Sheet metal models?  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       

All Forums >> Radios, Batteries, Clubhouse and more >> Control Lines >> Sheet metal models?
Page: [1]

Login
Message << Older Topic   Newer Topic >>
Sheet metal models? - 11/1/2003 5:27:20 AM   
BMatthews



Posts: 8951
Joined: 10/4/2002
From: Burnaby, BC, CANADA
Status: offline 		For the past few days I stayed home from work to take advantage of the good weather we are having and try to get the vinyl siding on my porch before the winter storms hit with a vengeance. Along with this hateful task there's a fair bit of flashing to be applied. I got myself a big roll from the Home "Despot".

So it's evening now and I'm browsing some sites and what do I come across. A sheet metal CL model that uses the same aluminium flashing that I'm going to have left over after the job is done. It's Sheet Metal Susie and you can see her here at...

http://my.pclink.com/~dfritzke/sheetmetalsusie.pdf

So, I may have to just add another project to my list. This one would be built as a fun thing. I'll fly it now and then for giggles rather than performance. And in between times it'll look good hanging in the shop or eventually, if I ever have one, my den.


_____________________________

Bruce-
Proudly wasting balsa since 1965.

Free Flighters go that extra mile........
       Post #: 1

RE: Sheet metal models? - 11/1/2003 5:37:17 AM   
Jim Thomerson



Posts: 2825
Joined: 10/9/2002
From: Austin, TX, USA
Status: offline 		There was an all sheet metal Midget Mustang in Model Airplane news, back in the 50's I think. I also have a vague recollection of another article on building sheet metal airplanes. Sheet Metal Susie looks like an interesting project.

Jim

(in reply to BMatthews)
       Post #: 2

RE: Sheet metal models? - 11/1/2003 2:29:16 PM   
w8ye



Posts: 17492
Joined: 12/11/2001
From: Taylortown, OH, USA
Status: offline 		In the early 60's a neighbor gave me a plane very much like this that had a Enya .09 in it. The wings wern't finished and it seemed to heavy for a .09 so I removed the engine and used it in something else but it was a real novelty looking at it.

Enjoy,

jim

_____________________________

Attended the CutFinger Institute of DirtNap University for years but never did graduate....

Club Saito Member #7
Original AMA #31261

(in reply to Jim Thomerson)
       Post #: 3

RE: Sheet metal models? - 11/2/2003 8:29:56 AM   
William Robison



Posts: 20269
Joined: 11/10/2002
From: Mary Esther, Florida, FL, USA
Status: offline 		Bruce and the Jims:

In the late 50s there were several Jap kits with aluminum skins over a hardwood crutch for control line planes. They were too heavy to fly well, but they would fly. Almost the first ARFs other than Jim Walker's Firebaby and similar. Most were models of fighter planes, the one I remember in particular was a P-51.

Bill.

_____________________________

Real Airplanes have Two Engines
AMA 25139 - More than 40 years.

(in reply to w8ye)
       Post #: 4

RE: Sheet metal models? - 11/2/2003 12:53:31 PM   
Strat2003


 

Posts: 614
Joined: 3/9/2003
From: Mt. Pleasant, OH, AFGHANISTAN
Status: offline 		In the late 40's or early 50's there was a sheet metal speed model called a Topping 100. My dad saw one fly and said it made a noise something like a garbage can being struck by several ball peen hammers..........

(in reply to William Robison)
       Post #: 5

RE: Sheet metal models? - 11/6/2003 3:46:27 AM   
Steve Westphal



Posts: 110
Joined: 10/15/2002
From: Fremont, NE, USA
Status: offline 		I remember when I was growing up in the fifties, my father had an all aluminum P-51 Mustang. It was a C/L model and was magnificent. The motor looked like it was in the .29 to .35 range and it had never been flown. When my father started liquidating some of his collection, it was the first to go(about 1970). As I look back, I can't remember a brand name, but, the plane was stunning. I think he sold it for $700 or $800 back then(along with his mint, in the box, Morton M-5 which he sold for $500.) The Mustang was absolutely flawless and the aluminum shined brightly. Quite possibly, that plane, was responsible for my continued interest in the hobby today(although it's R/C now)! I will never forget it. The wingspan was about32 or 34 inches. Anyone remember it?

(in reply to BMatthews)
       Post #: 6

RE: Sheet metal models? - 11/7/2003 2:21:57 AM   
Rick Fair


 

Posts: 24
Joined: 10/17/2002
From: Springfield, IL, USA
Status: offline 		There is one of the Mustang C/L ones in pristine condition at the AMA museum in Muncie ...

(in reply to Steve Westphal)
       Post #: 7

RE: Sheet metal models? - 11/10/2003 1:42:27 AM   
FreeFlier


 

Posts: 46
Joined: 8/21/2003
From: Long Island's North Shore, NY, USA
Status: offline 		The Williams brothers (wheels/plastic engines,etc.) published several great all metal team race models in the 50s - I think. I've lost track of the issues, but those articles had detailed instructions on how to cut, shape, and rivet the metal panels, as well as how to build and fly the models.

They were truly craftsmen, and those models, and others of course, were part of what made me a lifetime model builder/flyer.

Thermals,

Stew

(in reply to Rick Fair)
       Post #: 8

Page:   [1]
All Forums >> Radios, Batteries, Clubhouse and more >> Control Lines >> Sheet metal models?
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

1.563RCU1