Backup/Redundant batteries    Gallery
View related threads: (in this forum | in all forums)

Logged in as Guest



Users viewing this topic: none
    Search This Thread  
 
Printable Version

All Forums >> Electric Aircraft Universe >> Electric Pattern Aircraft >> Backup/Redundant batteries
Page: [1] 2   next >   >>  

Tower Hobbies Get Coupon Codes Brands  
Login
Message << Older Topic   Newer Topic >>
Backup/Redundant batteries - 1/30/2012 12:57 AM   
OhD


 

Posts: 853
Score: 100
Joined: 10/24/2002
Last Login: 5/22/2013
From: west hills, CA, USA
Status: offline 		We recently had an interesting discussion on the NSRCA pattern list concerning backup batteries. The power supply is the first thing we think of when we have trouble so it would be nice to eliminate it as a source of catastrophic failure. I don’t know who should get credit for the concept but I got interested when Chris Moon suggested making up a special voltage regulator that would connect to the balance connector of the motor pack, tapping off the bottom two cells. I suggested just making a simple cable that could be connected to any voltage regulator and these are now available from F3A Unlimited.

The way I configured my system was to build a simplified version of my Perfect Switch Harness that would allow me to connect an onboard voltmeter so I could read the voltage of the two cells when I installed the motor battery. This would assure me I had installed a charged battery. I have been carrying around an Eagle Tree data logger and display to provide this info. You only need to take off once with a perfectly good but discharged battery and come down with a bad battery, to wish you had been more careful. I set the output of this regulator to 6.3 volts so the system would not draw current from my receiver pack which is regulated to 6.0 volts. I then charged my receiver pack to the storage voltage and haven’t charged it since.

Then one of the guys at the field says how do you know you aren’t using up the capacity of the receiver pack so I went home and installed a voltmeter that would read both. The photo shows the results.

Jim O

Attachments
Click to see fullsize image.
Click for fullsize


Hide Signatures
       Post #: 1

RE: Backup/Redundant batteries - 1/31/2012 11:37 AM   
serious power


 

Posts: 572
Score: 100
Joined: 11/19/2007
Last Login: 5/24/2013
From: wexford, IRELAND
Status: offline 		Hi Jim,
Clever !!
Between you and Chris you have come up with a great idea.
I use an Emcotec dual batt,, switch/reg,, . It monitors both batt's and takes from the highest voltage source.
I don't see anything wrong with keeping the rx batt,, charged ,using the emcotec ie, so that the 10s is kept for the motor when capacity is tight. eg using a 4400.
The Emcotec gives a flashing led warning if one or both batt's are low in voltage, separate/different warnings I think - I will check.

Brian


Hide Signatures

(in reply to OhD)
       Post #: 2

RE: Backup/Redundant batteries - 1/31/2012 11:40 AM   
serious power


 

Posts: 572
Score: 100
Joined: 11/19/2007
Last Login: 5/24/2013
From: wexford, IRELAND
Status: offline 		Double post - RCU ??? Timeout error ??

Hide Signatures

(in reply to OhD)
       Post #: 3

RE: Backup/Redundant batteries - 1/31/2012 4:48 PM   
OhD


 

Posts: 853
Score: 100
Joined: 10/24/2002
Last Login: 5/22/2013
From: west hills, CA, USA
Status: offline 		Brian, one of the greatest considerations when adding a redundant or backup battery is weight. By using the motor battery as the primary source one can use a very small backup receiver pack. The smallest I had was 800mAh but one could go even smaller. Most of us draw less than 100 mAh per flight so even a 300mAh pack would work. You might find that you could go to a larger motor pack with no additional weight if you went to this system. And I don't see why you couldn't use your existing Emcotec device. That is why I recommended just building an adapter cable because most folks already have the other components required.

Jim O

Hide Signatures

(in reply to serious power)
       Post #: 4

RE: Backup/Redundant batteries - 1/31/2012 5:20 PM   
serious power


 

Posts: 572
Score: 100
Joined: 11/19/2007
Last Login: 5/24/2013
From: wexford, IRELAND
Status: offline 		Jim,
I routinely fly with a 250 or 370 on their own. I use 45 to 55mAh per P flight.
I have my eye on a 160mAh right now - for comp flights.
This is for a big bi-plane to make weight.
I will be doing this and testing with recharging frequencies, ie; after 1 flight,2 flights,3 flights etc.
Hugs and kisses !!

Brian


Hide Signatures

(in reply to OhD)
       Post #: 5

RE: Backup/Redundant batteries - 1/31/2012 5:27 PM   
nonstoprc



Posts: 2337
Score: 110
Joined: 9/9/2003
Last Login: 5/24/2013
From: Central, TX, USA
Status: offline 		On tap into the power pack as the backup source, just wonder if somebody has experience doing so with CC ice hv. Any chance of interference from the ESC?

_____________________________

Where facts are few, experts are many.
Perfection is God''''s business.

Hide Signatures

(in reply to serious power)
       Post #: 6

RE: Backup/Redundant batteries - 1/31/2012 7:32 PM   
J-P


 

Posts: 204
Score: 100
Joined: 10/22/2004
Last Login: 5/21/2013
From: Saint Nom , FRANCE
Status: offline
quote:

ORIGINAL: serious power

I use an Emcotec dual batt,, switch/reg,, . It monitors both batt's and takes from the highest voltage source.

Brian




Are you sure ?
Below is the Emcotec DPSI Micro – DualBat spec.

The DPSI Micro – DualBat serves as redundant power supply in RC models. Redundancy is accomplished through two connected batteries. If one battery fails, safe operation is assured by the second battery. Usually both batteries are equally discharged. Furthermore, due to both batteries being “parallel”, current drawn from the batteries is cut in half; therefore, batteries with lower capacity can be utilized.

Hide Signatures

(in reply to serious power)
       Post #: 7

RE: Backup/Redundant batteries - 1/31/2012 7:55 PM   
rgreen24



Posts: 962
Score: 100
Joined: 1/22/2002
Last Login: 5/23/2013
From: Omaha, NE, USA
Status: offline 		Jim, can you explain how you would tap in into the 10s batteries to power the rx? Is this something that you are going to sell possibly?


Thanks,

Hide Signatures

(in reply to J-P)
       Post #: 8

RE: Backup/Redundant batteries - 1/31/2012 8:08 PM   
serious power


 

Posts: 572
Score: 100
Joined: 11/19/2007
Last Login: 5/24/2013
From: wexford, IRELAND
Status: offline 		''Hint:
For the DPSI Micro - DualBat, two identical batteries must be used, i.e. same
type (NiCad/NiMH or LiPo) and same cell number. The capacity may vary – even
if this does not make sense.''

Another quote from the manual !
It has completely separate pathways for each batt,,.
It will take from the higher voltage source at all times, therefore normally maintaining an equal voltage batt 1 to batt 2.
It has separate and combined low voltage warnings.
The manual is a German to English translation - some quirky phrases result.

Brian

Hide Signatures

(in reply to J-P)
       Post #: 9

RE: Backup/Redundant batteries - 1/31/2012 9:26 PM   
J-P


 

Posts: 204
Score: 100
Joined: 10/22/2004
Last Login: 5/21/2013
From: Saint Nom , FRANCE
Status: offline 		I just downloaded the manual here

http://shop.rc-electronic.com/e-vendo.php?shop=k_emcotec_e&SessionId=&a=article&ProdNr=A11053&t=6&c=541&p=541

but did not found the explanations you are mentioning on the french or english version.

The idea to use a DPSI Micro DualBat 5.9V/7.2V or a POWERBOX™ ELECTRONIC SWITCH with one 450 Mah RX batt and 2 cells from the 10S packs looks great.

Due to the bad weather, I can't do some inflight test, so hope somebody will give it a try pretty soon

J-P

Hide Signatures

(in reply to serious power)
       Post #: 10

RE: Backup/Redundant batteries - 1/31/2012 9:44 PM   
jlkonn



Posts: 1418
Score: 100
Joined: 1/2/2003
Last Login: 1/26/2013
From: Back home in, OH, USA
Status: offline 		Robert,
Chris Moon sells the "pigtail" to do it now.
See the F3A Unlimited website.
JLK

_____________________________

A goal without a plan is just a dream.
AMA 97605

Hide Signatures

(in reply to rgreen24)
       Post #: 11

RE: Backup/Redundant batteries - 1/31/2012 10:31 PM   
serious power


 

Posts: 572
Score: 100
Joined: 11/19/2007
Last Login: 5/24/2013
From: wexford, IRELAND
Status: offline
quote:

ORIGINAL: J-P

I just downloaded the manual here

http://shop.rc-electronic.com/e-vendo.php?shop=k_emcotec_e&SessionId=&a=article&ProdNr=A11053&t=6&c=541&p=541

but did not found the explanations you are mentioning on the french or english version.

The idea to use a DPSI Micro DualBat 5.9V/7.2V or a POWERBOX™ ELECTRONIC SWITCH with one 450 Mah RX batt and 2 cells from the 10S packs looks great.

Due to the bad weather, I can't do some inflight test, so hope somebody will give it a try pretty soon

J-P


2 more quotes from the English version;

''Decoupling of both batteries in the DPSI Micro - DualBat and the
electronically switches are completely separated (inclusively peripheral
electronics) and therefore duplicated. No twin diodes (i.e. two diodes in
one housing) are being used. Malfunction of one part does not lead to
a total loss of the system. This circuitry has proven in many thousand
systems already.''

3. Low Voltage Battery 2: ⎯ ⎯ ⎯ ⎯⎯⎯⎯⎯ ⎯⎯⎯⎯⎯
DualBat ONLY error signal: LED blinks 3 x 0.05s on with 0.05s
breaks each, then 2 x 0.8s on with 0.4s break
If the voltage of battery 2 drops below a certain value, this blinking
code is output. The capacity of the battery usually suffices for one
more flight before recharging is necessary. This error code is also
repeated in a sequence of 6 seconds. If the error is qualified once, it
stays active until turning the DPSI off.
If both batteries of the DPSI Micro - DualBat indicate low voltage, both
error codes are output alternatively.

Take time to read the manual - it is a translation - could be worse, could be French to English !

Brian

Hide Signatures

(in reply to J-P)
       Post #: 12

RE: Backup/Redundant batteries - 1/31/2012 10:35 PM   
OhD


 

Posts: 853
Score: 100
Joined: 10/24/2002
Last Login: 5/22/2013
From: west hills, CA, USA
Status: offline
quote:

ORIGINAL: rgreen24

Jim, can you explain how you would tap in into the 10s batteries to power the rx? Is this something that you are going to sell possibly?


Thanks,


I used the male half of Futaba extension and spliced it to a balance connector adapter. The Black wire attaches to the pin with the black wire on the balance connector which we'll call pin one, and the red wire then attaches to pin three. Perform a test before you connect it to anything. The output should look exactly like a 2s LiPo.

Jim

Attachments
Click to see fullsize image.
Click for fullsize


Hide Signatures

(in reply to rgreen24)
       Post #: 13

RE: Backup/Redundant batteries - 1/31/2012 10:38 PM   
OhD


 

Posts: 853
Score: 100
Joined: 10/24/2002
Last Login: 5/22/2013
From: west hills, CA, USA
Status: offline 		Here is another shot.

Jim O

Attachments
Click to see fullsize image.
Click for fullsize


Hide Signatures

(in reply to OhD)
       Post #: 14

RE: Backup/Redundant batteries - 1/31/2012 11:27 PM   
rgreen24



Posts: 962
Score: 100
Joined: 1/22/2002
Last Login: 5/23/2013
From: Omaha, NE, USA
Status: offline 		Thanks Jim, how are you,regulating the voltage from the motor battery.
Good to see that your back JLK

Hide Signatures

(in reply to OhD)
       Post #: 15

RE: Backup/Redundant batteries - 1/31/2012 11:51 PM   
OhD


 

Posts: 853
Score: 100
Joined: 10/24/2002
Last Login: 5/22/2013
From: west hills, CA, USA
Status: offline
quote:

ORIGINAL: rgreen24

Thanks Jim, how are you,regulating the voltage from the motor battery.
Good to see that your back JLK



Jaccio Perfect Switch Harness set to 6.3 volts. See first post in thread.

Jim

Hide Signatures

(in reply to rgreen24)
       Post #: 16

RE: Backup/Redundant batteries - 2/1/2012 12:14 AM   
rgreen24



Posts: 962
Score: 100
Joined: 1/22/2002
Last Login: 5/23/2013
From: Omaha, NE, USA
Status: offline 		Thanks Jim, just re-read the first post and it all makes sense now.

Thanks

Hide Signatures

(in reply to OhD)
       Post #: 17

RE: Backup/Redundant batteries - 2/1/2012 8:19 PM   
J-P


 

Posts: 204
Score: 100
Joined: 10/22/2004
Last Login: 5/21/2013
From: Saint Nom , FRANCE
Status: offline
quote:

ORIGINAL: serious power

''Hint:
For the DPSI Micro - DualBat, two identical batteries must be used, i.e. same
type (NiCad/NiMH or LiPo) and same cell number. The capacity may vary – even
if this does not make sense.''

Another quote from the manual !
It has completely separate pathways for each batt,,.
It will take from the higher voltage source at all times, therefore normally maintaining an equal voltage batt 1 to batt 2.
It has separate and combined low voltage warnings.
The manual is a German to English translation - some quirky phrases result.

Brian



Sorry, but I didn't found these explanations on the Emcotec site.
Maybe you have a link .....

http://www.rc-electronic.com/downloads/pdf/bedienungsanleitungen/Anleitung_DPSI_Micro_2009_EN.pdf
The DPSI Micro – DualBat serves as redundant power supply in RC models. Redundancy is accomplished through two connected batteries. If one battery fails, safe operation is assured by the second battery. Usually both batteries are equally discharged. Furthermore, due to both batteries being “parallel”, current drawn from the batteries is cut in half; therefore, batteries with lower capacity can be utilized.

Hide Signatures

(in reply to serious power)
       Post #: 18

RE: Backup/Redundant batteries - 2/1/2012 9:04 PM   
serious power


 

Posts: 572
Score: 100
Joined: 11/19/2007
Last Login: 5/24/2013
From: wexford, IRELAND
Status: offline
quote:

ORIGINAL: J-P


quote:

ORIGINAL: serious power

''Hint:
For the DPSI Micro - DualBat, two identical batteries must be used, i.e. same
type (NiCad/NiMH or LiPo) and same cell number. The capacity may vary – even
if this does not make sense.''

Another quote from the manual !
''''It has completely separate pathways for each batt,,.
It will take from the higher voltage source at all times, therefore normally maintaining an equal voltage batt 1 to batt 2.
It has separate and combined low voltage warnings.
The manual is a German to English translation - some quirky phrases result.'''' MY WORDS NOT IN THE PDF.

Brian



Sorry, but I didn't found these explanations on the Emcotec site.
Maybe you have a link .....

http://www.rc-electronic.com/downloads/pdf/bedienungsanleitungen/Anleitung_DPSI_Micro_2009_EN.pdf
The DPSI Micro – DualBat serves as redundant power supply in RC models. Redundancy is accomplished through two connected batteries. If one battery fails, safe operation is assured by the second battery. Usually both batteries are equally discharged. Furthermore, due to both batteries being “parallel”, current drawn from the batteries is cut in half; therefore, batteries with lower capacity can be utilized.


J-P,
Yes that's the one.
My quotes are from the same document. Just check carefully. - See page 10 first paragraph, see page 20 first 'hint' and see page 24 'Error Indication'
I think you have focused on ''parallel''.
Where they say ''parallel'' it's in '' '' because they are speaking metaphorically (or it's a simile).
In your quote ,which is in the same pdf file, they also say 'If one battery fails, safe operation is ''assured'' by the second battery.
If the batteries were in 'parallel' this would NOT be possible.
Hope this helps

Brian



Hide Signatures

(in reply to J-P)
       Post #: 19

RE: Backup/Redundant batteries - 2/1/2012 9:37 PM   
J-P


 

Posts: 204
Score: 100
Joined: 10/22/2004
Last Login: 5/21/2013
From: Saint Nom , FRANCE
Status: offline 		It's not really clear ....
And what about Hint @ page 20 ?

Hint:
Supply of a DPSI Micro – DualBat with one battery and a BEC-Supply as second battery instead is not possible!

Hide Signatures

(in reply to serious power)
       Post #: 20

RE: Backup/Redundant batteries - 2/1/2012 10:00 PM   
serious power


 

Posts: 572
Score: 100
Joined: 11/19/2007
Last Login: 5/24/2013
From: wexford, IRELAND
Status: offline 		Hi J-P,
Sometimes we see what we want and do not see the rest.
That 'Hint' says a 'bec' !!
The guys are talking about a 2nd battery , all be it a BIG one or in fact 2 cells from a BIG battery.
I will leave you to work it out.

Edit; I believe that the Emcotec Dual batt unit is the ideal way to use Chris's and Jim's idea - which is just brilliant for anyone that may be tight on the weight limit - like me.

Brian


Hide Signatures

(in reply to J-P)
       Post #: 21

RE: Backup/Redundant batteries - 2/2/2012 2:26 AM   
NJRCFLYER2


 

Posts: 819
Score: 102
Joined: 7/28/2004
Last Login: 5/19/2013
From: Randolph, NJ, USA
Status: offline 		Well actually, the idea has been around a little while longer than you may think,but that's OK:

http://www.rcuniverse.com/forum/m_9484625/anchors_9485156/mpage_1/key_/anchor/tm.htm#9485156



_____________________________

Ed Alt
Tech-Aero Designs LLC

Hide Signatures

(in reply to serious power)
       Post #: 22

RE: Backup/Redundant batteries - 2/2/2012 3:24 AM   
OhD


 

Posts: 853
Score: 100
Joined: 10/24/2002
Last Login: 5/22/2013
From: west hills, CA, USA
Status: offline
quote:

ORIGINAL: NJRCFLYER2

Well actually, the idea has been around a little while longer than you may think,but that's OK:

http://www.rcuniverse.com/forum/m_9484625/anchors_9485156/mpage_1/key_/anchor/tm.htm#9485156




I had started writing a post to ask someone to jump in and tell us who really came up with the idea. The "idea" is to tap the pack at the balance connector. I quickly reviewed the referenced thread in RCU but still don't see a reference to tapping the pack at the balance connector. Maybe I missed it but I still don't know who to give credit to.

Jim O

Hide Signatures

(in reply to NJRCFLYER2)
       Post #: 23

RE: Backup/Redundant batteries - 2/2/2012 3:34 AM   
OhD


 

Posts: 853
Score: 100
Joined: 10/24/2002
Last Login: 5/22/2013
From: west hills, CA, USA
Status: offline
quote:

ORIGINAL: serious power

Hi J-P,
Sometimes we see what we want and do not see the rest.
That 'Hint' says a 'bec' !!
The guys are talking about a 2nd battery , all be it a BIG one or in fact 2 cells from a BIG battery.
I will leave you to work it out.

Edit; I believe that the Emcotec Dual batt unit is the ideal way to use Chris's and Jim's idea - which is just brilliant for anyone that may be tight on the weight limit - like me.

Brian



This is the post I had started when I was interrupted by a phone call:

We need someone to jump in and tell us who came up with the idea originally to tap into the balance connector.

Regarding the Emcotec Dual Battery unit. It sounds as though the batteries are isolated from each other somehow but it is not clear how the one that is at a higher voltage will charge the one at the lower voltage. It sounds like it does and that could be a problem. If the motor battery gets too low the small receiver pack will try to recharge it. If this is so, it seems almost certain that the receiver pack would end up at 7.5 volts or so at the end of flight. Maybe that is okay as it is close to the storage voltage but if it goes much lower it won't provide much margin. What do you think?

Jim O

Hide Signatures

(in reply to serious power)
       Post #: 24

RE: Backup/Redundant batteries - 2/2/2012 3:43 AM   
jgg215


 

Posts: 195
Score: 105
Joined: 11/21/2004
Last Login: 5/24/2013
From: Albuquerque, NM, USA
Status: offline 		Jim,
We all know that good ideas are often developed independently but Keith Hoard and I both developed a balance plug redundant system on our own and used  it at the Nats. But who knows, it was probably done earlier by others....
See the thread on the NSRCA website for a discussion and description of potential problems:  

http://nsrca.us/forum/index.php?topic=167.0

John Gayer
Join the NSRCA


Hide Signatures

(in reply to OhD)
       Post #: 25

Page:   [1] 2   next >   >>  
All Forums >> Electric Aircraft Universe >> Electric Pattern Aircraft >> Backup/Redundant batteries
Page: [1] 2   next >   >>  




Jump to:


 
Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America


0.922RCU1