#4 single receiver adjustment  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       


MS Composit Hornet X-CP ARF w/Brushless Motor
Seller:  Erick Royer
Details:   $100.00   |  9/6/2008   |  Classified Ad
We will rotate YOUR AD in this spot if you select "Forum Featured" when placing or editing your ad!

All Forums >> RC Helicopters >> Electric RC Helis >> #4 single receiver adjustment
Page: [1]

Login
Message << Older Topic   Newer Topic >>
#4 single receiver adjustment - 8/29/2005 8:06:28 PM   
chris6414



Posts: 600
Joined: 12/23/2004
From: Warminster , PA, USA
Status: offline 		Does anyone know what that one little adjustment is on the Walkera Dragonfly receiver is for. I don't want to experiment until I am sure what effect I get. I've searched and none seems to be sure. Thanks in advance
       Post #: 1

RE: #4 single receiver adjustment - 8/29/2005 11:02:04 PM   
credence


 

Posts: 2518
Joined: 5/19/2005
From: Brampton, ON, CANADA
Status: offline 		Nothing, so far as I can tell. Some claim it makes a very small effect in tail control, but i've never noticed. The screw just spinds endlessly affecting precisely nothing for me

_____________________________

Daniel
True Northern Hobbies, Inc.

(in reply to chris6414)
       Post #: 2

RE: #4 single receiver adjustment - 10/30/2005 11:47:19 AM   
Dolan


 

Posts: 32
Joined: 10/18/2005
From: Polson, MT, USA
Status: offline 		Hello............

Question about "WALKERA HELICOPTERS", Yes, I happen to buy one or TWO..."OOPS" (I must be CRAZY!!) And that I am, However I can relate to all of you who are have problems with this HELI'S. I have the DRAGONFLY 35 and the DRAGONFLY 04. These are not my first HELI'S and from my experance I cna tell that the "The New Kid on the BLOCK with HELIS" Will be somewhat comfused because of WALKERA'S lack of Information. The owners Manuals are not translated that good and LACK the vital info for the Begainer. Anyway I'll post the contact info for WALKERA's website.............Here ya go!!

heli@walkera.com
info@walkera.com
http://www.walkera.com

It would be nice if anyone gets a responce to share there INFO with US here on RCUNIVERSE..............Thanks AGAIN!!





(in reply to credence)
       Post #: 3

RE: #4 single receiver adjustment - 10/31/2005 4:38:33 PM   
sportygreg



Posts: 342
Joined: 9/4/2005
From: Dunedin, FL, USA
Status: offline 		As far as I know,the screw is a "tail mixing" adjustment that seems to have little or no effect.I tried to contact Walkera about this but only received gibberish in response.

_____________________________

I hope I'm in heaven a half hour before the devil knows I'm dead!

(in reply to Dolan)
       Post #: 4

RE: #4 single receiver adjustment - 10/31/2005 6:58:00 PM   
chench


 

Posts: 77
Joined: 4/24/2005
From: EdinburghScotland, UNITED KINGDOM
Status: offline 		Apparently thee screw is meant to adjust the gain of the gyro but most people say its useless. Ive had 2 recievers and the first had more gyro effect than the second.

(in reply to sportygreg)
       Post #: 5

RE: #4 single receiver adjustment - 11/16/2005 5:31:30 PM   
stevewright01


 

Posts: 25
Joined: 11/12/2005
From: Nottingham, UNITED KINGDOM
Status: offline 		Hello,

I don't know if anybody out there can help but if you can it would be greatly appreciated.

Playing with my #40 now and had a spectaular crash.

First of all I think the leads from the servo's are connected to the receiver incorrectly - The Helicopter sat on the ground at full power (I have throttle on the right stick) and launched of the ground when I pushed the left stick forward (which should make the helicopter move forward when in the air I believe!) and then came straight back down.

if anybody could tell me which servo leads (there are 3 servos) go into which slots on the reciever that would ge a good start.

I managed to completely knacker the bits around the main rorot blades, one of the main blades, the bar that goes across the helcopter that the canopy clips into, and I have found that the rear motor sticks - all in all a bit of a mess so if any body could supply these parts that would be great.


Cheers.

(in reply to chench)
       Post #: 6

Page:   [1]
All Forums >> RC Helicopters >> Electric RC Helis >> #4 single receiver adjustment
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.578RCU1