NX26 problem...  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       


Associated MGT 8.0 - RTR
Seller:  ScottInMichigan
Details:   $450.00   |  10/6/2008   |  Classified Ad
We will rotate YOUR AD in this spot if you select "Forum Featured" when placing or editing your ad!

All Forums >> RC Cars, Buggies, Trucks, Tanks and more >> CEN Racing >> NX26 problem...
Page: [1]

Login
Message << Older Topic   Newer Topic >>
NX26 problem... - 5/16/2006 3:13:17 AM   
Zonk


 

Posts: 183
Joined: 4/10/2006
From: Sydney, AUSTRALIA
Status: offline 		Hey I've just put my 4th tank through my Matrix and I took her to the local BMX track today to put the last 2 tanks through it before I started leaning her out. She has always started fairly easily and this morning was no exception... except.. it started stalling after 5-20 secs, often before I even touched the throttle. Thinking the plug had died I replaced it with a brand new one. That did not help. So I reset the needles to factory defaults, again the problem wouldn't go away. I slightly increased the idle, then richened the mid and low end, no good, leaned it out as well and it still dies. Getting a little frustrated (friend is up and running with his Swift thing, makes me annoyed I can't join him). I then replaced the fuel tubing, cleaned the mid range needle as well. Problem is still there. (Using a Cen Rotostarter, then my mates Ofna Starter Box, to no avail).
Car starts up, runs well, then 10-20 secs later it stalls. It has fuel flowing, no blockages either, really am baffled. Sadly I gave up and came home, want to try again tomorow.

Can anyone lend me some clues?

Thankyou in advance.

-Mike

_____________________________

Hyper 8 Pro, Hyper 7 PCR, Cen Matrix Pro, Hobao GPX4 Pro, Thunder Tiger TS4N, LSP Pro R, Hobao Hyper ST Pro, HPI Baja +more.
       Post #: 1

RE: NX26 problem... - 5/16/2006 8:19:52 AM   
Zonk


 

Posts: 183
Joined: 4/10/2006
From: Sydney, AUSTRALIA
Status: offline 		Anyone? 2morow is my last day off before I do 8 days straight, really want to get it running:P


Baffling/annoying problem, every dam needle setting in the universe, starts, runs ok, 10 secs later stalls. Fuel is flowing, no air bubbles, normally retarts after a stall as well. Idling nice n quick. Leaving the glow starter in does not help.


HELP ME PLEASE!!!

< Message edited by Zonk -- 5/16/2006 8:20:53 AM >

_____________________________

Hyper 8 Pro, Hyper 7 PCR, Cen Matrix Pro, Hobao GPX4 Pro, Thunder Tiger TS4N, LSP Pro R, Hobao Hyper ST Pro, HPI Baja +more.

(in reply to Zonk)
       Post #: 2

RE: NX26 problem... - 5/17/2006 12:36:52 AM   
bjburton


 

Posts: 2
Joined: 5/7/2006
From: sikeston, MO, USA
Status: offline 		check your fuel tank for leaks around the seam.mine did the same thing after i replaced the tank it ran fine

(in reply to Zonk)
       Post #: 3

RE: NX26 problem... - 5/17/2006 1:22:18 AM   
craigb



Posts: 244
Joined: 7/25/2003
From: birmingham, UNITED KINGDOM
Status: offline 		eeerm... very strange!

... try some of your mates fuel... might help.

Is it bogging then stalling or reving up and stalling?

_____________________________

owner of the first and only known (to me) OS fourstroke powered CEN Fun Factor MT2

(in reply to bjburton)
       Post #: 4

RE: NX26 problem... - 5/17/2006 1:58:15 AM   
Zonk


 

Posts: 183
Joined: 4/10/2006
From: Sydney, AUSTRALIA
Status: offline 		Thanks for the replies.
The fuel tank is sealed, there are no airbubbles escaping and the fuel I'm using powers my old Inferno DX without a hiccup. Also use it in my Nitro Tourer. Its a 20% compertition mix.

_____________________________

Hyper 8 Pro, Hyper 7 PCR, Cen Matrix Pro, Hobao GPX4 Pro, Thunder Tiger TS4N, LSP Pro R, Hobao Hyper ST Pro, HPI Baja +more.

(in reply to craigb)
       Post #: 5

RE: NX26 problem... - 5/17/2006 2:26:59 AM   
FJ40


 

Posts: 21
Joined: 4/22/2006
From: Montague, MI, USA
Status: offline 		Mine did the same I would just have to let it warm up for about a whole minute and then I would pick it up and rev it up and it would be fine. Just cold blooded I thoght. Now it is just a routine.

(in reply to Zonk)
       Post #: 6

Page:   [1]
All Forums >> RC Cars, Buggies, Trucks, Tanks and more >> CEN Racing >> NX26 problem...
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.406RCU1