silicon anti-foaming agent  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       

All Forums >> Glow Engines, Gas Engines, Fuel & Mfg Support Forums >> RC Fuels >> silicon anti-foaming agent
Page: [1]

Login
Message << Older Topic   Newer Topic >>
silicon anti-foaming agent - 9/12/2004 9:02:01 AM   
geofferama


 

Posts: 280
Joined: 7/10/2004
From: Ginsburg, MD, USA
Status: offline 		I know everyone uses Armor All, but if its the silicone that's keeping the foam away, wouldn't any of the 'pure' silicone lubricant sprays accomplish the exact same task?

just curiosity, but i'd rather not kill my motor finding out
       Post #: 1

RE: silicon anti-foaming agent - 9/13/2004 3:00:31 AM   
downunder



Posts: 3114
Joined: 10/10/2002
From: Adelaide, AUSTRALIA
Status: offline 		Chances are it would work very well. Armor All certainly does the trick but the latest batch apparently doesn't have silicon anymore so an alternative would be nice to know about.

(in reply to geofferama)
       Post #: 2

RE: silicon anti-foaming agent - 9/13/2004 5:46:55 PM   
geofferama


 

Posts: 280
Joined: 7/10/2004
From: Ginsburg, MD, USA
Status: offline 		Well, i have this can of Kellog's Pure Silicone "Not Just Another Silicone Spray" that i keep eyeballing everytime i think about my nitro fuel. Ingredients (listed by CAS #) are propane, 2-Methylpropane, heptane and (not listed by CAS#) polydimethylsiloxane. PDMS is the same thing in Armor All and i picked this spray up at my local hardware store.


Its not the exact can, but close enough. The 4oz spray can is 110B

(in reply to downunder)
       Post #: 3

RE: silicon anti-foaming agent - 9/13/2004 11:05:53 PM   
downunder



Posts: 3114
Joined: 10/10/2002
From: Adelaide, AUSTRALIA
Status: offline 		I'd say it's definitely worth a try and if it's like Armor All then you only need the tiniest amount in a gallon of fuel. Shake the drum until it's foaming like crazy then give a very quick spray over the opening and see if the foam instantly disappears.

(in reply to geofferama)
       Post #: 4

RE: silicon anti-foaming agent - 9/14/2004 12:36:09 PM   
Fuelman


 

Posts: 1009
Joined: 12/31/2001
From: Jordan, NY, USA
Status: offline 		Carefull !
Too much silicone anything in the fuel will cause deposits on the glowplug with a possible degrading of plug life or performance or reliability.
A drop or two is the maximum amount I would recommend.


_____________________________

Fuelman
Cooper Fuels LLC

(in reply to downunder)
       Post #: 5

RE: silicon anti-foaming agent - 9/14/2004 3:55:07 PM   
geofferama


 

Posts: 280
Joined: 7/10/2004
From: Ginsburg, MD, USA
Status: offline 		I'll give it a try on some fuel in my fuel bottle. I'm using O'Donnell 20% (which I've noticed doesn't have its oil content listed, but I've read as being 16%) and I really should switch to something with a higher oil content. I ran some Monster Brew that a friend had and at the same settings the engine was running much much richer.


I gave the Ke's a very short spritz. 290cc's of fuel in my 500cc fuel bottle and even with vigorous shaking, the foam only rises up to the 300cc mark. I never tried Armor All before so is this Normal/Bad/God Help Me?

(in reply to downunder)
       Post #: 6

RE: silicon anti-foaming agent - 9/30/2004 4:14:48 AM   
rslstft


 

Posts: 178
Joined: 5/1/2002
From: Tustin, CA, USA
Status: offline 		I've been mixing my own fuels (mostly 15% and 30% nitro with 18-20% oil) for a little over 3 years now and quit using any "anti-foaming" additive about a year and half ago and never noticed any difference in engine response and didn't change any of the needle settings at all. I have 7 four strokes and 4 two strokes and they all run the same without the Armor All (which I used to use) added. So, I guess I'm not even sure anything is need to prevent foaming. Next time you mix some fuel, before you add the anti-foamer, shake the bottle and watch how much it foams - not much if at all! Maybe it has something to do with the brand of oil used?? I have always used Klotz oil and some of my engines have more that 10 gallons through them.

Russ

(in reply to geofferama)
       Post #: 7

RE: silicon anti-foaming agent - 10/4/2004 11:23:19 PM   
XJet


 

Posts: 3215
Joined: 3/31/2003
From: Tokoroa, NEW ZEALAND
Status: offline 		Yes, the brand/type of oil can have a huge effect on foaming.

Just last week I was helping another flier set up a new 40-sized trainer with a TT46 in it.

We decided to run the engine in by putting a couple of tanks of fuel through it on the ground so we used some of the break-in fuel I made up for my own engines. This fuel has a fair bit of castor oil in it and a little Coolpower blue.

After about a minute's running there were quite a few very fine bubbles streaming up the fuel line into the fuel-filter. They were collecting there so that if you throttled back and then opened up again, the engine would quite because it would suck the big reservoir of air that had collected in the filter body.

Obviously this was no good for flying so we replaced the clunk line and all the external lines -- but that didn't change anything.

We messed around checking that the tank was isolated from vibration as much as possible -- but that didn't help either.

Finally (on a hunch and after about 15 minute's running-in) we switched to straight CoolPower blue and the problem went away.

Obviously the castor content of the fuel used for running in was contributing significantly to the foaming problem.

< Message edited by XJet -- 10/4/2004 11:24:20 PM >

(in reply to rslstft)
       Post #: 8

RE: silicon anti-foaming agent - 10/4/2004 11:30:01 PM   
Woody 51



Posts: 1156
Joined: 6/21/2003
From: GeelongVictoria, AUSTRALIA
Status: offline 		But what causes the foaming?
I have been thought this excercise before with novices and usually find that an out of balance prop is one of the most common root causes.
Another is having a tank that is not properly insulated from the model with foam rubber etc.
Adding silicone covers the symptoms, but does not solve the problem.

_____________________________

A crash keeps one's opinion of one's flying ability, in perspective.

(in reply to XJet)
       Post #: 9

RE: silicon anti-foaming agent - 10/5/2004 12:38:39 PM   
Fuelman


 

Posts: 1009
Joined: 12/31/2001
From: Jordan, NY, USA
Status: offline 		Oil does make a difference. Castor oil will tend to foam easier and the bubbles last longer than any synthetic oils I know of. Some companies that sell oils suitable for making fuel with have a anti-foam agert blended in.
Ballanced props, padded tanks, good lines all contribute to minimizing foaming or air in the line issues


_____________________________

Fuelman
Cooper Fuels LLC

(in reply to Woody 51)
       Post #: 10

RE: silicon anti-foaming agent - 10/29/2004 9:41:40 PM   
Justrace


 

Posts: 4
Joined: 10/29/2004
From: Coral Springs, FL, USA
Status: offline 		The synthetic oil from Morgan has antifoam properties. That's the green color oil.

http://www.morganfuel.com/homebrew.htm

(in reply to Fuelman)
       Post #: 11

RE: silicon anti-foaming agent - 10/30/2004 9:12:32 AM   
geofferama


 

Posts: 280
Joined: 7/10/2004
From: Ginsburg, MD, USA
Status: offline
quote:

ORIGINAL: Woody 51

But what causes the foaming?
I have been thought this excercise before with novices and usually find that an out of balance prop is one of the most common root causes.
Another is having a tank that is not properly insulated from the model with foam rubber etc.
Adding silicone covers the symptoms, but does not solve the problem.


I'm actually kindof surprised to see this thread went for so long even w/out some newbie resurrecting it. I was asking about silicon additives b/c I've got a nitro truck and they tend to bounce around. That doesn't even account for the non-existant vibration insulation. But as far as planes and heli's go you're mostly right, but that doesn't mean you should cross it off your trouble-shooting checklist.

_____________________________

Ninja Jeopardy!
http://snaxor.com/snaxor/flash/ninja/ninja.htm

(in reply to Woody 51)
       Post #: 12

RE: silicon anti-foaming agent - 10/30/2004 5:17:27 PM   
downunder



Posts: 3114
Joined: 10/10/2002
From: Adelaide, AUSTRALIA
Status: offline 		What the silicon does is reduce the surface tension of the fuel so large bubbles (foam) can't form from vibration. You can't entirely eliminate bubbles because you can't eliminate surface tension.

(in reply to geofferama)
       Post #: 13

RE: silicon anti-foaming agent - 11/28/2004 7:30:16 AM   
PhilNZ



Posts: 27
Joined: 8/9/2004
From: BlenheimMarlborough, NEW ZEALAND
Status: offline 		Hi,
Ok I have just given my Fuel a damn good shaking and the amount of bubbles / foam was so small it and it settled within a few seconds. I am sure that I gave it 3 to 4 times more shaking that it would get in the air even doing full on rolls and loops..

Container used was a 2 litre with 500 mls of New fuel, bubble rise / foam was about 1 to 2 mils
and settled by the time i went to measure the rise ..

Is it advisable to add silicon to methanol ?

This mix is as follows

17 % Pressed castor oil
3 % Acetone
10 % Nitro
70% Methanol

Phil

(in reply to downunder)
       Post #: 14

RE: silicon anti-foaming agent - 11/28/2004 7:47:17 AM   
XJet


 

Posts: 3215
Joined: 3/31/2003
From: Tokoroa, NEW ZEALAND
Status: offline
quote:

ORIGINAL: PhilNZ
This mix is as follows

17 % Pressed castor oil
3 % Acetone
10 % Nitro
70% Methanol


What's the acetone for?

The only time I ever used acetone was when I was trying to get some Castrol R to dissolve in methanol -- and it wasn't partcularly successful.

I have never used it since and everything seems to work sweet with pure castor, or Klotz or Coolpower.

(in reply to PhilNZ)
       Post #: 15

RE: silicon anti-foaming agent - 11/28/2004 8:00:43 AM   
PhilNZ



Posts: 27
Joined: 8/9/2004
From: BlenheimMarlborough, NEW ZEALAND
Status: offline 		Hi XJet,
Ok the acetone does 5 things in a 2 stroke
and 6 things in a 4 stroke.

1/ Its helps stop the methanol absorbing moisture

2/ Helps burn some of the Oil

3/ Helps in the mixing of the oil into the methanol.

4/ Will increase the power slightly

5/ Helps keep the varnish out of engines also

6/ Stops kick back in a 4 stroke ( I can't confirm this but others have )

Also Castrol R and R2 should not be used in RC engines as it is not designed to mix with methanol.

Phillip

(in reply to XJet)
       Post #: 16