rclugnut10

My Feedback: (1)

yeah, i dunno if you can see it but i got some slots cut so i can run my 14t 16 or 17t pinion or should be able to tho with the 14t i may have to mod the center diff mount cuz it gets in the way of the motor but i have no issue hacking a little plastic off there after what i did to the chassie...

the lug

vicdat

Yeah, I see the slots. Use a rounded head bolt on the bottom possibly with a washer and your'e good to go...

BRUSSER

any sugestion on what receiver should i use dont know if mine went dead; is there anyway to find out if same still funtionally, switch went bad wire were coroded but still have the dought on recceiver ; help is deeply appreciated[]

BRUSSER

need get receiver that fit in radio box. help and advice is appreciated[]

mohawkboy

Hey you guys, are the Chaos'es fun little cars to have or would you try to get a bigger truck or car.

vicdat

I like mine for it's novelity value, but it's fairly labor intensive compared to my 10 year old Ofna 1/8 scale buggy...

rclugnut10

My Feedback: (1)

1/10 buggy and truck and a 1/8 MT other than my chaos... that is

i like them all for what they are, bigger is fun tho it can be a pain at times... i like my 1/10;s a lot cuz they are simple to work on fast and just fun all around i can't wait to get my e-Chaos running, cuz its lots of fun to drive but the motor has been annoying for me so it went E.... it all depends on what you wanna do...

the lug

dustint209

this is my chaos with a .16 megatech chris chianelli 1.6hp that i got off of ebay for $50 used. This thing hauls a** ! I also put 12mm adapters and hpi wheels and tires. Of course i had to change that p.o.s tranny, so i used a rc10gt tranny. No more stripping gears. [8D] Video coming soon.

mohawkboy

Hey you guys has any one heard of the Sportwerks Reaction 1/10 scale nitro truck and does any one know if there is a forum for the Sportwerks reaction.

rclugnut10

My Feedback: (1)

http://www.rcuniverse.com/forum/sear...D&sortMethod=d

did a quick search in nitro ST's thats what i got

nice build there i bet that goes fast, what do you need for 12 mm hex's??? they'd be useful...
btw what rims are compatable with the stock hexs and where can i get some???

the lug

daveschutt

I know that the bevel gears in these things always fry but i found that if you dont put diff fluid in the diff just some oil, theres less stress on the gear and they dont strip as easily.[8D]

tomst-maxx

My Feedback: (8)

so I finnaly got to take my chaos back out today. ran two tanks threw of blue thunder 20% and the front diff fried lol. still ran with no problem but after a few jumps the front bumper broke. Down for some more time till the parts come in......

vicdat

We feel for ya Tom...You might want to order the Trinity metal pinions and drive cups soon. Mine are still holding up; I even brought mine to work today to run on our huge new concrete parking lot

tomst-maxx

My Feedback: (8)

the best part is i ordered extra diffs when i got the car but never thought i would break the bumber lol. I dont liker how the bumper is the support for the arm hinge.

rclugnut10

My Feedback: (1)

yeah tho depending on how bad the dammage is i may just run it, they have a metal front hindge brace, right??? cuz i did a similar (maybe same) thing with my evader where the bumper/skidplate front part that covered the hindge pin brace just kept snapping off so i just said screw it, its not with the $ 1.79 for a new one and just run it like it is, no issue so the metal brace taks all the heat, so far so good... just a little tip, or depending on dammage a quick swap of the front and rear ones may be in order because they two diff/shock tower setups are the same parts so you could swap out the bumpers if you want the absorbtion factor up front, because its not probibla that the rear will take lots of heat...

btw with me bumpers take a ton of heat, i really messed up the ones on my savage... 15 ft jump nose dived, leading to a few front flips landing on front bumper outta on of those then rolled onto its wheels, i sheered the two screws that hold the bumpers to the braces, so i got some screws that are 2x as thick and those look like they're a bit bent

the lug

tomst-maxx

My Feedback: (8)

there was no metal hinge on my car the higes screw threw the bumper and thats it. not to big of a deal just got to wait fo more parts to come in..

rclugnut10

My Feedback: (1)

i was just checking like i said i wasn't sure weather they had them on this car... i thought they may but i geuss the don't have um, or maybe its on the inside... cuz on all the other cars i've had its been like that....
yeah waiting for parts does suck...

the lug

tomst-maxx

My Feedback: (8)

yea that part is on the inside of the diff

tomst-maxx

My Feedback: (8)

so i got my parts in yesterday and put them on now i am back running. woohoo!!!!!!!!

vicdat

Good deal Tom. Now your challange is to keep it running...

tomst-maxx

My Feedback: (8)

lol yea always seams to be issue lol

speed King

hey guys i wanted to know if i could put chaos wheels on a xxx-nt if they would even fit or not.

rclugnut10

My Feedback: (1)

i don't think the hex sizes work out, but if you can get the hexes on to the truck then sure, tho, i dunno why you'd want to... the stockers aren't amazing and will be quite a bit smaller, but if you can get the hexs on, or the hex sizes match um no issue as far as mounting them goes...

the lug

vicdat

I don't know why anyone would want anything other than Mini-Inferno Tyres for these little turds...They have a crapload of options, they really cheap (cost not quality) and they bolt right on. Mine have little x-shaped studs and have held-up well on and off the road. One small issue: check the glue when new and add a couple drops of CA carefully if any sections look suspect.

brick64vxl

hey guys ive decided to sell my chaos. i have too many cars right now. check it out heres a link

[link]http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ssPageName=STRK:MESELX:IT&item=300302939611[/link]