orX-cellerator cluch  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       

All Forums >> RC Cars, Buggies, Trucks, Tanks and more >> RC Nitro Stadium Trucks >> orX-cellerator cluch
Page: [1]

Login
Message << Older Topic   Newer Topic >>
orX-cellerator cluch - 2/25/2005 8:00:20 PM   
yznaction



Posts: 124
Joined: 1/3/2005
From: south pasadena, CA, USA
Status: offline 		Ive got an xtm nitro x-cellerator that works fine. The motor pulls great but the clutch slips so bad. The moter revs out but it barley gets up to speed. My friend advised me to pull apart the clutch and ruff up the pads and bell. I plan to but first want to know if anybody else has had problems thier clutch.

_____________________________

Yzn
       Post #: 1

RE: orX-cellerator cluch - 2/25/2005 11:34:27 PM   
kool_kid


 

Posts: 46
Joined: 12/27/2004
From: Winnipeg, MB, CANADA
Status: offline 		It's just slipping to much all you have to do (correct me if im wrong) is on the spur gear tighten that little nut a bit and u should be fine or there could be something wrong with the clutch but thats my opinion and im probably wrong the only other reason it would be slipping likr that is if you (or someone else) spilt after run oil or fuel on the clutch bell because it has happend to me before but i caught it quck enough to stop it from goin onside the clutch bell.


_____________________________

My truck:
Kyosho Ultima ST Racing Sports GP

(in reply to yznaction)
       Post #: 2

RE: orX-cellerator cluch - 2/26/2005 12:15:26 AM   
YZF Desert



Posts: 394
Joined: 11/4/2004
From: glendale, CA, USA
Status: offline 		its not his slipper clutch that is loose its the clutch shoes that arent grabbing the clutch bell

(in reply to kool_kid)
       Post #: 3

RE: orX-cellerator cluch - 2/26/2005 5:23:15 AM   
ThunderbirdJunkie



Posts: 11874
Joined: 7/25/2004
From: Mason, OH, USA
Status: offline 		you SURE it's the clutch shoes/bell? it might be your diff loosening up.
ball differentials shouldn't be in RTR's:| too many people DONT read the instructions.

_____________________________

Some people can mess up an anvil with a rubber hammer

(in reply to YZF Desert)
       Post #: 4

RE: orX-cellerator cluch - 2/26/2005 3:45:37 PM   
ICrashThings



Posts: 6402
Joined: 1/11/2004
From: Abingdon, MD, USA
Status: offline
quote:

ORIGINAL: ThunderbirdJunkie

you SURE it's the clutch shoes/bell? it might be your diff loosening up.
ball differentials shouldn't be in RTR's:| too many people DONT read the instructions.

ball diffs should be in everything...unless you want to drive a cheap POS. :\

_____________________________

lol $300 Radio? Me controlling it? rofl...

(in reply to ThunderbirdJunkie)
       Post #: 5

RE: orX-cellerator cluch - 2/26/2005 5:19:49 PM   
YZF Desert



Posts: 394
Joined: 11/4/2004
From: glendale, CA, USA
Status: offline 		i held his truck and gave it some throttle to see if the slipper clutch was loose but the slipper clutch was tight and the diff. didnt slip any so im guessing its the shoes, also does the x-c use a ball diff.

(in reply to ICrashThings)
       Post #: 6

RE: orX-cellerator cluch - 2/26/2005 6:58:46 PM   
yznaction



Posts: 124
Joined: 1/3/2005
From: south pasadena, CA, USA
Status: offline 		yea, it uses a diff ball system. im gonna take it apart and have a look at it and get back to you guys.

_____________________________

Yzn

(in reply to YZF Desert)
       Post #: 7

RE: orX-cellerator cluch - 2/26/2005 8:37:59 PM   
ThunderbirdJunkie



Posts: 11874
Joined: 7/25/2004
From: Mason, OH, USA
Status: offline
quote:

ORIGINAL: ICrashThings

quote:

ORIGINAL: ThunderbirdJunkie

you SURE it's the clutch shoes/bell? it might be your diff loosening up.
ball differentials shouldn't be in RTR's:| too many people DONT read the instructions.

ball diffs should be in everything...unless you want to drive a cheap POS. :\


I wouldn't call an XRAY XB8 a cheap pos, and it has THREE gear diffs:P
ball diffs are great for people that know what they're doing, but imo not for newbies.
and yes, the XC uses a ball diff.

_____________________________

Some people can mess up an anvil with a rubber hammer

(in reply to ICrashThings)
       Post #: 8

Page:   [1]
All Forums >> RC Cars, Buggies, Trucks, Tanks and more >> RC Nitro Stadium Trucks >> orX-cellerator cluch
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.517RCU4