Ys 140 L  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       


F3A pattern composite Sickle kit - ARF
Seller:  bondtasha
Details:   $1,100.00   |  12/25/2008   |  Classified Ad
We will rotate YOUR AD in this spot if you select "Forum Featured" when placing or editing your ad!

All Forums >> RC Airplanes >> Pattern Flying >> Ys 140 L
Page: [1]

Login
Message << Older Topic   Newer Topic >>
Ys 140 L - 12/30/2002 9:26:38 PM   
aleo


 

Posts: 14
Joined: 12/15/2002
From: oranjestad, ARUBA
Status: offline 		I HAVE A BRAND NEW 140 YS L ON MY NEW FOCUS.


SEEMS LIKE EVERYTHING IS OK WITH THE MOTOR.(HIGH AND LOW SPEED).

BUT AFTER FLYING FOR ABOUT 5 MINUTES EACH FLITE I GET A DEAD STICK. tILL NOW A MANAGE TO LAND THE PLANE WITHOUT ANY PROBLEM.

THANKS,

LUIS

_____________________________

luis
       Post #: 1

Ys 140 L - 12/30/2002 9:50:27 PM   
Pattern freak



Posts: 123
Joined: 10/4/2002
From: Oranjestad, ARUBA
Status: online 		Luis,Dave Shadel can help you.If you go to the ENGINES Forum(it`s on the top of the screen) then go to YS engine support,you can post and they will help you allot bather.Corda bin bula diahuebs,nada di bebemento mayan .

_____________________________

G.S.Winklaar.2nd Place is the first loser.
www.arubarc.com

(in reply to aleo)
       Post #: 2

many options - 12/31/2002 1:59:18 AM   
Troy Newman


 

Posts: 2429
Joined: 12/30/2001
From: Goodyear, AZ, USA
Status: offline 		Glow plug? Use the OS #F or the YS plug

Also is the motor mount moving.....? If it is the pushrod is closing the carb and killing it. I fought this one time and the motor mount was just loose a little like less than 1/16" total twist side to to side.....

is the throttle linkage flexing? A little movement can cause the barrel to close and kill it.

Is the idle set too low....? SHould be set at 2000rpm.

Throttle servo bad? I don't use cheapy standard servos on the throttle. I use a Ball Bearing corelessss servo like the JR 3421 or even the 4131 or 8101 in the standard sizes....Throttle is just as important as ailerons or Elevator.

Next is fuel tank....everything OK?

Is it getting hot?

Lots of options.....I have dealt with them all over the years. Usually I find its something I'm doing and not the fault of the motor....Had a motor mount that came loose by pulling the threads out of the blind nut. Everything looked tight and neat...but had to remove the motor and the mount and found the blind nuts had failed on 2 or the 3 bolts. The motor was not moving much but a little and it caused problems at idle.


Troy Newman

< Message edited by tnewman -- Jan 1 2003 11:50PM >

(in reply to aleo)
       Post #: 3

Ys 140 L - 12/31/2002 8:51:58 AM   
patternrules


 

Posts: 548
Joined: 7/28/2002
From: Nineveh, IN, USA
Status: offline 		Some of the L's had a plunger that was an experiment that didn't work, if it has a big plunger about 3/8" to 7/16" it is too big and a replacement about 3/16" will fix, I had that problem it took a year to find a freind told me about it and it run great after that.

Steve Maxwell

(in reply to aleo)
       Post #: 4

Page:   [1]
All Forums >> RC Airplanes >> Pattern Flying >> Ys 140 L
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.360RCU4