Exceed RC G2    Gallery
View related threads: (in this forum | in all forums)

Logged in as Guest



Users viewing this topic: none
    Search This Thread  
 
Printable Version



All Forums >> RC Helicopters >> Exceed RC Support - Helicopter >> Exceed RC G2
Page: [1]

Tower Hobbies Get Coupon Codes Brands  
Login
Message << Older Topic   Newer Topic >>
Exceed RC G2 - 4/1/2011 11:04 PM   
mvn1982


 

Posts: 1
Score: 100
Joined: 4/1/2011
Last Login: 4/10/2011
From: Las Vegas, NV, USA
Status: offline 		I just purchased a Exceed RC G2, and I am pretty new to this. I thought I would be just able to learn how to fly it as i went but that hasn't worked out for me so far. I have only been able to get the heli off the ground a few times but havent felt to comfortable getting it more than a couple inches off the ground at a time. I wasn't expecting it to be so complicated when i purchased it and now I feel that I might have bought more helicopter than I can handle now with my limited skill level. Is there a website that I can go to that will explain all the terms and settings for heli's? I don't want to give up trying to learn how to fly it, but I am feeling a little frustrated now. Also when I put the throttle above 60% the tail rotor shakes back and forth...what is the best way to fix this?? Any replies will be greatly appriciated as I am completely new to 3D heli's. Thanks.

Hide Signatures
       Post #: 1

RE: Exceed RC G2 - 4/13/2011 9:07 PM   
Forum support1


 

Posts: 268
Score: 105
Joined: 9/28/2010
Last Login: 2/5/2013
From: la puente, CA, UNITED KINGDOM
Status: offline 		Hi

can you use a voltmeter and check your battery maybe one of the cells is death.

Eric

Hide Signatures

(in reply to mvn1982)
       Post #: 2

RE: Exceed RC G2 - 6/18/2011 6:44 AM   
hvhooch


 

Posts: 31
Score: 100
Joined: 5/4/2011
Last Login: 3/11/2013
From: Belleville, IL, USA
Status: offline 		Buy a 6 channel simulator....and practice...practice...practice........it will take a good couple of weeks or so to get used to flying 6 channel......also look at youtube.........very use stuff to learn......make sure all linkage is straight and not bent........check the pitch on blades......check everything.....buy a crash kit.....check trims.......make sure the are set right........start off with 50% throttle........make sure tail is adjusted at this point.......not spinning and you have a good hold......then a little more power......a couple of inches off ground you should be able to adjust trims...but do this slowly on a flat surface in an open area......once you have heli trimmed out...start hopping.........do this for a week.....then go fowards a little.....tail in..........land...keep doing this..........the rst will come to you......it takes alot of time and patience to become a good flyer.......watch the videos that Xheli make......all of them.......ou can learn alot from those guys......... 

Hide Signatures

(in reply to mvn1982)
       Post #: 3

RE: Exceed RC G2 - 6/18/2011 6:51 AM   
hvhooch


 

Posts: 31
Score: 100
Joined: 5/4/2011
Last Login: 3/11/2013
From: Belleville, IL, USA
Status: offline 		check your gain on the TX.........too much will make tail jerk back and forth........RUDD MIX.....I think it is the left knob.....all the way to the left will make tail jerky.........I keep mine at about 9 o'clock or so......you will know when its right....
 

Hide Signatures

(in reply to mvn1982)
       Post #: 4

Page:   [1]
All Forums >> RC Helicopters >> Exceed RC Support - Helicopter >> Exceed RC G2
Page: [1]





Jump to:


 
Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America


0.297RCU1