Tamiya Pajero-Collective Build
#979
Senior Member
Join Date: Jan 2009
Location: , PHILIPPINES
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
Just finished my Unimog body for my CC-01. Going to run a lexan body for the weight savings (and lower COG) and to preserve the Pajero body. I was going to use a Land Cruiser FJ40 body, but the CC-01 wheelbase is a bit short. I could lengthen the rear links with spacers, but then the Pajero body wouldn't fit anymore. The Unimog fits the standard Pajero wheelbase nicely. Plus I can use it also for my CR-01
#983
Senior Member
Join Date: Jan 2009
Location: , PHILIPPINES
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
ORIGINAL: sheograth
Nice job with the Unimog. The owner of my LHS brought his assembled Pajero into the store... now I'm tempted to buy one.
Nice job with the Unimog. The owner of my LHS brought his assembled Pajero into the store... now I'm tempted to buy one.
Thanks! You should definitely get one. You won't be dissapointed
Anyway I just upgraded to Lipo power, man oh man. The power is insane! Using a Team Orion 30C 3800mah pack with the silvercan, the front right tire lifts off the ground every time you gun it. Might have to change the motor out for something slower
#984
Senior Member
Join Date: May 2008
Location: truro, UNITED KINGDOM
Posts: 616
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
Hi, well i just read through the hole of lunchboxes T-EGG thread then found a link to this one lol. Well here is my pajero with the following specs
Tamiya Pajero rig
Full metal bearing kit fitted
Hitec Zebra 3 channel 40FM radio system
Novak Rooster ESC
Venom Fireball 55T motor
2500Nimh battery
3Racing automatic winch
Topcad racing black aluminium wheels with a 10mm offset
Losi rock claw 1.9" tyres
Hitec 645MG hi-torque servo
Has also had a suspension lift..
Both diffs are locked as well.
I will be using this for mudding,hill climbing and maybe a bit of rock crawling as well.
Please le me know if you think this is a good setup for what i want to use it for and any other comments welcome. ow the body will be painted jet black
Tamiya Pajero rig
Full metal bearing kit fitted
Hitec Zebra 3 channel 40FM radio system
Novak Rooster ESC
Venom Fireball 55T motor
2500Nimh battery
3Racing automatic winch
Topcad racing black aluminium wheels with a 10mm offset
Losi rock claw 1.9" tyres
Hitec 645MG hi-torque servo
Has also had a suspension lift..
Both diffs are locked as well.
I will be using this for mudding,hill climbing and maybe a bit of rock crawling as well.
Please le me know if you think this is a good setup for what i want to use it for and any other comments welcome. ow the body will be painted jet black
#986
Senior Member
Join Date: Jan 2009
Location: , PHILIPPINES
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
ORIGINAL: tamiya trucker
Hi, well i just read through the hole of lunchboxes T-EGG thread then found a link to this one lol. Well here is my pajero with the following specs
Tamiya Pajero rig
Full metal bearing kit fitted
Hitec Zebra 3 channel 40FM radio system
Novak Rooster ESC
Venom Fireball 55T motor
2500Nimh battery
3Racing automatic winch
Topcad racing black aluminium wheels with a 10mm offset
Losi rock claw 1.9'' tyres
Hitec 645MG hi-torque servo
Has also had a suspension lift..
Both diffs are locked as well.
I will be using this for mudding,hill climbing and maybe a bit of rock crawling as well.
Please le me know if you think this is a good setup for what i want to use it for and any other comments welcome. ow the body will be painted jet black
Hi, well i just read through the hole of lunchboxes T-EGG thread then found a link to this one lol. Well here is my pajero with the following specs
Tamiya Pajero rig
Full metal bearing kit fitted
Hitec Zebra 3 channel 40FM radio system
Novak Rooster ESC
Venom Fireball 55T motor
2500Nimh battery
3Racing automatic winch
Topcad racing black aluminium wheels with a 10mm offset
Losi rock claw 1.9'' tyres
Hitec 645MG hi-torque servo
Has also had a suspension lift..
Both diffs are locked as well.
I will be using this for mudding,hill climbing and maybe a bit of rock crawling as well.
Please le me know if you think this is a good setup for what i want to use it for and any other comments welcome. ow the body will be painted jet black
looks good! how does it run with the 55T motor? don't forget to wrap the receiver in a balloon when you go mudding [8D]
#987
Member
Join Date: Nov 2008
Location: lake charles,
LA
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
I havent posted on here in a while. I lost interest in my pajero after my daughter was born. She has taken up most of my time lately but I dusted off the unfinished pajero the other day and decided to finish it. I need to touch up some spots but I thought I would post a pic of her just because.
#989
Senior Member
Join Date: Jun 2008
Location: olathe,
KS
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
#990
RE: Tamiya Pajero-Collective Build
That's great.. I need to get one for my T-Egg!! My self modified ballbearing setup works okay but I don't like the idea of using super glue.. this is better for sure!!
#991
Senior Member
Join Date: Jan 2009
Location: , PHILIPPINES
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
Just got my GPM steering kit today. All the slop is gone, and the wheels now center straight after turning left or right. Definitely a must for every CC01!
#995
RE: Tamiya Pajero-Collective Build
I got a CC-01 but not a pajero -
http://www.tamiyausa.com/product/ite...oduct-id=58445
Not put it together yet, waiting on bearings to come in the mail. Love the realism in the pics of the Pajero's.
http://www.tamiyausa.com/product/ite...oduct-id=58445
Not put it together yet, waiting on bearings to come in the mail. Love the realism in the pics of the Pajero's.
#996
Senior Member
Join Date: Jan 2009
Location: , PHILIPPINES
Posts: 248
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
Just checked ebay, I didn't see any. I got mine directly from GPM for $20 shipped. Write Clara of GPM an email and she will hook you up
her email: chinngai(at)netvigator.com
her email: chinngai(at)netvigator.com
#998
Senior Member
Join Date: Jun 2008
Location: olathe,
KS
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
RE: Tamiya Pajero-Collective Build
i just got 2 for $33 bucks shipped. these with a metal servo horn from hitech makes the steering %100 better. they're supposedly working on a few other cc-01 modded parts that'll be released hopefully soon..