Align t-rex 600n project
#27
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
well post man brought me some parts today! i did overlook one item though. the set screws for the skid pipes woops!
got the aluminum kde receiver installed. got mostly the landing braces and skid pipes on. missing set screws i forgot to order but that my fault lol. did not put any thread locker on the bolts at this point. waiting till i get the motor installed before i put the thread locker on before i get it permanently mounted. well least helicopter is starting to take shape a little bit lol. now just need to get the engine and some hardware i forgot for the skids. then can move on to the next few steps
got the aluminum kde receiver installed. got mostly the landing braces and skid pipes on. missing set screws i forgot to order but that my fault lol. did not put any thread locker on the bolts at this point. waiting till i get the motor installed before i put the thread locker on before i get it permanently mounted. well least helicopter is starting to take shape a little bit lol. now just need to get the engine and some hardware i forgot for the skids. then can move on to the next few steps
#28
Banned
You are making better progress than I am
well post man brought me some parts today! i did overlook one item though. the set screws for the skid pipes woops!
got the aluminum kde receiver installed. got mostly the landing braces and skid pipes on. missing set screws i forgot to order but that my fault lol. did not put any thread locker on the bolts at this point. waiting till i get the motor installed before i put the thread locker on before i get it permanently mounted. well least helicopter is starting to take shape a little bit lol. now just need to get the engine and some hardware i forgot for the skids. then can move on to the next few steps
got the aluminum kde receiver installed. got mostly the landing braces and skid pipes on. missing set screws i forgot to order but that my fault lol. did not put any thread locker on the bolts at this point. waiting till i get the motor installed before i put the thread locker on before i get it permanently mounted. well least helicopter is starting to take shape a little bit lol. now just need to get the engine and some hardware i forgot for the skids. then can move on to the next few steps
Not many participants in this thread.
I am fathfully following along and rejoice of your progress.
Lots have to take priority over the hobby financial budget.
I know all about that trying to make the ends meet every month.
Best 2 U from Zor
#29
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
thanks. been enjoying assembling this helicopter and been learning alot from it.
its starting to look like a helicopter little bit lol. just need the motor and few other pieces and some servo's and i will be ready to start assembling the tail rotor parts.
been buying the optional parts which cost some money here and there. but i rather have aluminum parts in the place of plastic parts. and keep the plastic to a minimum.
also added few extra aluminum frame stiffeners to keep the frame strong as well.
its starting to look like a helicopter little bit lol. just need the motor and few other pieces and some servo's and i will be ready to start assembling the tail rotor parts.
been buying the optional parts which cost some money here and there. but i rather have aluminum parts in the place of plastic parts. and keep the plastic to a minimum.
also added few extra aluminum frame stiffeners to keep the frame strong as well.
#30
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
UPDATE:
sorry for no updates lately. had some big expense last week my truck transmission went out that cost me $2,700 ouch!!! which means broken truck and i'm out of work till it gets fixed. anyway truck transmission is rebuilt now and all good now. anyway bought few t-rex parts lots that had some of the parts i needed in it like tail boom,tail rotor case,torque tube,metal tail pitch,metal control arm set,horizontal stabilizer free parts lol. now just need 1 kde direct part,some kde tail boom support rods and some gears. got about 3/4 the parts to get me started and the new gears are on there way here. should have those some time this week. i buy parts lots so i pick out what parts i need and sell the rest. kinda disappointed did not get to fly it this summer sigh! nothing says can't fly it on nice winter days though when i get it flying lol.
sorry for no updates lately. had some big expense last week my truck transmission went out that cost me $2,700 ouch!!! which means broken truck and i'm out of work till it gets fixed. anyway truck transmission is rebuilt now and all good now. anyway bought few t-rex parts lots that had some of the parts i needed in it like tail boom,tail rotor case,torque tube,metal tail pitch,metal control arm set,horizontal stabilizer free parts lol. now just need 1 kde direct part,some kde tail boom support rods and some gears. got about 3/4 the parts to get me started and the new gears are on there way here. should have those some time this week. i buy parts lots so i pick out what parts i need and sell the rest. kinda disappointed did not get to fly it this summer sigh! nothing says can't fly it on nice winter days though when i get it flying lol.
#31
Banned
One of your faithful follower
UPDATE:
sorry for no updates lately. had some big expense last week my truck transmission went out that cost me $2,700 ouch!!! which means broken truck and i'm out of work till it gets fixed. anyway truck transmission is rebuilt now and all good now. anyway bought few t-rex parts lots that had some of the parts i needed in it like tail boom,tail rotor case,torque tube,metal tail pitch,metal control arm set,horizontal stabilizer free parts lol. now just need 1 kde direct part,some kde tail boom support rods and some gears. got about 3/4 the parts to get me started and the new gears are on there way here. should have those some time this week. i buy parts lots so i pick out what parts i need and sell the rest. kinda disappointed did not get to fly it this summer sigh! nothing says can't fly it on nice winter days though when i get it flying lol.
Nice to see you are stil progressing.
A hobby is for leisure times when we have some and has to stay within our financial situation.
Myself I just spent $896.00 for replacing a failed computer in my Ford ThunderBird.
It sure cuts off the hobby budget.
I will be here continuing to follow your progress.
Take it easy and enjoy _ _ _
Best regards from Zor.
#32
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
thanks going to start assembling the tail rotor assembly this week as soon as i get my new gears and hardware in the mail. at least get some of it started.
some how i started with one project and now one turned into five lol. but was too good of a deals to pass up. now i have a thunder tiger x50 i paid $150 that has a light roll,then another t-rex 600N that i paid $200 for that had a light wreck. and still have another t-rex 600N and 700 in my dresser drawer that needs assembling still. been pulling parts out of my parts lots for those too.
some how i started with one project and now one turned into five lol. but was too good of a deals to pass up. now i have a thunder tiger x50 i paid $150 that has a light roll,then another t-rex 600N that i paid $200 for that had a light wreck. and still have another t-rex 600N and 700 in my dresser drawer that needs assembling still. been pulling parts out of my parts lots for those too.
#33
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
UPDATE 10/23/14
got the tail boom parts installed. the book calls for one bearing in the tail boom. i had an extra tail boom bearing so i installed 2 tail boom bearings to help with vibration.
got the tail boom and torque tube installed on the helicopter. now just need to work on the tail rotor parts.
also changed my mind and changed out the white main gears to the black main gears was told the black gears were lot better ones.
got the tail boom parts installed. the book calls for one bearing in the tail boom. i had an extra tail boom bearing so i installed 2 tail boom bearings to help with vibration.
got the tail boom and torque tube installed on the helicopter. now just need to work on the tail rotor parts.
also changed my mind and changed out the white main gears to the black main gears was told the black gears were lot better ones.
#34
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
UPDATE 10/24/14
got the main gear installed,main mast installed, swash plate and rotor head on just for fitment. will not be able to hook those up till i get an swashplate leveler and get the radio and servos as those will come little later. also got some kde direct tail upgrades and parts ordered or least what i can afford right now. rest i will have to order later lol.
got the main gear installed,main mast installed, swash plate and rotor head on just for fitment. will not be able to hook those up till i get an swashplate leveler and get the radio and servos as those will come little later. also got some kde direct tail upgrades and parts ordered or least what i can afford right now. rest i will have to order later lol.
#35
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
UPDATE 11/12/14
installed the tail rotor along with the KDE direct tail rotor upgrade. now all i need are the tail boom supports,tail control rod.
next will be the expensive stuff engine,radio system,3 axis gyro. for the motor thinking os 55HZ-H,for radio thinking Futaba 2.4GHz S/FHSS 8JH Radio System,gyro BeastX Microbeast Plus Flybarless Unit.
[TABLE="width: 100%"]
[TR]
[TD="colspan: 2"][/TD]
[/TR]
[/TABLE]
installed the tail rotor along with the KDE direct tail rotor upgrade. now all i need are the tail boom supports,tail control rod.
next will be the expensive stuff engine,radio system,3 axis gyro. for the motor thinking os 55HZ-H,for radio thinking Futaba 2.4GHz S/FHSS 8JH Radio System,gyro BeastX Microbeast Plus Flybarless Unit.
[TABLE="width: 100%"]
[TR]
[TD="colspan: 2"][/TD]
[/TR]
[/TABLE]
#36
Banned
flyingjmerritt,
Not many people in this thread but I am following along.
I can only offer some encouragement with the unique type of activities you are doing.
Best 2 U,
Zor
Not many people in this thread but I am following along.
I can only offer some encouragement with the unique type of activities you are doing.
Best 2 U,
Zor
#37
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
zor
thanks. now all i need is the tail boom supports. pretty soon i will need servos and radio system before i can hook up the swash plate.
getting close to finishing the first helicopter. witch is my personal helicopter with modifications lol. got 2 more have to rebuild too lol
thanks. now all i need is the tail boom supports. pretty soon i will need servos and radio system before i can hook up the swash plate.
getting close to finishing the first helicopter. witch is my personal helicopter with modifications lol. got 2 more have to rebuild too lol
#38
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
been a while since i updated. finally got around to buying some of the expensive stuff. got this radio system used for $250 http://www.amain.com/futaba-10jh-2.4...ceiver/p297659. also managed to pick up an used os 55hz for $75 that needed a new bearing. so replaced both front and back bearings. this engine is normally around $300! now all i need is servos,gyro,governor,battery,charger to make it all go. so i'm making some progress slowly. heck at this rate might even be a chance to have it flying by this spring lol.
#41
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
getting close! since last update bought 4 align ds615 and a align ds655 tail servo,gpro gyro, and just bought a scot gray reactor x2 voltage regulator for the helicopter.
now all i need that's left is tail boom support rods,canopy and blades.
now all i need that's left is tail boom support rods,canopy and blades.
#42
Cool you almost there. Hey I have them servos on my 550 useing them for few months now like them. Just keep eye on there temp I was having temp problems with elevator servo. I think it is because my helie is little tail heavy and servo is working harder than it should be. I added some weight to see if that keep the temp down. Let me know how you like your bird. Have a great night.
#43
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
Cool you almost there. Hey I have them servos on my 550 useing them for few months now like them. Just keep eye on there temp I was having temp problems with elevator servo. I think it is because my helie is little tail heavy and servo is working harder than it should be. I added some weight to see if that keep the temp down. Let me know how you like your bird. Have a great night.
thinking about useing the optional elevator arm before i can hook the back one up. but i'm getting there slowly.
#46
Thread Starter
My Feedback: (3)
Join Date: Jul 2003
Location: waterbury,
NE
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
ya i put them on to help keep orientation during flight. i'v added few aftermarket parts to it here and there.
but for most part most of it is align parts. but this is not i kit helicopter! not bad for building it out of parts lots.
but for most part most of it is align parts. but this is not i kit helicopter! not bad for building it out of parts lots.