RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (Full Version)

All Forums >> [RC Airplanes] >> RC Flight Simulator Software >> Ikarus AeroFly Pro and Aerofly Pro Deluxe



Message

Doc. insane -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (8/5/2005 3:22:19 PM)

Malasian Flyer,

Normally you can't compare a 35% extra with a 40% extra, but this Knol extra flies just like it. Although you'll never have the same power unless you put a DA100 with pipes in front, but than the airframe will lose strength. The votec flies realistic, when it comes to flying a 40% in general, but the real Votec flies a bit different.

Fun_fly_3D,

You can set your rates in afpd next to the channel. You can assign a channel by just clicking on it.



MalaysianFlyer -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (8/5/2005 3:36:21 PM)

Maarten,

Thanks, I am debating between the Votec and the Knol Extra and the Composite Arf Extra. Not easy making a decision. THanks again for your feedback



MalaysianFlyer -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (8/5/2005 3:38:49 PM)

By the way, are you making the Knol extra for AFPD??



Doc. insane -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (8/23/2005 11:48:46 AM)

No, but I'm planning to make one this winter, when the weather is to bad to fly. Goodluck with your choice. :-)



davide.pasq -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (8/23/2005 3:33:41 PM)

hi doc,
can you send me that pdf sheet with 3d?
davide.pasq@alice.it
thank you



MalaysianFlyer -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (8/23/2005 4:24:47 PM)

Maarten, unfortunately the choice is also governed by my bank balance [:D][:D]

Looking forward to your extra, the Votec is currently my favourite plane on AFPD



RearViewMirror6 -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (8/23/2005 9:06:27 PM)

Maarten, What kind of servos do you have on this plane? the extrema.
quote:

ORIGINAL: Doc. insane

On my real shockflyer I use a Typhoon 6 3D engine with tsunami 10 regulator and an apc 8-3.8 prop. with a 720mah 3 cell lipopack. This gives me a total flightweight of 215 grams.
I have as much deflection as possible on all surfaces. My CG is at 7 cm from the leading edge. ( I'm talking about the IKARUS extrema shockflyer) This is the way I fly the extrema shockflyer from IKARUS.




harryw13 -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (9/1/2005 2:18:39 PM)

Maarten,
What is your setup for IMAC flying?
Thanks



jrjohn -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (9/21/2005 4:05:41 PM)

I dont' understed and how to change the center of ballance on AFPD, there seem to be three areas where you can enter numbers. Is there a way to change the ballance by dragging the center of ballance line that appears on the fus?

If anybody has the parameters to make the EF Yak 54 fly realistic, I'd really appreciate some help setting mine up

john



davide.pasq -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (9/21/2005 5:59:02 PM)

yes, there are three spaces for enter your cg because he is on the x, y and z axes. the firs one is for front-back location



jrjohn -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (9/21/2005 6:03:29 PM)


quote:

ORIGINAL: davide.pasq

yes, there are three spaces for enter your cg because he is on the x, y and z axes. the firs one is for front-back location


I'm not sure I understand that, could you explain it a little better please

John



davide.pasq -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (9/21/2005 6:15:13 PM)

ok, sorry for my english, I'm an italian guy!
for change cg on afpd:
- select edit from main menu
- create a new aircaft (if you are using an original one)
- select fusolage from the edit menu
- on the bottom right corner there are a few bottoms: select the cg one
- there are 3 spaces for enter the position of the cg, the first one is whiti is regarding you, it change the cg position from the tail to the nose an vice versa
- the other two space can be left white
- select save from the menu
- select exit

if you don't understand something I wrote, tell me!



jrjohn -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (9/21/2005 7:20:15 PM)


quote:

ORIGINAL: davide.pasq

ok, sorry for my english, I'm an italian guy!
for change cg on afpd:
- select edit from main menu
- create a new aircaft (if you are using an original one)
- select fusolage from the edit menu
- on the bottom right corner there are a few bottoms: select the cg one
- there are 3 spaces for enter the position of the cg, the first one is whiti is regarding you, it change the cg position from the tail to the nose an vice versa
- the other two space can be left white
- select save from the menu
- select exit

if you don't understand something I wrote, tell me!


perfect!

thank you

John



davide.pasq -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (9/22/2005 12:20:54 PM)

you're welcome!



jrjohn -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/8/2005 3:57:26 PM)

Doc, I downloaded your Yak 54 EF 3D, It doesn't seem as realistic as maybe it could be. Can you give me your specs so I can change the setup. And, where do I find information on how to understand and change the planes myself.........thank you

John



3wExtra -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/13/2005 5:09:01 AM)

I need help Please!

I have afpd18021.exe installed and still it will not discover my Multiplex Royal evo 12.
What can i do. I used to have a JR and it always worked.
the error says that AFD found the usb cable, but not the TX
thanks!



bpryor -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/13/2005 5:34:12 AM)


quote:

ORIGINAL: 3wExtra

I need help Please!

I have afpd18021.exe installed and still it will not discover my Multiplex Royal evo 12.
What can i do. I used to have a JR and it always worked.
the error says that AFD found the usb cable, but not the TX
thanks!


Do you have it set to PPM, not PCM. I can't remember if it just doesn't work if it's on PCM, or tells you the transmitter's not found. It's the only thing I can think of.



3wExtra -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/13/2005 9:37:02 PM)

Multiplex does not have PCM



bpryor -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/13/2005 10:26:32 PM)

Well, I guess that isn't it then. [:)] PM mglavin, a moderator here on RCU. I know he flies Multiplex and uses AFPD, but I'm not sure if he uses the Multiplex on the sim.



3wExtra -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/15/2005 8:12:28 AM)

Please can someone HELP with my issue?[sm=crying.gif] I can not get AFD to pick up my TX which is a multiplex RE 12.
thanks
Astolfo



bpryor -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/15/2005 4:17:37 PM)

quote:

ORIGINAL: 3wExtra

Please can someone HELP with my issue?[sm=crying.gif] I can not get AFD to pick up my TX which is a multiplex RE 12.
thanks
Astolfo



Did you write mglavin as I suggested and ask him? Did you call or write AFP tech support? That seems like your best bet if mglavin coulcn't help you.



3wExtra -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/31/2005 9:41:55 PM)

I thouth that this was the official support forum.
I called Ikarus-USA in FL and no answer.
who else can help on this....
thanks



bpryor -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (10/31/2005 11:51:28 PM)


quote:

ORIGINAL: 3wExtra

I thouth that this was the official support forum.
I called Ikarus-USA in FL and no answer.
who else can help on this....
thanks


Well, I don't know why I'm bothering, but for the third time, did you write mglavin and ask him?



3wExtra -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (11/1/2005 12:14:10 AM)

Yes i pmed him and he said that he was ging to get back... i am still waiting



bpryor -> RE: Ask Maarten DeMoor - Setting Up AFP(D) To The Max (11/1/2005 12:32:24 AM)


quote:

ORIGINAL: 3wExtra

Yes i pmed him and he said that he was ging to get back... i am still waiting


Good, I know he is busy but usually he's good about responding. If it's been awhile, write him again. Also, FYI, this forum is authorized by Ikarus, but is not run by them, it is run by OMP(Ohio Model Products). If you really want official help you need to call or write Ikarus. I can't believe they haven't gotten back to you, they were very responsive when I had a problem. Here's a direct e-mail address to one of their support reps: Fred Boyce - boyce@ikarus-usa.com



Page: <<   < prev  4 5 6 7 8 [9] 10 11 12 13   next >   >>  

Valid CSS!




SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.
0.328125