Glassing 1/7th scale P-51    Gallery
View related threads: (in this forum | in all forums)

Logged in as Guest



Users viewing this topic: none
    Search This Thread  
 
Printable Version



All Forums >> RC Airplanes >> Composites Fabrication And Repair >> Glassing 1/7th scale P-51 Page: [1]

Tower Hobbies Get Coupon Codes Brands  
Login
Message << Older Topic   Newer Topic >>
Glassing 1/7th scale P-51 - 11/18/2012 3:20 AM   
acdii


 

Posts: 2293
Score: 155
Joined: 1/31/2011
Last Login: 5/20/2013
From: Capron, IL, USA
Status: offline 		Im working on my Top Flite Gold Edition p-51 and want to glass the wing and fuse, but I dont know how much cloth to get for it, or what to use to make a hard surface. The balsa is so thin that Im afraid I will poke a hole in it just moving it around. I have some Z-poxy finishing resin, but I dont know if it will be enough for the entire plane.

I've been using Bondo auto resin to make molds and repair cowls, but I dont think it will be the correct stuff to use for the wings and fuse.


_____________________________

http://www.facebook.com/pages/B-17e-Desert-Rat-Restoration-Project/218159428244374

Hide Signatures
       Post #: 1

RE: Glassing 1/7th scale P-51 - 11/18/2012 4:37 AM   
speedracerntrixie


 

Posts: 2383
Score: 189
Joined: 6/7/2010
Last Login: 5/24/2013
From: San Jose, CA, USA
Status: offline 		The Z-poxy is good to use for glassing. When I do this I use 3/4 oz cloth. lay the cloth on the part to be covered, mix only enough resin that you can use in 20 min. pour some at the center of the part and sperad with an old credit card or Bondo spreader. Once all the cloth is saturated, blot with a paper towel to remove any excess resin as it only adds weight and makes it difficult to sand. When blotting, the use of a heat gun to warm up the resin really helps. Feather sand the edges of the privious sheet of glass before adding the next.  When it comes to the size sheets just think of it as you would an iron on covering. Always have between 65-70 degrees during application and cure. When fully cured, sand with 220 to smoothen out. There will be some visable  fabric weave if you blotted enough resin out, I wipe a thin coat of resin on the surface to fill the weave and sand a second time. At this point you should be ready for primer.


Hide Signatures

(in reply to acdii)
       Post #: 2

RE: Glassing 1/7th scale P-51 - 11/18/2012 5:20 AM   
sensei



Posts: 1502
Score: 176
Joined: 7/16/2002
Last Login: 5/24/2013
From: SAN ANTONIO, TX, USA
Status: offline 		All your really doing is sealing the balsa so you can paint and not read the balsa grain later. One ply of 3/4" along with Z-poxy will not keep you from damaging things from handling errors, and heavier cloths will add too much weight to fly worth keeping, so do yourself a favor and forget about using any kind of polyester or epoxy resin, keep it light and get yourself a can of Minwax polyurethane from Lowe's or Home Depot, place the 3/4" cloth down and brush on the Minwax, allow to dry, scuff sand with 320 grit, brush another coat Minwax repeated by sanding and your ready to start priming. This is simple, light, and the most cost effective way to prep for finish. measure length X width of everything and divide by 144, this will give you your SQ. FT. area of cloth to purchase.

Bob





_____________________________

Fly It Like You Stole It!!!

Hide Signatures

(in reply to speedracerntrixie)
       Post #: 3

RE: Glassing 1/7th scale P-51 - 11/18/2012 4:02 PM   
acdii


 

Posts: 2293
Score: 155
Joined: 1/31/2011
Last Login: 5/20/2013
From: Capron, IL, USA
Status: offline 		Well since it is a gas power plane and not glow, the minwax idea looks good, plus I have a few gallons of that already here.

OK I just had a really dumb idea pop up, Stain the plane Mahogany! It would look like one of those desk models made of wood. LOL

As far as the actual fabric, is it about the same equivalent of glass to monokote rolls, or would it be less?


_____________________________

http://www.facebook.com/pages/B-17e-Desert-Rat-Restoration-Project/218159428244374

Hide Signatures

(in reply to sensei)
       Post #: 4

RE: Glassing 1/7th scale P-51 - 11/18/2012 7:15 PM   
sensei



Posts: 1502
Score: 176
Joined: 7/16/2002
Last Login: 5/24/2013
From: SAN ANTONIO, TX, USA
Status: offline
quote:

ORIGINAL: acdii

Well since it is a gas power plane and not glow, the minwax idea looks good, plus I have a few gallons of that already here.

OK I just had a really dumb idea pop up, Stain the plane Mahogany! It would look like one of those desk models made of wood. LOL

As far as the actual fabric, is it about the same equivalent of glass to monokote rolls, or would it be less?



It will be the same SQ. FT. usage.

Bob

_____________________________

Fly It Like You Stole It!!!

Hide Signatures

(in reply to acdii)
       Post #: 5

RE: Glassing 1/7th scale P-51 - 11/22/2012 2:46 AM   
Luft-Gangster


 

Posts: 327
Score: 110
Joined: 12/30/2010
Last Login: 5/18/2013
From: Pinckney, MI, USA
Status: offline 		sensei  -  Great idea. Will put this to use this buliding season.
Thanks Leroy

Hide Signatures

(in reply to sensei)
       Post #: 6

Page:   [1]
All Forums >> RC Airplanes >> Composites Fabrication And Repair >> Glassing 1/7th scale P-51
Page: [1]





Jump to:


 
Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America


0.375RCU1