Jet Central Turbines - Artes Jet Jet Central Turbines formerly the Artes Jet forum

Jeti Radio setup with Cheetah SE-failsafe/manual cooling

Reply

Old 08-20-2017, 03:37 AM
  #1  
VK96
Thread Starter
 
Join Date: Oct 2016
Location: Hooksett, NH
Posts: 115
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default Jeti Radio setup with Cheetah SE-failsafe/manual cooling

Hoping someone can share their setup as I'm having a few issues with my ECU not responding correctly. It appears to be calibrated correctly as it idles fine around ~35k with a max of ~130k (also getting "min" and "max" pump ok msgs). The issues I'm running into are related to the "Failsafe", as well as "Manual Cooling".
I have my throttle end points set at +100 to -100 (including limits) and taught the ECU as the manual says. Everything looks good on the HDT as it sees max throttle and idle in the "green" band. I set my failsafe in the CB200 to -125 and when disabling transmission the ECU says "Failsafe". However, the engine only goes to idle and remains there. If I change the failsafe in the CB200 to "Out off" it will then shutdown the turbine and say "No Rx". Unless "Failsafe" in the ECU is meant to only bring the engine to idle I believe something is not correct.
Also, when I raise the throttle with trim down it will not begin the manual cooling process. If anyone has any insight I'd be greatly appreciated!
VK96 is offline  
Reply With Quote
Old 08-24-2017, 10:15 AM
  #2  
rskiba
My Feedback: (16)
 
rskiba's Avatar
 
Join Date: Jan 2004
Location: Pasco WA
Posts: 51
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

I am interested in the clarification of failsafe and "off" as well since I am going to be running a CB200 as well.
rskiba is offline  
Reply With Quote
Old 08-24-2017, 11:19 AM
  #3  
rcjets12
My Feedback: (21)
 
rcjets12's Avatar
 
Join Date: Apr 2002
Location: Palm Bay , FL
Posts: 380
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

We are investigating the failsafe issue and will get back to everyone.
rcjets12 is offline  
Reply With Quote
Old 10-24-2017, 11:53 AM
  #4  
rskiba
My Feedback: (16)
 
rskiba's Avatar
 
Join Date: Jan 2004
Location: Pasco WA
Posts: 51
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

Any updates to this issue?

Thanks,
rskiba is offline  
Reply With Quote
Old 10-24-2017, 06:25 PM
  #5  
VK96
Thread Starter
 
Join Date: Oct 2016
Location: Hooksett, NH
Posts: 115
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

Spoke with Jose while he was in MEX last week. Sent him a video and am waiting to hear back. Will post when I do!
VK96 is offline  
Reply With Quote
Old 10-27-2017, 09:29 AM
  #6  
rskiba
My Feedback: (16)
 
rskiba's Avatar
 
Join Date: Jan 2004
Location: Pasco WA
Posts: 51
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

Anxious to hear what's up. Thanks!
rskiba is offline  
Reply With Quote
Old 02-27-2018, 11:38 AM
  #7  
rskiba
My Feedback: (16)
 
rskiba's Avatar
 
Join Date: Jan 2004
Location: Pasco WA
Posts: 51
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

Any updates on this issue or is now resolved and not a problem?
rskiba is offline  
Reply With Quote
Old 02-27-2018, 04:49 PM
  #8  
VK96
Thread Starter
 
Join Date: Oct 2016
Location: Hooksett, NH
Posts: 115
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

Operator error...I inadvertently set the throttle channel to "linear" instead of the default "throw low". Once I swapped it back and re-calibrated everything is working as it should.
VK96 is offline  
Reply With Quote
Old 02-28-2018, 01:54 PM
  #9  
rskiba
My Feedback: (16)
 
rskiba's Avatar
 
Join Date: Jan 2004
Location: Pasco WA
Posts: 51
Gallery
My Gallery
Models
My Models
Ratings
My Feedback
Default

Thx VK96!
rskiba is offline  
Reply With Quote

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service