Hirobo Support Forum Greg Gomes of MRC/Hirobo is your host. Ask all your Hirobo questions here!

Shuttle Plus

Reply

Old 05-29-2007, 04:52 PM
  #1  
me-109e
Junior Member
Thread Starter
 
Join Date: Feb 2007
Location: Grimstad, NORWAY
Posts: 3
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default Shuttle Plus

Hi,
I'm pretty new in heli flying and I got some trouble getting it rigth. I have a shuttle +, a Futaba 7c and a futaba gyro 401. Can someone give me some advice on the gyro parameters? I can juse from N 100% to A 100% in all three idle (N, 1 and 2) in the manual it says:
norm NOR 100%
IDL1 NOR 70%
IDL2 NOR 70%
HOLD NOR 80%
What is the difrense between A and N? etc....
Need good advices

-Dont cray, it always comes back down!-
me-109e is offline  
Reply With Quote
Old 05-29-2007, 06:29 PM
  #2  
du1br@yahoo.com
Junior Member
 
Join Date: Mar 2007
Location: Malabon CityMetroManila, PHILIPPINES
Posts: 3
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default RE: Shuttle Plus

enjoy your company.
du1br@yahoo.com is offline  
Reply With Quote
Old 05-29-2007, 07:08 PM
  #3  
du1br@yahoo.com
Junior Member
 
Join Date: Mar 2007
Location: Malabon CityMetroManila, PHILIPPINES
Posts: 3
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default RE: Shuttle Plus

I am looking for a shuttle plus that was not completed because the owner became busy and willing to sell it.
du1br@yahoo.com is offline  
Reply With Quote
Old 05-29-2007, 07:10 PM
  #4  
du1br@yahoo.com
Junior Member
 
Join Date: Mar 2007
Location: Malabon CityMetroManila, PHILIPPINES
Posts: 3
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default RE: Shuttle Plus

Is there a shuttle plus available from our friend who was not able to complete the kit who became busy and is selling it?
du1br@yahoo.com is offline  
Reply With Quote
Old 05-30-2007, 07:51 AM
  #5  
CollectivelySpaced
My Feedback: (18)
 
CollectivelySpaced's Avatar
 
Join Date: Sep 2005
Location: Oak Ridge, NC
Posts: 281
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default RE: Shuttle Plus


ORIGINAL: me-109e

Hi,
I'm pretty new in heli flying and I got some trouble getting it rigth. I have a shuttle +, a Futaba 7c and a futaba gyro 401. Can someone give me some advice on the gyro parameters? I can juse from N 100% to A 100% in all three idle (N, 1 and 2) in the manual it says:
norm NOR 100%
IDL1 NOR 70%
IDL2 NOR 70%
HOLD NOR 80%
What is the difrense between A and N? etc....
Need good advices
On the GY-401 "N" is normal or rate mode and "A" is AVCS or heading hold.
CollectivelySpaced is offline  
Reply With Quote
Old 06-04-2007, 02:12 PM
  #6  
me-109e
Junior Member
Thread Starter
 
Join Date: Feb 2007
Location: Grimstad, NORWAY
Posts: 3
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default RE: Shuttle Plus

Hi,
Me again. Do any one have a better PI-curv and TH-curv? I have an O.S. 37 and the curvs in the manual says:
TH-CURV: POS1 POS2 POS3 POS4 POS5
Norm 0.0% 30.0% 44.5% 65.0% 100.0%
IDL1 70.0% 60.0% 60.5% 75.0% 100.0%
IDL2 80.0% 70.0% 70.5% 80.0% 100.0%
PI-CURV: POS1 POS2 POS3 POS4 POS5
Norm 20.0% 42.5% 65.0% 77.5% 90.0%
IDL1 15.0% 33.5% 52.0% 68.5% 85.0%
IDL2 15.0% 26.0% 37.0% 58.5% 85.0%
but it I dont get the wanted RPM. My ZX with a 32 size and the manual curves have the rigth RPM? any suggestion?
me-109e is offline  
Reply With Quote
Old 06-04-2007, 02:21 PM
  #7  
mrc-hirobo
Senior Member
 
Join Date: Dec 2004
Location: Edison, NJ
Posts: 106
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default RE: Shuttle Plus

Is the RPM too high or too low?

Basically the same curves from your ZX should work on the Plus. Same dimensions etc. Just the 37 will put out more power and possibly a higher RPM.

What is the pitch curve degree amounts that correspond with the percentages you listed.

Thanks!
Jeff
mrc-hirobo is offline  
Reply With Quote
Old 06-04-2007, 03:04 PM
  #8  
me-109e
Junior Member
Thread Starter
 
Join Date: Feb 2007
Location: Grimstad, NORWAY
Posts: 3
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default RE: Shuttle Plus

Hi,
The RPM is too low and the pitch curve degree is:
Hovering Loop Roll Auto-rotation
High pitch 8~9 8~9 7~8 10
Hovering 5~6 3 0 -
Low pitch -3 -5 -5 -5

Audun
me-109e is offline  
Reply With Quote

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service