RE: E Flight HABU 32- P-20SE Build thread+Videos*    Gallery
View related threads: (in this forum | in all forums)

Logged in as Guest



Users viewing this topic: none
    Search This Thread  
 
Printable Version

All Forums >> RC Airplanes >> RC Jets >> RE: E Flight HABU 32- P-20SE Build thread+Videos*
Page: <<   < prev  2 3 4 [5] 6 7 8 9 10 11   next >   >>  

Tower Hobbies Get Coupon Codes Brands  
Login
Message << Older Topic   Newer Topic >>
RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/5/2011 5:46 PM   
POWER JET


 

Posts: 218
Score: 100
Joined: 10/4/2009
Last Login: 5/21/2013
From: Athens, GREECE
Status: offline 		What about the landing?The manual says the flap-elevator mixing at full flaps is 2mm down elevator.is that correct to you or you're not using flaps? 
How many amp is the batteries you 're using?I think you must have two batteries...

_____________________________

No excuses...!

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 101

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/5/2011 6:16 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		There are pictures and video showing the landing...and the Flap setting!! I have more flap than the manual and more down too. Still need to measure the figures for my conversion manual.
One 1600Mah 2s Li-Po, on each ECU and Rx as the build information. I have on board gas using a micro gas tank which gives around 3 starts. Gas start is very low consumption.

Dave

Pictures show flap angles




Attachments
Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize


_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to POWER JET)
       Post #: 102

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/5/2011 8:06 PM   
Colin Gontier



Posts: 480
Score: 100
Joined: 4/1/2008
Last Login: 4/16/2013
From: Aylesbury, , UNITED KINGDOM
Status: offline 		Thanks for letting me play with the Habu ! When the original foam Habu came out it was amazing to fly a small foamie that handled so purely. This is definitely the next evolution of that concept, nice pure flying fun and a "proper" turbine model. I was impressed with the speed range - really nice and slow with the massive throw you've got on the flaps and it doesn't half zip along when throttle turned to "on"

Love it - can't wait to get mine. Next evolution will have twin booms for sure!

_____________________________

The home of Boomerang Jets - CARF Models - Jets Munt - Jetcat - Powerbox - Jet 1A - Jet Tronic - JR Propo

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 103

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/5/2011 8:11 PM   
bigplumbs



Posts: 2725
Score: 120
Joined: 7/29/2004
Last Login: 12/20/2011
From: England, , UNITED KINGDOM
Status: offline
quote:

ORIGINAL: gontflyer

Thanks for letting me play with the Habu ! When the original foam Habu came out it was amazing to fly a small foamie that handled so purely. This is definitely the next evolution of that concept, nice pure flying fun and a ''proper'' turbine model. I was impressed with the speed range - really nice and slow with the massive throw you've got on the flaps and it doesn't half zip along when throttle turned to ''on''

Love it - can't wait to get mine. Next evolution will have twin booms for sure!


Twin Booms and a little fibrglass fus as well would be nice

Dennis

_____________________________

It ain''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''

Hide Signatures

(in reply to Colin Gontier)
       Post #: 104

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/5/2011 8:20 PM   
J.F


 

Posts: 689
Score: 100
Joined: 4/28/2004
Last Login: 5/23/2013
From: Chichester, UNITED KINGDOM
Status: offline
quote:

ORIGINAL:
Next evolution will have twin booms for sure!


Boomerang Zepto would be cool for a p20

< Message edited by J.F -- 3/6/2011 10:59 AM >

Hide Signatures

(in reply to Colin Gontier)
       Post #: 105

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 2:37 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		Four more flights today on the Habu 32, Now 15 flights completed and reliability has been faultless, as expected.
Photo of fuel level and bubble trap after the last flight today, this flight was 6 min

Dw

Attachments
Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize


_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to J.F)
       Post #: 106

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 2:48 PM   
BaldEagel



Posts: 9351
Score: 118
Joined: 10/12/2005
Last Login: 5/24/2013
From: Wychling, Kent, UNITED KINGDOM
Status: offline 		Dave

I am amazed that you don't have any problems with the Tygon slipping off, I find if I don't wire tie mine on they just slip off or let air in, have you done something special to attach them?

Mike

_____________________________

No matter what anyone says 100% is the maximum you can get.

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 107

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 4:05 PM   
bigplumbs



Posts: 2725
Score: 120
Joined: 7/29/2004
Last Login: 12/20/2011
From: England, , UNITED KINGDOM
Status: offline
quote:

ORIGINAL: BaldEagel

Dave

I am amazed that you don't have any problems with the Tygon slipping off, I find if I don't wire tie mine on they just slip off or let air in, have you done something special to attach them?

Mike


The answer to this is very simple you use the correct size Tygon. The smaller size I tend to use on all engines up to a 18 lbler and I force it over the nipples and it never comes off.

Dennis

_____________________________

It ain''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''

Hide Signatures

(in reply to BaldEagel)
       Post #: 108

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 4:37 PM   
BaldEagel



Posts: 9351
Score: 118
Joined: 10/12/2005
Last Login: 5/24/2013
From: Wychling, Kent, UNITED KINGDOM
Status: offline 		Dennis

Does not matter what size Tygon I use once the oil and fuel gets on it, or under it they slip off, learnt this a long time ago with my petrol engines, can't say Kero is any different.

Mike

_____________________________

No matter what anyone says 100% is the maximum you can get.

Hide Signatures

(in reply to bigplumbs)
       Post #: 109

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 4:46 PM   
bigplumbs



Posts: 2725
Score: 120
Joined: 7/29/2004
Last Login: 12/20/2011
From: England, , UNITED KINGDOM
Status: offline
quote:

ORIGINAL: BaldEagel

Dennis

Does not matter what size Tygon I use once the oil and fuel gets on it, or under it they slip off, learnt this a long time ago with my petrol engines, can't say Kero is any different.

Mike


Seems odd to me cos mine holds on like you would not believe. Perhaps there are different typws of Tygon. It you were to try to pull mine off even a straight pipe you would have one heck of a job. I do however use the very small size though.

Dennis

_____________________________

It ain''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''

Hide Signatures

(in reply to BaldEagel)
       Post #: 110

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 5:00 PM   
J.F


 

Posts: 689
Score: 100
Joined: 4/28/2004
Last Login: 5/23/2013
From: Chichester, UNITED KINGDOM
Status: offline 		Not sure what size tygon or nipples I use but on gas and with jeta never had one come off or leak. They are on very tight.

Hide Signatures

(in reply to bigplumbs)
       Post #: 111

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 5:14 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline
quote:

ORIGINAL: BaldEagel

Dave

I am amazed that you don't have any problems with the Tygon slipping off, I find if I don't wire tie mine on they just slip off or let air in, have you done something special to attach them?

Mike


Mike

Never wired any of my models, never had a leak! Only use 3.2mm bore 1/8" 4040 Tygon. Once it's been on 24 hours, I would have to put my foot on the tank and stretch with all my strength to get off. What I actually do if I need to remove is "pinch" the tube with bull nose pliers to ravel, then it comes off. Never Never cut it off!
I'm guessing you use straight brass tube, no barb? The nipples I use on this tank are 4.8mm at the barb point, on 5/32" (4mm) brass tube pipes I slip a Dubro solder barb over, these are 5.3mm over the point of the barbs... I think I sent you some free barbs with the ducty tank?They were the 1/8 pipe size ones?
The clunk line in this tank is 1/4" od 4040 tygon with a felt clunk, the line is only 82mm long-Even I thought it might be too short, but as shown by the pixs after a flight with rolls, loops, spins, inverted it's working fine...

Dave

_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to BaldEagel)
       Post #: 112

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 5:35 PM   
bigplumbs



Posts: 2725
Score: 120
Joined: 7/29/2004
Last Login: 12/20/2011
From: England, , UNITED KINGDOM
Status: offline 		Just ordered my Habu 32 with the e flite electric retracts. I am going to go electric first with the recommended setup (Cost £120 excl batt and a cheaper ESC) then if I like it I will bite the bullet and put in a P20 or if I like it electric too much buy another and put in a P20. These certainly are a good little plane.


Dennis

PS The virus on this site continues to be a pain I think it is worse if you hit the quote option

_____________________________

It ain''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''''

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 113

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 6:21 PM   
BaldEagel



Posts: 9351
Score: 118
Joined: 10/12/2005
Last Login: 5/24/2013
From: Wychling, Kent, UNITED KINGDOM
Status: offline 		Dave

I do barb my copper pipes, usually I solder a piece of paper clip around the tube and tie behind that, perhaps the barbs are better at holding the Tygon on, I have used the Dubro barbs, but found them difficult to get hold of, will have to try harder to get hold of some and try them on my Kero installations, only ever used them on Petrol previously. I did not find any barbs in with the Ducty tank, perhaps I missed them in the packaging, I have to admit the size of the box was a bit of supprise.

Mike

_____________________________

No matter what anyone says 100% is the maximum you can get.

Hide Signatures

(in reply to bigplumbs)
       Post #: 114

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 6:52 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		Mike

The have multiple ridge/rings, so each of these add a seal, plus they are perfectly round.
We keep both sizes in stock ;-) guess something else to add to the web shop-only another 2000 products and we will be there!
Thought I put them in with the tank package...maybe it was another, too old to remember for sure...

Dave

_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to BaldEagel)
       Post #: 115

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 10:09 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		Video done by a club member on saturday early before the sky cleared. Thanks Nige who posted it on another site. camera was a flip screen family holiday job, not brilliant quality, but shows bits.

http://www.youtube.com/watch?v=zqJG1pYt6Lw

_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 116

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/6/2011 10:42 PM   
smaze17


 

Posts: 1137
Score: 105
Joined: 12/14/2001
Last Login: 5/23/2013
From: CALABASAS, CA, USA
Status: online 		Very nice Dave....well done!! Mine is supposedly arriving March 21 at my LHS.

-S

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 117

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/7/2011 7:51 AM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		Lots of people waiting on this one

Dave

_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to smaze17)
       Post #: 118

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/8/2011 11:15 AM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		Just found time to charge the Habu 32 Rx Li-Po after 12 flights Saturday/Sunday and it used 394mAh total, so with a 1600mAh Rx battery that's at least 40 flights on a charge.

Dw

Attachments
Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize


_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 119

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/8/2011 11:43 AM   
Henke Torphammar



Posts: 1330
Score: 100
Joined: 10/9/2002
Last Login: 5/23/2013
From: Ljungby, SWEDEN
Status: offline
quote:

ORIGINAL: Dave Wilshere

Just found time to charge the Habu 32 Rx Li-Po after 12 flights Saturday/Sunday and it used 394mAh total, so with a 1600mAh Rx battery that's at least 40 flights on a charge.

Dw


How much does the ECU/pump use per flight? (gas or kerostart?)

_____________________________

/Henke
www.youtube.com/henke2
Swist F5D, Lambert Kolibri T25 - 310mph 2012

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 120

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/8/2011 12:45 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		As the post on the previous page, I seem to be using 75-85mAh per flight on the ECU (Gas start) I have a 1600mAh pack on that too.

Dave

_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to Henke Torphammar)
       Post #: 121

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/8/2011 1:41 PM   
Henke Torphammar



Posts: 1330
Score: 100
Joined: 10/9/2002
Last Login: 5/23/2013
From: Ljungby, SWEDEN
Status: offline 		ah, sorry I missed that part. Alot of numbers, digi switches here and there For the smaller more weight sensitive airframes two 350mah packs would be enough for a couple of flights too then.

_____________________________

/Henke
www.youtube.com/henke2
Swist F5D, Lambert Kolibri T25 - 310mph 2012

Hide Signatures

(in reply to POWER JET)
       Post #: 122

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/8/2011 1:48 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		Henke

Yes, I fly things like my CARF Spark with 480mAh 2s pack and get 4 flights easy. Powerbox switches are great.

The Habu 32 needs the weight, so bigger batteries make sense.

Dave

_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to Henke Torphammar)
       Post #: 123

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/11/2011 12:05 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		Another batch of 20 Habu 32 tail pipes just arrived today, perfect timing for more European orders going out.
Pix of the tail pipe/turbine today after around 17 runs

Dw

Attachments
Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize


_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 124

RE: E Flight HABU 32- P-20SE Build thread+Videos* - 3/13/2011 10:17 PM   
Dave Wilshere


 

Posts: 6271
Score: 108
Joined: 6/12/2002
Last Login: 5/23/2013
From: Watford, UNITED KINGDOM
Status: offline 		First time off tarmac today with the Habu 32, five more flights. Package really has worked out very well, totally reliable model. Only comment would be need for light colour on the wing/tail LE as everything is dark and on days like today it disappears coming towards you.
Dw

Attachments
Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize 		Click to see fullsize image.
Click for fullsize
Click to see fullsize image.
Click for fullsize


_____________________________

Motors & Rotors. JetCat, Powerbox, Intairco, Behotec, Graupner. CARF-models Rep. JR Propo for ever!, Jet 1A, MAP, Evojet, BV

Hide Signatures

(in reply to Dave Wilshere)
       Post #: 125

Page:   <<   < prev  2 3 4 [5] 6 7 8 9 10 11   next >   >>  
All Forums >> RC Airplanes >> RC Jets >> RE: E Flight HABU 32- P-20SE Build thread+Videos*
Page: <<   < prev  2 3 4 [5] 6 7 8 9 10 11   next >   >>  




Jump to:


 
Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America


1.203RCU1