Carl Goldberg Ultimate 10-300 Brotherhood.
#1103
My Feedback: (2)
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Very cool, *thumbs up*
ORIGINAL: jglemba
Bill started to make some templates to make a few backup planes after working on the restoration. He's been cutting out parts for the fuselage sides and tops along with some formers. He has been busy! He also made a nifty little dremel tool type router table to help make the lite ply sides!
ORIGINAL: jglemba
I would like to join the Ultimate Brotherhood. Restoring a 15 year old 1300
Thanks, Joe[font=''Verdana''][/font]
[img][/img]
I would like to join the Ultimate Brotherhood. Restoring a 15 year old 1300
Thanks, Joe[font=''Verdana''][/font]
[img][/img]
#1104
Member
Join Date: Aug 2009
Location: Victor HarborSouth Oz, AUSTRALIA
Posts: 67
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Ultimate kit for sale on RCTrader if anyone is interested (not mine).
www.rctrader.com/category/341/GasPetrol/listings/6175/Carl-Goldberg-Ultimate-10-300-Kit.html
www.rctrader.com/category/341/GasPetrol/listings/6175/Carl-Goldberg-Ultimate-10-300-Kit.html
#1105
Member
Join Date: Jan 2012
Location: Athens, GREECE
Posts: 84
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Having selected to re-engine the Ultimate, it became necessary to modify the cowl.
The previous engine (YS) was side mounted and the new DLE will be mounted inverted.
The hole in the side of the cowl needed to be covered and a new hole opened in the bottom for the new installation.
First step was to use a Dremel tool to “clean” around the existing hole removing all paint etc. and thinning the material to avoid a ridge where the old glass will mate with the new glass.
The glass cloth and epoxy resin need a mold to cure against, the large opening where the cowl has a slight curve was covered with a section of a soft plastic bottle and the flatter sections were simply covered with clear packaging tape.
Three layers of diagonal weave glass cloth were laid down and saturated with laminating epoxy resin. When this cured the “mold” was removed to revel the blocked off hole where a bit of TLC filling and sanding is needed.
I will soon be in position to start priming and preparing for final finish.
mike
#1106
My Feedback: (4)
Join Date: Jan 2002
Location: Westhampton Beach,
NY
Posts: 860
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Mike, great timing as I am doing the same with a CG Ulti I picked up used. Converting it form a Como .90 to a DLE 20.
I may try what you did to save a few bucks but this one has the stock plastic cowl, so I may end up spending the $$ and get a nice 'glass one instead as there is a large portion missing on the bottom from the Como's muffler as well.
Bill S.
I may try what you did to save a few bucks but this one has the stock plastic cowl, so I may end up spending the $$ and get a nice 'glass one instead as there is a large portion missing on the bottom from the Como's muffler as well.
Bill S.
#1107
Member
Join Date: Oct 2011
Location: sherbrooke,
QC, CANADA
Posts: 81
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Hello brothers!!!!
i got my plans printed out for my own bipe!!! Now i will need to find a landing gear! and sort out all the wood and ply required to build my bipe.i found the cowling and canopy at Fiberglass specialties.
The easiest to find will be ultracote!
Kinda nervous about this project cause it will be my first scratch built.
Anybody has some blue hawk stickers for sale?
i got my plans printed out for my own bipe!!! Now i will need to find a landing gear! and sort out all the wood and ply required to build my bipe.i found the cowling and canopy at Fiberglass specialties.
The easiest to find will be ultracote!
Kinda nervous about this project cause it will be my first scratch built.
Anybody has some blue hawk stickers for sale?
#1108
Member
My Feedback: (1)
Join Date: Feb 2008
Location: Princeton, MN
Posts: 35
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
A lot of the parts for the older Goldberg stuff is still available through Hobby Services. I've been ordering from them over the last year. Do note that the prices have gone up from what is on the site. The "Blue Hawk" decals are part number 2283.
Goldberg Parts
Limited quantities - call or e-mail for availability
Great Planes Product Support (217) 398-8970, option 3
[email protected]
Goldberg Parts
Limited quantities - call or e-mail for availability
Great Planes Product Support (217) 398-8970, option 3
[email protected]
#1109
Senior Member
Join Date: Oct 2011
Location: ontario,
CA
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
well guys is great to see so much about this ship here this ship was my first biplane while learning to fly and now i got a 100cc ultimate great ships no matter what size
#1110
My Feedback: (5)
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
ktmfrank, let me know if you're going with the wire landing gear, if so i can bend you up a set when my shoulder heals or
http://www.fibertechnmore.com/index....on=show_detail
http://www.fibertechnmore.com/index....on=show_detail
#1111
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
ORIGINAL: ktmfrank
Hello brothers!!!!
i got my plans printed out for my own bipe!!! Now i will need to find a landing gear! and sort out all the wood and ply required to build my bipe.i found the cowling and canopy at Fiberglass specialties.
The easiest to find will be ultracote!
Kinda nervous about this project cause it will be my first scratch built.
Anybody has some blue hawk stickers for sale?
Hello brothers!!!!
i got my plans printed out for my own bipe!!! Now i will need to find a landing gear! and sort out all the wood and ply required to build my bipe.i found the cowling and canopy at Fiberglass specialties.
The easiest to find will be ultracote!
Kinda nervous about this project cause it will be my first scratch built.
Anybody has some blue hawk stickers for sale?
If you want a carbon landing gear you could use on of the ones sold by http://www.graphtechrcshop.com/. Fits well too. Ican dig out the details of the one Iordered and mounted on my own bluehawk.
- Thomas
#1114
Junior Member
Join Date: Apr 2012
Location: Spring,
TX
Posts: 18
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Matt - That's really funny. My procrastination on my GP RV-4 is what's holding up my Ultimate build too. I'm actually building two at the same time. One's by the plan and the other is a scratch with lots of modifications like a turtledeck, surface trim tabs and small winglets.
#1115
My Feedback: (2)
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
The great planes .40 size version. I started it thursday and only working 1-2 hours a day have 2 wings the tail and halfway through the body done... so to say it builds fast is an understatement... That being said I don't really love the kit/instructions. Experienced builders would be fine, but there are a number of trip-ups that have left me dissappointed with the kit that could so easily be fixed. For example the top of the fuselage should really be made out of 1 piece aircraft ply... instead its 4 peices that get butt jointed together... I don't have a lot of faith in butt jointed plywood joints.... the other gripe is they updated the parts lists but not the booklet so you spend a lot of time looking for pieces that don't exist b/c they have been swapped out.
I guess the speed of the build makes up for it. and from what I have heard its a wonderful flying plane.
btw, haven't forgotten, I'll get on those templates here and get them sent out to you to add to the .zip file.
I guess the speed of the build makes up for it. and from what I have heard its a wonderful flying plane.
btw, haven't forgotten, I'll get on those templates here and get them sent out to you to add to the .zip file.
ORIGINAL: peternj
Matt,
NICE!!!!
the RV4, is it the great planes one? i got one in my build list
Matt,
NICE!!!!
the RV4, is it the great planes one? i got one in my build list
#1116
My Feedback: (2)
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
i actually was contemplating a turtle deck.. I've always loved the look of the cap-21 and doing that would make this plane look very similar.... i want to just get it done though so its likely coming out with a stock look so I can get flying this spring and get to building the ultimate, which honestly is really what I want to be working on.
Sorry for getting this thread off topic :-)
Sorry for getting this thread off topic :-)
ORIGINAL: dmarusa
Matt - That's really funny. My procrastination on my GP RV-4 is what's holding up my Ultimate build too. I'm actually building two at the same time. One's by the plan and the other is a scratch with lots of modifications like a turtledeck, surface trim tabs and small winglets.
Matt - That's really funny. My procrastination on my GP RV-4 is what's holding up my Ultimate build too. I'm actually building two at the same time. One's by the plan and the other is a scratch with lots of modifications like a turtledeck, surface trim tabs and small winglets.
#1117
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Getting the CG restoration project closer to completion. Bill finished the fuse. We put it together to test fit the wings, landing gear, mount the CFG 20cc motor, etc. We checked the cg and it looks like with two servos in the rear for the elevator and an 8 oz. tank, it worked out perfect. He also has his fuse built for his. Now he is getting started on the wings. He's moving right along!
#1122
Member
Join Date: Jan 2012
Location: Athens, GREECE
Posts: 84
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
I too am preparing my Ultimate with a DLE 20 and a 8oz DuBro tank.
My YAK 54 with an Evolution 26cc GX engine and a 9oz tank gives me a 10min with 1-2min reserve and that engine is 30% larger.
Logically 8 oz should be enough for a small 20cc gas engine.
My Zenoah 20cc engine manual states 1000ml fuel for 1 hour running at WOT. That is around 1/2oz a min. Is it possible that the DLE 20 consumes double that?
mike
#1123
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
ORIGINAL: alfredbmor
Neat, congratulations jglemba
Neat, congratulations jglemba
#1124
My Feedback: (4)
Join Date: Jan 2002
Location: Westhampton Beach,
NY
Posts: 860
Likes: 0
Received 0 Likes
on
0 Posts
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
Rereading the last few posts about servo location. As I am converting a once nitro powered Ulti into gas with the DLE,I take it I will need to relocate the servos to the rear?
Anyone have a pictures of their install so I can get an idea of what and how it was done?
Thanks,
Bill S.
Anyone have a pictures of their install so I can get an idea of what and how it was done?
Thanks,
Bill S.
#1125
RE: Carl Goldberg Ultimate 10-300 Brotherhood.
ORIGINAL: Twin_Flyer
Rereading the last few posts about servo location. As I am converting a once nitro powered Ulti into gas with the DLE,I take it I will need to relocate the servos to the rear?
Anyone have a pictures of their install so I can get an idea of what and how it was done?
Thanks,
Bill S.
Rereading the last few posts about servo location. As I am converting a once nitro powered Ulti into gas with the DLE,I take it I will need to relocate the servos to the rear?
Anyone have a pictures of their install so I can get an idea of what and how it was done?
Thanks,
Bill S.
The Goldberg ulitmate was built "ahead of it's time". It incorporated cut lite ply for weight like the newer models that are extremely light and strong like the "AJ Slick" and others like "Extreme", etc. Wish someone would kit this plane. We reasearched the cost of wood and kitting the plane and it would be to "pricey" to make using USA wood, covering, hardware, etc. Too bad!!! [&o]