5625 Slop  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       


JR NES703 Low Profile Retract Servo
Seller:  Erick Royer
Details:   $75.00   |  9/2/2008   |  Classified Ad
We will rotate YOUR AD in this spot if you select "Forum Featured" when placing or editing your ad!

All Forums >> Radios, Batteries, Clubhouse and more >> RC Radios, Transmitters, Receivers, Servos, gyros >> Radio Manufacturer Direct Support >> Hitec/MultiPlex Radios- Ask Hitec Customer Service >> 5625 Slop
Page: [1]

Login
Message << Older Topic   Newer Topic >>
5625 Slop - 10/13/2002 8:53:22 AM   
Yakdude



Posts: 145
Joined: 5/19/2002
From: Pahrump, NV, USA
Status: offline 		Hello,

I have 2 5625 servos dated march 02 on each elevator of my 1/4 scale Sukhoi. When the servos new about 25 flights ago there was no slop in the shaft whatsoever. Now I would have to consider the slop excessive allowing 1/8 up and down in one elevator and around 3/16 in the other. This is not gear slop. The play is back and forth parallel to the push rod. There is no play 90 degrees to the push rod. I am not sure if the upper bearings are shot or the upper case is worn. Can I send these back to be checked.

Lenny
       Post #: 1

5625 Slop - 10/15/2002 3:07:22 AM   
Glen Merritt


 

Posts: 106
Joined: 6/8/2002
From: San Diego, CA, USA
Status: offline 		Absolutely, send them in to our service department and we will check them out for free.

_____________________________

"It really is harder than it looks"

(in reply to Yakdude)
       Post #: 2

5625 Slop - 10/15/2002 6:55:41 AM   
Yakdude



Posts: 145
Joined: 5/19/2002
From: Pahrump, NV, USA
Status: offline 		Thank you Glen,
Do I need to get an RA # or anything. Can I just send them to your attention.


Lenny

(in reply to Yakdude)
       Post #: 3

5625 Slop - 10/15/2002 8:32:41 PM   
Glen Merritt


 

Posts: 106
Joined: 6/8/2002
From: San Diego, CA, USA
Status: offline 		Howdy Lenny,

Blast over to this page of our web site for all the service information.

http://www.hitecrcd.com/nsupportFS.htm

_____________________________

"It really is harder than it looks"

(in reply to Yakdude)
       Post #: 4

5625 Slop - 10/16/2002 10:05:38 PM   
Robert300XS



Posts: 164
Joined: 7/21/2002
From: San Diego, CA, USA
Status: offline 		Hmm, this must be a "feature" because my hitec digis all have the same problem. I also have that sticker

(in reply to Yakdude)
       Post #: 5

5625 Slop - 10/16/2002 10:35:27 PM   
Glen Merritt


 

Posts: 106
Joined: 6/8/2002
From: San Diego, CA, USA
Status: offline 		Robert,

How about sending your servos back to us at Hitec. Or perhaps if you find that "feature" desirable and want to keep your servos that way, I could make some "special ones" just for you and charge ya a few more ducats for 'em?

Seriously, all metal gear servos will wear faster than plastic ones, creating gear backlash. Based on Lennys description however it might not be gear lash so perhaps in the best interest of safety we should get a chance to fix this for you?

Also, what "sticker" are you referring to?

_____________________________

"It really is harder than it looks"

(in reply to Yakdude)
       Post #: 6

5625 Slop - 10/17/2002 3:19:26 AM   
Robert300XS



Posts: 164
Joined: 7/21/2002
From: San Diego, CA, USA
Status: offline 		The little round sticker that says "Mar 02".

Mine were sloppy after 5 minutes of setting them up... my friend's were sloppy out of the box. I live about 1/2hr away, think if I catch you there, you could take a look while I'm there? It is certainly not geartrain slop, I can sit there and move the output shaft back and forth in a 360 degree movment. I don't think the slop is harming anything, but it will bug me if I try to get more throw out of them.

(in reply to Yakdude)
       Post #: 7

5625 Slop - 10/17/2002 3:41:10 AM   
Glen Merritt


 

Posts: 106
Joined: 6/8/2002
From: San Diego, CA, USA
Status: offline 		Yes Sir we would like very much to see them and if you call first, 1-800-now go rc, ext. 310 make sure I am here first and then come on over.

_____________________________

"It really is harder than it looks"

(in reply to Yakdude)
       Post #: 8

5625 Slop - 10/17/2002 4:26:37 AM   
Robert300XS



Posts: 164
Joined: 7/21/2002
From: San Diego, CA, USA
Status: offline 		ok, thanks!

(in reply to Yakdude)
       Post #: 9

Let us know - 10/22/2002 12:43:31 PM   
Aerosplat



Posts: 707
Joined: 12/11/2001
From: Lawrenceville, GA, USA
Status: offline 		Robert300XS or Glen,
Be sure to report back here with the results of your check-up. I have several Hitec Digitals now.

_____________________________

---- Robert ----
"If you put a big enough engine on it, even a brick will fly. But it will never 3-D"

(in reply to Yakdude)
       Post #: 10

Page:   [1]
All Forums >> Radios, Batteries, Clubhouse and more >> RC Radios, Transmitters, Receivers, Servos, gyros >> Radio Manufacturer Direct Support >> Hitec/MultiPlex Radios- Ask Hitec Customer Service >> 5625 Slop
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.438RCU1