replacement turnbuckles
#1
Junior Member
Thread Starter
Join Date: Jul 2004
Location: Newport News,
VA
Posts: 28
Likes: 0
Received 0 Likes
on
0 Posts
replacement turnbuckles
Its time to replace the turnbuckles on my LSt,and I want to know what everyone else uses.I know lunsford's TI ones are nice, but what else is out there?
Thanks for the onfo,
DanD
[:-]
Thanks for the onfo,
DanD
[:-]
#3
Senior Member
Join Date: Jun 2005
Location: Gotham City, NY
Posts: 1,720
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
Yes, get the Lunsford There is no others out there Have had a problem since upgrading, was breaking 1 per race weekend before. Now I just breal the screws that hold them in, which is still a PITA.
#4
Senior Member
Join Date: Oct 2004
Location: San Antonio,
TX
Posts: 4,867
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
Sounds to me like you need to use some [link=http://www.hexcrews.com/index.asp?PageAction=VIEWPROD&ProdID=612] HexHeads Hexscrews[/link]. I've never broken a screw and I use these.
#5
Senior Member
Join Date: Oct 2003
Location: Howell,
NJ
Posts: 475
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
I have the Lunsford ones also and the are terrific. But If you want a low cost option I have used this company before and their parts are very high quality.
[link=http://cgi.ebay.com/NEW-TEAM-LOSI-LST-BULLET-PROOF-TITANIUM-TURNBUCKLE-SET_W0QQitemZ6012307035QQcategoryZ44028QQrdZ1QQcmd ZViewItem]TEAM BLUESTAR[/link]
Plus these are titanium and guaranteed for life. I use a lot of Team Bluestar parts. They are high quality and very reasonable.
[link=http://cgi.ebay.com/NEW-TEAM-LOSI-LST-BULLET-PROOF-TITANIUM-TURNBUCKLE-SET_W0QQitemZ6012307035QQcategoryZ44028QQrdZ1QQcmd ZViewItem]TEAM BLUESTAR[/link]
Plus these are titanium and guaranteed for life. I use a lot of Team Bluestar parts. They are high quality and very reasonable.
#6
Senior Member
Join Date: Jun 2005
Location: Gotham City, NY
Posts: 1,720
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
2DMAX, I bought the RCScrewz set, are the ones you mentioned better? These stupid things always seem to break in the main, and on the inside rear, so it maes you take half the truck apart to change. I hate these thinks so much, I can't wait until I can upgrade to the LST2 rear arms without turnbucles, this is the single most thing I break (the screw, not the turnbuckle). I asked the LHS about better screws and they claimed there were none[:@]
#8
Senior Member
Join Date: Oct 2004
Location: San Antonio,
TX
Posts: 4,867
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
RCScrews are soft and weak, but won't rust. Hexscrews actually advertises their Rockwell Hardness (43) and Tensile strength (177,000 psi), I could not find this info on RCScrews site..... I've been using them since my Tmaxx (nightmare) days with excellent results.
#10
Senior Member
Join Date: Oct 2004
Location: San Antonio,
TX
Posts: 4,867
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
No, it's to the kit I use. I will try the new Armor versions soon though, I can't imagine them getting any better!!
I've taken to ordering bags of 100 for the common sizes..
I've taken to ordering bags of 100 for the common sizes..
#11
Senior Member
Join Date: Jun 2005
Location: Gotham City, NY
Posts: 1,720
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
I didn't see the Armor Plated version for the LST[] Only Mini-T. Did you break any prior to using them? I am ordering either way, not too fun when something stupid like that puts you out of races.
#12
Senior Member
Join Date: Jun 2005
Location: Gotham City, NY
Posts: 1,720
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
They don't appear to take PayPal I doubt my LHS can get them as they can't even figure out how to get Nova parts[&o] You know of a store that sells them that accepts PayPal?
#17
Senior Member
Join Date: Aug 2005
Location: Waterloo,
WI
Posts: 187
Likes: 0
Received 0 Likes
on
0 Posts
RE: replacement turnbuckles
I have the hexheds. Yesterday I was putting back on a turnbuckle and I think I broke the screw. Is there a relacement in the HexHeads?