2nd Build,new step hull (Full Version)

All Forums >> [RC Boats] >> RC Airboats

Message

---

Don1028 -> 2nd Build,new step hull (4/19/2011 5:24 AM) This is the start of my second airboat.My first boat was a flat bottom boat built from blue styrofoam and coated with fiberglass cloth and epoxy resin.The boat ran great but I was looking for something more stable in the turns so a larger boat is being built.This boat is being constructed of 1/8" birch plwood with a stepped bottom and a dropped rear deck area with both width and length being greater than the first boat.The first picture is of the original boat with the rest being the new boat

---

Don1028 -> RE: 2nd Build,new step hull (4/19/2011 5:25 AM)

---

asmithnc -> RE: 2nd Build,new step hull (4/19/2011 2:16 PM) Nice work Don..... Go GATORS

---

Mikeup -> RE: 2nd Build,new step hull (4/19/2011 3:24 PM) The red air boat dimensions, if you don't mind. That is a beautiful boat!!! The only thing i spot is transom heavy. The RED would be a good canidate for electric outrunner like a Balsa 2810-9 motor as a puller. I have several homemade airboats on electric power as gas on ponds here are outlawed ( noise ). The RED is smooth looking and sharp looking. Mine aren't lookers but are functionable and i have FUN!!!

---

Don1028 -> RE: 2nd Build,new step hull (4/21/2011 2:10 AM) The dimensions of the red boat are approximately 41"x23" with the bottom being 17" wide.The new boat is approximately 44"x 25" with the bottom being 21" wide.

---

ptr34 -> RE: 2nd Build,new step hull (4/21/2011 2:26 AM) looking good hope to see u may 14 and 15 at meet

---

Don1028 -> RE: 2nd Build,new step hull (7/29/2011 4:15 AM) Here are some more pictures of the boat hull.Final paint and assembly will begin this weekend.Looking forward to test running the new boat in the next week or two.Thanks to everyone on this forum for the different ideas and designs in each threadThe general looks of the boat came from pictures on Cajun Gators web site with the cage and engine stand coming from Mudmasher Airboats.

---

dadkins -> RE: 2nd Build,new step hull (7/29/2011 4:01 PM) Looking good Don, What are you doing for a paint scheme - I imagine the white is primer?

---

Don1028 -> RE: 2nd Build,new step hull (7/29/2011 5:21 PM) Thanks for looking.The last two pictures are of the boat in primer.The boat is gong to be yellow and white.The bottom of the boat and cage will be yellow with the top being a combination of white and yellow.

---

Don1028 -> RE: 2nd Build,new step hull (10/24/2011 12:19 AM) Here are some pictures of the finished boat

---

Don1028 -> RE: 2nd Build,new step hull (10/24/2011 12:22 AM) More pictures

---

Mikeup -> RE: 2nd Build,new step hull (10/24/2011 2:24 AM) Shame on if you put it in the water. W  O   W   !  I wish i could build like that. Mine are basic airboats but are functional.

---

Got RPM -> RE: 2nd Build,new step hull (10/24/2011 3:58 AM) A truly beautiful build! Have you run it yet? .

---

RS 38-40 -> RE: 2nd Build,new step hull (10/24/2011 10:47 PM) Very nice build .I like what you did with the rudder hook up . I hadn't seen it done that way before .

---

Page: [1] 1

SITE MAP!   : :   FORUM RULES RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

0.421875