the losi one, or if they are interchangable? also, has anyone found specs on the engines: stroke, bore, rpm, etc.??
#80
Member
Join Date: Dec 2008
Location: Tigard, OR
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
http://sullivanproducts.com/TigerDriveMainFrame.htm thats the link for the Sullivan Tiger drive setups, Basically they make custom rear plates that put your drive at a different angle so you don't have to go through the rear of the truck to start it, FWIW I still want to use the Box, Thanks for the link! Did you get the different flywheel? Also anyone know who makes the Aluminum 3 finger clutch for these?
#82
RE: Just Got an SC8!!!
Someone on scale4x4rc.org has done an electric conversion on the baby if anyone is into that kind of thing, check it out:
http://www.scale4x4rc.org/forums/showthread.php?t=26820
Tom.
http://www.scale4x4rc.org/forums/showthread.php?t=26820
Tom.
#85
Member
Join Date: Dec 2008
Location: Tigard, OR
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
It wont let me upload pics this time, Its a 6mm Allen thats dead center on the crank no offset at all and is an aluminum plate with steel drive, I'll also weigh my truck with batts and fuel today!
#86
Member
Join Date: Sep 2007
Location: , ON, CANADA
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
AE is coming through and sending a replacement one-way bearing to me.
From my local hobby store. I ordered a back plate for the motor and bought a Onfa truggy starter box.
Once the backplate or AE one way bearing arrives (to fix the prostart system) I'll be ready to run again.
From my local hobby store. I ordered a back plate for the motor and bought a Onfa truggy starter box.
Once the backplate or AE one way bearing arrives (to fix the prostart system) I'll be ready to run again.
#87
Banned
Join Date: Nov 2008
Location: lompoc , CA
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
Hello, Im expecting mine on friday, very excited. Im swaping out the motor for a .28 jammin, or the LRP .28 I havent made up my mind yet. Im also debating getting a aftermarket clutch. Do I have to use the shim that comes with the ae clutch on the aftermarket clutch? Xtm makes a 1/8 slideing clutch. Does anyone have anything good to say about thoes? would it even work, only familiar with the shoe style. Any suggestions on clutch spring rates.
Thanks all
Thanks all
#88
Senior Member
RE: Just Got an SC8!!!
I'd just get some Dynamite Max Life clutch shoes and Mugen 1.0 springs..
Don't know what clutch comes on the SC8, but the stock RC8T alu clutch shoes are good IMO.. I imagine it's the same on the SC8.
Don't know what clutch comes on the SC8, but the stock RC8T alu clutch shoes are good IMO.. I imagine it's the same on the SC8.
#90
Member
Join Date: Dec 2008
Location: Tigard, OR
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
Some type of Carbon or plastic 3 shoe material is what came on my SC8, It definately needs an Upgrade t the Alum shoes, I just Sprang for a AB Drag Mod .28 Picco and 086 pipe, oh BTW mine weighs exactly 10lbs all ready to run a
#91
Member
Join Date: Sep 2007
Location: , ON, CANADA
Posts: 73
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
Thunder Tiger part #AA0779 is the back plate. You'll need to shave the pin off the crank shaft to make it fit.
Got the Ofna Truggy box with dual 775 motors for starting. Stupid AE Pro Start in the most awkward nested position.
Haven't started it up yet. It's been super cold here lately. When it warmer than 0 degrees Celcius I'll give this truck another shot at firing up and motor break in.
Got the Ofna Truggy box with dual 775 motors for starting. Stupid AE Pro Start in the most awkward nested position.
Haven't started it up yet. It's been super cold here lately. When it warmer than 0 degrees Celcius I'll give this truck another shot at firing up and motor break in.
#92
Member
Join Date: Dec 2008
Location: Tigard, OR
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
Ive been having trouble getting mine to start and run and also having a ruff time getting itto lean down enough, seams its still tight even after 6-7 tanks through it, I need to know the Adjustments of a truck that is running good not the break in adjustments but after breaking, Can Anyone help? Thanks, PS The AE Roto Whatever starter is at the Worst angle ever I have no clue who thought that little shaft wouldn't end up rounding off if you actually have to crank on it for a while to start it! I am following suit and getting the same Offna dual motor box, Do you know if i need a different flywheel?
#93
Member
Join Date: Dec 2008
Location: Tigard, OR
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
Another note, The 086 pipe will fit the RC8 Chassis and is not made for our extended RC8T Chassis so either re use your header pipe and rubber splice or get a longer muffler brace and possibly trim the side plastic thats connected to the chassis FWIW
#94
Senior Member
Thread Starter
My Feedback: (11)
Join Date: May 2008
Location: Spring,
TX
Posts: 506
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
I need to know the Adjustments of a truck that is running good not the break in adjustments but after breaking, Can Anyone help?
#95
Senior Member
Thread Starter
My Feedback: (11)
Join Date: May 2008
Location: Spring,
TX
Posts: 506
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
I am following suit and getting the same Offna dual motor box, Do you know if i need a different flywheel?
#96
Junior Member
Join Date: Jan 2008
Location: new bern,
NC
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
I have had my sc8 for a couple of weeks now and finally had a chance to run it at my track. I like the way it looks and handles. what I dont like is the starting system. I have rounded the hex off the starter shaft and will be getting a starter box asap. also is it normal for their to be some leakage of fuel/oil around the roto start area on the motor, after running for awile?
mine runs great and holds its tune nice, (finally). it runs strong and for our smallish track is geared just right. I did change the shock oil and preload shims front and rear to my liking for our track, and she is dialed in nice. I also changed tires to some sportwerks and ofna 17mm rims.
today though I did break my front right steering knuckle and have a replacement on the way, sucks. also most places I have looked online have dropped the price some already.
I was lucky when getting mine at my lhs as I did not need the radio and got 100.00 off the top. sweet.
mine runs great and holds its tune nice, (finally). it runs strong and for our smallish track is geared just right. I did change the shock oil and preload shims front and rear to my liking for our track, and she is dialed in nice. I also changed tires to some sportwerks and ofna 17mm rims.
today though I did break my front right steering knuckle and have a replacement on the way, sucks. also most places I have looked online have dropped the price some already.
I was lucky when getting mine at my lhs as I did not need the radio and got 100.00 off the top. sweet.
#97
Member
Join Date: Dec 2008
Location: Tigard, OR
Posts: 56
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
I just wanted to see how far off i was and needed imput But if its a secret I understand If your truck is leaking oil/fuel then air can be getting in and can screw up the tune From what i understand, Ive rounded 2 starter drives an Just Made my own today out of a harder material and so far so good but the Starter box is still best IMO especially since you don't need to change anything!
#99
Junior Member
My Feedback: (145)
Join Date: Mar 2008
Location: casper, WY
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
its running like a champ too my seeting arent much leamer than stock but sounda like i need to get a new backplate comming so i think i will my rx tx didnt work i could only get about 110 feet away before it took off so i have to send in rx for replacement if i strip mine i'll probly switch engines to a picco outlaw w/pullstart just cause i have one i do like how they just seem to run better and better on every tank of fuel
#100
Senior Member
Join Date: Oct 2007
Location: Amarillo,
TX
Posts: 1,099
Likes: 0
Received 0 Likes
on
0 Posts
RE: Just Got an SC8!!!
ORIGINAL: SC8Derek
Here is My Truck, I ended up with the BD version as you see, Here is the Starter too.
Here is My Truck, I ended up with the BD version as you see, Here is the Starter too.
though, I've already got a standing order for AE's electric conversion kit as soon as my LHS can get hands on it....