Register

If this is your first visit, please click the Sign Up now button to begin the process of creating your account so you can begin posting on our forums! The Sign Up process will only take up about a minute of two of your time.

Page 2 of 2 FirstFirst 12
Results 26 to 42 of 42

  1. #26
    rmh's Avatar
    Join Date
    Dec 2001
    Location
    , UT
    Posts
    12,589
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?


    ORIGINAL: xyzengine

    This is Carl from XYZ,
    I see your issue,I think may be I can help you.pls contact me by zj-jn.cn@hotmail.com
    If you would like send to us ,we will mend it for you with no charge.And if you want us to help contact Hobbycity we will alse be pleased to do so.


    Carl
    I have used ZDZ engines almost exclusively for a number of years.
    Very satisfied with them
    I hav been asked if this new engine from China will withstnd running with tuned exhaust systems .
    We use exclusively 32-1 synthetic oil fuel and have no problems .
    The problem with cracked rotor we know from previous ZDZexperience - typically caused by hardening techinique used in manufacturing
    As we prefer rotary to reed valves setups ,we are watching to see how this engine performs.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	Ca82578.jpg 
Views:	15 
Size:	42.1 KB 
ID:	1195949  
    Libby is still watching you

  2. #27

    Join Date
    Jun 2007
    Location
    Herzliya, ISRAEL
    Posts
    9
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    Now I have the new information - and at all I do not know. That with it to do.
    The letter is received:

    2009-5-11

    Dear Sir,

    Nice day! It’s a pity to tell you that Mr. Wang (qztv1987) quitted his job on 11th May, 2009, from then, his behavior could not represent our company any more, so please do not believe his remittance and transaction request.

    The mail address Zi-jn@hotmail.com and zj-jn.cn@hotmail.com he used before have been taken back by our use, so you can still contact us by these two emails.

    The following contact information is valid permanently:

    Fax: +86-570-2932510

    Mobile Phone: +86-13305701084

    ANNE Email: Zi-jn@hotmail.com

    CARL Email: zj-jn.cn@hotmail.com

    Qingfu Zheng Email: zqf1084@msn.com

    http://www.zj-jn.cn

    http://www.zj-jn.net.cn

    If there’s any remittance transaction, detail account No. and total amount will confirmed from Email: zqf1084@msn.com

    Best regards & Thanks.

    Zhejiang Quzhou Jinnuo machinery Co. Ltd.

    Qingfu Zheng (General Manager)



    2009-5-11


    There is mister Carl with nick xyzengine the deceiver?

  3. #28
    nowinkk's Avatar
    Join Date
    Jan 2007
    Location
    Kota KinabaluSabah, MALAYSIA
    Posts
    129
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    In this case, you'd better contact Mr. Qingfu Zheng, the General Manager himself.

    It is rather weird that CARL Email: zj-jn.cn@hotmail.com is still valid, as shown in the list of permanent contact information.
    Life ends when u stop dreaming; Hope lost when u stop believing n Love fails when u stop caring. So dream, believe n care...

  4. #29
    airwethead's Avatar
    Join Date
    Jan 2002
    Location
    Centerville, UT
    Posts
    251
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    What a bummer. I would have liked to have seen if this matter was taken care of. Strange that Mr. "Carl" from China disappeared, and we have heard nothing in two months. I was about to buy an XYZ engine from HobbyCity, but have seen just about enough here to scare me off[&:]

  5. #30

    Join Date
    Jun 2007
    Location
    Herzliya, ISRAEL
    Posts
    9
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?


    ORIGINAL: airwethead
    ... I was about to buy an XYZ engine from HobbyCity, but have seen just about enough here to scare me off[&:]
    You are right.

  6. #31
    66-stang's Avatar
    Join Date
    Dec 2004
    Location
    Collinsville, IL
    Posts
    52
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    Maybe all can now see why SERCE dropped their line ???
    Fly it like you hate it....

  7. #32

    Join Date
    Dec 2006
    Location
    Poplar Bluff, MO
    Posts
    108
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    I have a Turnigy 50 CC, HP. It is the rotary valve engine. With a Vox 20 X 10 prop, and a MT tuned pipe is is turning 8200RPM. Very powerful engine. Engine ran rough at first, but found ign timing to be out of adjustment. The factory setting, at least on my motor was set at 36deg advanced. Reset to 28deg advanced, and world of diference. It actualy picked up some RPM. Idel is very smoth now, and good transation. It will pull my big 102 inch wing span AirTractor straight up. Plane weighs 20 pounds. It has more power than my DA 50. So far I am well pleased with this motor. Time will tell.
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	Pn36072.jpg 
Views:	11 
Size:	64.0 KB 
ID:	1362529  

  8. #33

    Join Date
    Nov 2004
    Location
    Tehachapi, CA
    Posts
    264
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    I purchased on of them a while back and had some issues with it starting and running, after replacing the Carburator with a Carb from a Evolution 26 wich i had laying around it got way better but the ignition crapped out after 10-12 min on my test stand. Replaced it this Weekend with a DLE ignition putting another plug on the trigger connector and setting the timing to 28 degree it starts like a DA and it rips a 21X10 NX with 6200 Rpm with excellent transition. Still little tricky starting warm but i'm use to that from my ZDZ 40 who is a rotary valve motor just as well with the same behavior
    I put this Engine in a Reactor 160 and reply here results after flying it, but so far it runs good, perfect is something else we most likely
    never archive with affordable Engines from unknown manufacturers.
    I keep my eye on this post
    Michael
    Carl Goldberg Ultimate Brotherhood member 26

  9. #34
    SERCE's Avatar
    Join Date
    Nov 2005
    Location
    Jacksonville, FL
    Posts
    137
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    Raubold,
    I very rarely get on the forums, but I subscribed to this one because of our past experience.

    Running 6200rpm on a 21x10 prop is not a strong engine in today's standards.
    You should be close to 6900-7000 with that prop.

    The #1 problem with that engine is the design on it's valve clearances and the poor bearings they have used.

    The #2 problem is their ignition will not hold up.
    We replaced around 60 of their ignitions over a 1-1/4 year period. Most they would not give us in warranty.

    The #3 problem is, when they get hot they are hard (if not successful) to start.

    My suggestion (if you decide to keep it) is to replace the ignition with a Rcexl, re-time it and run it till it dies.

    I could get into other issues, but being a major supporter to FG and the fact that I am (or try to be) a
    business professional, it would be wrong.
    Ron
    Southeast R/C Engines
    www.southeastrcengines.com
    \"The low cost leader in quality gas engines\"

  10. #35

    Join Date
    Nov 2004
    Location
    Tehachapi, CA
    Posts
    264
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    I live and fly in real 5800 feet altitude and for that its pretty good, i think
    Carl Goldberg Ultimate Brotherhood member 26

  11. #36

    Join Date
    Nov 2004
    Location
    Tehachapi, CA
    Posts
    264
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    forgott, Ignition now DLA (the XYZ one sucks)yepp works, mentioned in my forum reply Carb from Evolution 26, smaller ventury but all over impovement, front bearing from 3W 150, same and no loosnes anymore, all over runs sweet, stars like a ZDZ 40 no difference just have to figure out its habbits. Cant beat the price and all of them Gassers have an Up and Down somewhwre.
    Flipp, run and fly all what counts
    Michael
    Carl Goldberg Ultimate Brotherhood member 26

  12. #37

    Join Date
    May 2007
    Location
    Hope, BC, CANADA
    Posts
    13
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    Hi, I purchased the Turnigy last year and was upset because it came when I broke my wrist! I got antzy and set the engine on the test stand.
    It ran wonderfully with around 25 lbs thrust. Few months later I test flew the Extreme Flight 74" Yak.
    Had 3 flights on it and everything was fine, I did some repairs to the airframe and put it away for the winter.
    Today I got it out in full dress on the driveway. The darn engine would not run except on prime! I tested the fuel lines andall was well,
    on close inspection the pressure tube was kinked. Replaced and still no go! I pulled the engine and will try it on the test stand.
    I'm at a total loss to know what happened!?!
    Any suggestions are welcome....
    Jim
    RCM Plan and Article Series:
    pulling-gz.blogspot.com

  13. #38

    Join Date
    May 2007
    Location
    Hope, BC, CANADA
    Posts
    13
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    Hi All, After setting the engine on the test stand, I started thinking back to Sept when I last flew. The pushrod I had on the choke came apart and thus finished my flying for the day... so I thought. The first flight was uneventful except for the landing where I duffed the prop and bent the landing gear in the soft sod. Now back on the stand I though what if the woodruff key was sheered and by flight 3 shifted causing the timing to be out.
    Well I couldn't budge the nut on the hub but I took a reading of the timing and found the Hall Sensor to be at 51*TDC. I tried to move the sensor and it was loose.
    Set the timing to 27*TDC and after 15 minutes of flipping it started and ran. When it has ran for a while' it sure is hard to start again!
    I ran it with a JXF 20x10 prop hoping for less thrust but got 24 lbs and 6810 RPM.
    Jim
    RCM Plan and Article Series:
    pulling-gz.blogspot.com

  14. #39

    Join Date
    May 2009
    Location
    calgary, AB, CANADA
    Posts
    2
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    The TGY52 Overbore , do u know what kinda battery i should be using for this ?
    some people said only to use a 4.8v 1500mah , is that right ?

    thanks for any help

  15. #40

    Join Date
    May 2007
    Location
    Hope, BC, CANADA
    Posts
    13
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    Hi, It depends how much flying you plan to do. I have a 4.8 1400Mah pack with my Turnigy HP50, I have never ran a battery out with an ignition system yet.
    The next plane I get will have a Lipo with the output at 6 volt.
    Hope this helps.
    Jim
    RCM Plan and Article Series:
    pulling-gz.blogspot.com

  16. #41

    Join Date
    May 2009
    Location
    calgary, AB, CANADA
    Posts
    2
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    i was thinking off runing a 4.8v 1500mah spektrum since i have one that i am not using

  17. #42

    Join Date
    May 2007
    Location
    Hope, BC, CANADA
    Posts
    13
    Gallery
    My Gallery
    Models
    My Models
    Ratings
    My Feedback

    RE: hobby city Turnigy HP 50 engine-any good?

    Hi, if it isn't too old and keeps a steady charge, you will do fine. Cycle it to find out the discharge time, you don't want a weak battery on your plane.
    I had a 1000Mah NiCad that was still good but used it for bench running only.
    Jim
    RCM Plan and Article Series:
    pulling-gz.blogspot.com


Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
All times are GMT -6. The time now is 05:24 AM.

SEO by vBSEO 3.6.1 ©2011, Crawlability, Inc.