Fuji 50 question
#1
Thread Starter
My Feedback: (12)
Join Date: Mar 2009
Location: Delaware, OH
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
Fuji 50 question
I have two fuji 50's that both had prop strikes that bent the cranks. are the new cranks stronger than the original ones or are they the same. If they are the same I guess I will have to only use them on a tri-cycle gear airframe bird
#3
Thread Starter
My Feedback: (12)
Join Date: Mar 2009
Location: Delaware, OH
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fuji 50 question
You are right that a prop strike "COULD" bend any crankshaft but on most model engines it will not unless it is a hard prop strike. I found that on the Fuji 50 that even just a prop strike that does not break the prop can bend the crankshaft. The engine is a good running engine and I love it otherwise but to spend $100 every time the prop touches the ground is rediculous. Like I said, I am only going to use the Fuji 50 on a tricycle landing gear airframe from now on.
#5
Thread Starter
My Feedback: (12)
Join Date: Mar 2009
Location: Delaware, OH
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fuji 50 question
WhiteRook, You would think this to be the case but my experience has been that both Prop Strikes were with wooden props and the one did not even break the prop. I believe that in an effort to reduce the weight significantly on the Fuji 50 engine the Crank was made of a lesser strength material or the machining left significantly less material thus making it more prone to bending easier. Do not get me wrong, I love the Fuji 50 performance but this little twist is an expensive side effect of a very light engine.
#6
Senior Member
My Feedback: (13)
Join Date: Sep 2004
Location: Fulton,
NY
Posts: 333
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fuji 50 question
Jlem,
You don't mention the particulars about the strikes. How fast was the engine running? Were the propstrikes during taxiing, landing....? My Fuji 50 has nosed over during taxi a couple of times with no ill effects.
You don't mention the particulars about the strikes. How fast was the engine running? Were the propstrikes during taxiing, landing....? My Fuji 50 has nosed over during taxi a couple of times with no ill effects.
#7
Thread Starter
My Feedback: (12)
Join Date: Mar 2009
Location: Delaware, OH
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fuji 50 question
well one was on landing and then nosed over.... it was a christian eagle..... also it has been about five years now since this happened.... I am assuming that the newer ones have a stronger crankshaft in them. Back five years ago there were a lot of threads about how soft the crankshaft was on the Fugi 50...... maybe they heard us and fixed it.... hope so
#8
Senior Member
My Feedback: (13)
Join Date: Sep 2004
Location: Fulton,
NY
Posts: 333
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fuji 50 question
Perhaps they have changed the crank.. I have the same plane, but mine is only about 3 yrs old. It certainly doesn't like to taxi downwind! It seems counter-intuitive, but the plane actually taxies downwind better if I input full down elevator when headed downwind and taxi very slowly. The wind seems to catch underneath any up elevator and push the nose over. Heading upwind, of course, requires the usual up elevator.
#9
Thread Starter
My Feedback: (12)
Join Date: Mar 2009
Location: Delaware, OH
Posts: 19
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fuji 50 question
That is typical of any Bi-plane..... short nose moment.... very tricky sometimes to input just enough down elevator and taxi down wind without a nose over