RCU Forums

RCU Forums (http://www.rcuniverse.com/forum/)
-   Gas Engines (http://www.rcuniverse.com/forum/gas-engines-142/)
-   -   New SV Gassers (http://www.rcuniverse.com/forum/gas-engines-142/6486808-new-sv-gassers.html)

Starfighter 05-23-2008 04:56 PM

RE: New SV Gassers
 
Has any tried RC Showcase for the status of parts for the SV 26 as their website shows it's available from them.

freeonthree 05-23-2008 05:48 PM

RE: New SV Gassers
 
Yeah, I just did, thanks ! I see theirs has a choke ! $225.00 is fine, if their in the USA and shipping is reasonable, for me anyway. My friend needs two for a Cessna. I see they also state the ign voltage as 4.8 to 6.7, so my 2000ma 6 volt NiHM batt is just fine. If shipping is $8.00 to $12.00 now, we'll be very happy. Thanks for the website ! Dennis

ozzmanace 05-27-2008 06:35 PM

RE: New SV Gassers
 
ok i ran my 2nd engine today. runs awesome. dialed the high and low needle valves and i'm very happy. but my first engine is not so good. i have run maybe a 1/2 a gallon thru it. i've changed carbs, mufflers, gas mix., everything mentioned in this web site. the problem from the start and still is when i try to give it full gas it dies. everytime. any suggetstions? i've looked on the web for a new stock carb, or even a rebuild kit. could not find any.

ca$hey 05-27-2008 08:59 PM

RE: New SV Gassers
 
New Vid ,,,still goin Strong
http://www.youtube.com/watch?v=XEgsp...r=asc&start=30

freeonthree 05-27-2008 09:52 PM

RE: New SV Gassers
 
Open the high speed needle 1/4 turn and let me know how it runs

freeonthree 05-27-2008 10:42 PM

RE: New SV Gassers
 
Lookin good Jonney ! Is that an SV26 ?

ca$hey 05-27-2008 11:09 PM

RE: New SV Gassers
 
Yep same one;)

freeonthree 05-27-2008 11:26 PM

RE: New SV Gassers
 
Sounds like it's runnin good. :D

ca$hey 05-28-2008 12:25 AM

RE: New SV Gassers
 

Quote:

ORIGINAL: freeonthree

Sounds like it's runnin good. :D
Its a littel rich that day,,,,it changes very easy depending on the altertued,,but it still run good thow

ozzmanace 05-28-2008 05:09 PM

RE: New SV Gassers
 
its the same way no matter if it's lean or rich. i've tried it all.

freeonthree 05-28-2008 06:26 PM

RE: New SV Gassers
 
What do you mean the same ? What does it do ? It sounded good to me. Whay prop are you running on it ?

bako 05-29-2008 09:24 AM

RE: New SV Gassers
 
today I have tryed topflight 20X6-10, only 5.6kg of thrust, with cherry 17X8 I have 5.2kg. I wanna try cherry 18X6 for it, ot some zinger 18X6 or something like this. anubody has figures with theese props? I see this chinesee props aren't enough awfull for throwing away :)

ca$hey 05-29-2008 01:15 PM

RE: New SV Gassers
 
Im useing the Hawker 18x6 wood ,,,on a good day about 7800rpm,,,,I did see a spe 26 running a apc 16x12 it had plenty pull to

freeonthree 05-29-2008 01:29 PM

RE: New SV Gassers
 
Here's an 18x8 Master Airscrew Classic on an SV26 and a 16 pound Stearman. Works well...
http://www.youtube.com/watch?v=vyvd2qmcobw
It appears that you tube is having a problem. The video is still there, but off and on now...

GUAIO 05-30-2008 09:16 AM

RE: New SV Gassers
 
what spark plug are you guys using for replacement??? I think mine is going bad

ozzmanace 06-09-2008 04:53 PM

RE: New SV Gassers
 
ngk bpmr6f spark plug. hey freeonthree, what gasket material did you use, and where did you get it? it's the only thing i can come up with thats bad on the carb side of things. by the way it's a hard to find spark plug. but if you read thru the past entries you'll find where to buy. i don't remember off hand it's been some time. however iv'e found that the plug cap doesn't fit very well. may need to make some adjustments.

freeonthree 06-09-2008 05:05 PM

RE: New SV Gassers
 
You can buy an NGK BPMR6F spark plug, and gasket material for your engine, at Napa Auto Parts.
The metal sleeve on the plug cap fits very tight, and thats a good thing. I also wire tie around the plug cap and to the bolt entry hole in the top cooling fin of the cylinder just in case.
Make sure your head has a tapered seat if you use the BPMR6F. The SV26 has the tapered seat. Some engines use a spark plug with a gasket though... Dennis

JerKap 06-09-2008 06:06 PM

RE: New SV Gassers
 
Is the RCS SV50 a different engine than the SV 50 that has been talked about in this thread?

http://www.rcshowcase.com/html/RCS/rcssv50.html

freeonthree 06-09-2008 06:23 PM

RE: New SV Gassers
 
I don't know, but if it is, I sure hope they fixed the balance of the crankshaft, and also the problem of the rod sliding off the pin. I can't believe they even let those engines go out the door. I call that a huge lack of engineering and quality control. Dennis

61ahs 06-14-2008 08:40 AM

RE: New SV Gassers
 
HobbyCity has the SV26 single and the SV50 and SV100cc twins listed on their website again. And they even have some in stock.

The SV50 single isn't listed, so I would guess the manufacturer still doesn't have the bugs worked out.

Rick

Mitsu1 06-15-2008 09:10 AM

RE: New SV Gassers
 
The RCS SV50 is a different engine than what was formerly listed as SV50. This new engine is a rip from the DL50 as it's wearing the cylinder jug from the DL50, but has its own CNC machined crankcase.

new225 06-16-2008 03:23 AM

RE: New SV Gassers
 
Hi guys! More Thanks for all information.
The engine (SV-26) has been modified according to your advice. rpm range: 1500-8600 with prop Master Airscrew 16*8, thrust - 5.4-5.6kg (12-12.3 Pounds)
I placed the sv-26 aboard the Katana (0.40 glow size - wingspan 1400mm - 55") It flies http://www.youtube.com/watch?v=cHU9kiktQLY

freeonthree 06-16-2008 03:56 AM

RE: New SV Gassers
 
Good job !

ozzmanace 06-16-2008 04:43 PM

RE: New SV Gassers
 
well i had my first flight with this engine yesterday. on a 90 size ultimate bi plane. it did awesome. it really sounded good. but on the down side, a friend flew his for the first time and the magnet fell out for his ignition.

freeonthree 06-16-2008 04:57 PM

RE: New SV Gassers
 
It fell out, or flew out ? I assume it's gone... Do you need help locating a new hub ? Dennis


All times are GMT -8. The time now is 08:21 AM.