SE V2 vs. V1 and spektrum receivers  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       



All Forums >> RC Helicopters >> Electric RC Helis >> T-Rex heli >> SE V2 vs. V1 and spektrum receivers
Page: [1]

Login
Message << Older Topic   Newer Topic >>
SE V2 vs. V1 and spektrum receivers - 1/13/2007 11:18:08 PM   
ZX11


 

Posts: 65
Joined: 1/2/2007
From: Omaha, NE, USA
Status: offline 		I am getting a 450 SE on wednesday from my LHS. How do I tell if it is a V2 (that i hear has updates) and not a V1? Do they even have V1 kits still on the market?

On a different note, I am looking at buying a spektrum 6100 receiver for my DX7 radio to run on the Trex. Do I need to buy the smaller parkflyer receiver? The stock 7 channel receiver (7000?) looks pretty small but it is bigger than the 6100. Can the Trex handle the bigger stock receiver with its two components?
       Post #: 1

RE: SE V2 vs. V1 and spektrum receivers - 1/13/2007 11:36:39 PM   
don_87


 

Posts: 223
Joined: 12/26/2005
From: Markleysburg, PA, USA
Status: offline 		Yes, there are still version 1's out there. And yes, you can use the 7000 rx on the trex. I have it on my Trex 450HDE. I put the main rx on the bottom rear, and the telebee gyro in front of it, the small rx is on the left side of my heli pretty much beside the motor.

(in reply to ZX11)
       Post #: 2

RE: SE V2 vs. V1 and spektrum receivers - 1/14/2007 8:51:54 AM   
robmoney



Posts: 323
Joined: 11/22/2006
From: Hurst, TX, USA
Status: offline 		I use the AR6000 in mine it is much smaller, fits nice! AR6000 / AR6100 both have over 5000 feet range on the ground, so this is not a problem...

The tail rotor hub is a main thing from what I understand V1 vs. V2...

The tail rotor center hub with the set screw that holds it to the shaft is silver. The V2 has two grooves that run around each end of this hub, V1 is a smooth hub with no grooves...

The tail shaft gear is aluminum as well, V1 was a black plastic gear for the belt...

Rob

_____________________________

If I could only stop modding my heli???

(in reply to don_87)
       Post #: 3

RE: SE V2 vs. V1 and spektrum receivers - 1/14/2007 9:21:21 PM   
ZX11


 

Posts: 65
Joined: 1/2/2007
From: Omaha, NE, USA
Status: offline 		Thanks for the help. I will check the kits for the aluminum drive gear on the tail shaft to get the V2. That is just incase the box doesn't have a label with the info.

I will have to check the distance i am looking to fly. Sounds like i can use either rx. I was looking to bug the neighbors by flying thru their yard but they are on a different acreage and a good field away (1000ft?). My CX couldn't make the trip unless it had a tail wind both ways

(in reply to robmoney)
       Post #: 4

RE: SE V2 vs. V1 and spektrum receivers - 1/15/2007 4:11:34 AM   
robmoney



Posts: 323
Joined: 11/22/2006
From: Hurst, TX, USA
Status: offline 		It would get so small you would lose orientation anyways...

_____________________________

If I could only stop modding my heli???

(in reply to ZX11)
       Post #: 5

Page:   [1]
All Forums >> RC Helicopters >> Electric RC Helis >> T-Rex heli >> SE V2 vs. V1 and spektrum receivers
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.531RCU1