91 FZ needle settings    Gallery
View related threads: (in this forum | in all forums)

Logged in as Guest



Users viewing this topic: none
    Search This Thread  
 
Printable Version

All Forums >> Glow Engines, Gas Engines, Fuel & Mfg Support Forums >> Engine Manufacturers Direct Support Forum >> YS Engines Support >> 91 FZ needle settings
Page: [1]

Tower Hobbies Get Coupon Codes Brands  
Login
Message << Older Topic   Newer Topic >>
91 FZ needle settings - 5/19/2005 7:41 PM   
beavertail



Posts: 713
Score: 100
Joined: 12/2/2002
Last Login: 4/5/2008
From: SOUTH, TX, USA
Status: offline 		Dave, I cant find my manual and ran my engine as it came back from repair at YS, but I cant get it to idle down, it stays high, around 3000 and then dies as I close the throttle.
Can you tell me what high and low needle settings should be as a rough start point.

Thanks

Joey

_____________________________

Hows my flying???
Call 1-800-EAT-(Censored by Moderator)

Hide Signatures
       Post #: 1

RE: 91 FZ needle settings - 5/19/2005 8:47 PM   
Dave Shadel


 

Posts: 5408
Score: 100
Joined: 4/9/2002
Last Login: 4/16/2009
From: Gardnerville, NV, USA
Status: offline 		Go to the website and follow the instructions www.ysperformance.com

I suspect the regulator and idle are both too lean.

Hide Signatures

(in reply to beavertail)
       Post #: 2

RE: 91 FZ needle settings - 5/27/2005 7:36 PM   
beavertail



Posts: 713
Score: 100
Joined: 12/2/2002
Last Login: 4/5/2008
From: SOUTH, TX, USA
Status: offline 		Dave, I just pulled the valve cover off, And there is NO tappet clearance at any time of the cycle. I now suspect that this has been the problem all along. My question is that it came from YS service department like this, should it have come back to me in this condition? I feel terrible about trying to run the engine like this, but I didnt think to check the tappet clearance and just expected it to run when I got it back.

Please help,

Joey M

< Message edited by beavertail -- 5/27/2005 7:44 PM >

_____________________________

Hows my flying???
Call 1-800-EAT-(Censored by Moderator)

Hide Signatures

(in reply to Dave Shadel)
       Post #: 3

RE: 91 FZ needle settings - 5/30/2005 5:46 PM   
Dave Shadel


 

Posts: 5408
Score: 100
Joined: 4/9/2002
Last Login: 4/16/2009
From: Gardnerville, NV, USA
Status: offline 		If it really didn't have any valve clearance coming back from service, call them and complain,
LOUDLY!

775-782-4562

Hide Signatures

(in reply to beavertail)
       Post #: 4

RE: 91 FZ needle settings - 5/31/2005 4:44 AM   
beavertail



Posts: 713
Score: 100
Joined: 12/2/2002
Last Login: 4/5/2008
From: SOUTH, TX, USA
Status: offline 		I will try to call, but I cant get anyone to answer, I will try again, I guess Ill send it back in.

I dont want to complain to the guys, I just want the engine to work.

Thanks Dave.


Joey

< Message edited by beavertail -- 5/31/2005 4:47 AM >

_____________________________

Hows my flying???
Call 1-800-EAT-(Censored by Moderator)

Hide Signatures

(in reply to Dave Shadel)
       Post #: 5

RE: 91 FZ needle settings - 6/1/2005 5:35 AM   
Dave Shadel


 

Posts: 5408
Score: 100
Joined: 4/9/2002
Last Login: 4/16/2009
From: Gardnerville, NV, USA
Status: offline 		I don't blame you, keep trying. Today was Monday/Tuesday, and I'm sure the phone was very busy.

Hide Signatures

(in reply to beavertail)
       Post #: 6

Page:   [1]
All Forums >> Glow Engines, Gas Engines, Fuel &amp; Mfg Support Forums >> Engine Manufacturers Direct Support Forum >> YS Engines Support >> 91 FZ needle settings
Page: [1]





Jump to:


 
Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

RC Universe is a service of Internet Brands, Inc. Copyright © 2001-2013.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America


0.852RCU1