RE: New Somenized (TM) 69", Yak-54  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       



All Forums >> RC Airplanes >> Giant Scale Aircraft - 3D & Aerobatic >> Quique's Aircraft Support >> RE: New Somenized (TM) 69", Yak-54
Page: <<   < prev  5 6 7 8 9 10 11 [12] 13 14   next >   >>  

Login
Message << Older Topic   Newer Topic >>
RE: New Somenized (TM) 69", Yak-54 - 3/5/2008 5:04:15 AM   
Rezagh


 

Posts: 1734
Joined: 6/10/2004
From: Rancho Santa Margarita, CA, USA
Status: offline 		Hi Eric,

Thanks very much for your kind words and support. My CG is right at 8 1/2" on the 102". What part of rolling manuever are you interested in? I will be more than happy to help out in any way I can. I have limited flying skills and not much time to improve but I try very hard each time I fly.

Thank you,
Reza

_____________________________

Quique's Aircraft Company

(in reply to husafreak)
       Post #: 276

RE: New Somenized (TM) 69", Yak-54 - 3/5/2008 3:49:26 PM   
pinguecola


 

Posts: 84
Joined: 12/11/2005
From: roma, ITALY
Status: offline 		i would like to thank QQ factory, Quique somenzini itself and Reza.
i sent an email to QQ aircraft and to reza because my landing gear was not fine, and
some days ago i received the replacement landing gear from the italian dealer. i have not had to pay anything.
thank you again, it was really an effective post selling service. these things do not alwais appen, indeed. i feel very happy about my quique yak !!!

ciao a tutti francesco

(in reply to Rezagh)
       Post #: 277

RE: New Somenized (TM) 69", Yak-54 - 3/5/2008 5:51:13 PM   
husafreak


 

Posts: 69
Joined: 12/24/2004
From: , CA, USA
Status: offline 		Well, I can maintain constant rolling maneuvers (like the harrier) in a straight line until I try to bend it into a loop or circle or figure eight and then I end up getting squirilly (sp?) and I have to bail out.

(in reply to pinguecola)
       Post #: 278

RE: New Somenized (TM) 69", Yak-54 - 3/6/2008 4:01:32 PM   
husafreak


 

Posts: 69
Joined: 12/24/2004
From: , CA, USA
Status: offline 		I have the Hyde soft mount for my Ys 110, Is anyone using this product? I am after the quietest possible setup.

(in reply to dmajchrzak)
       Post #: 279

RE: New Somenized (TM) 69", Yak-54 - 3/10/2008 5:23:35 AM   
noahb



Posts: 526
Joined: 1/19/2002
From: Carlsbad, NM, USA
Status: offline 		was wondering the same about the hyde mount and if it would be a good idea to run on here or would hard mounting the YS 1.10s be ok?

(in reply to husafreak)
       Post #: 280

RE: New Somenized (TM) 69", Yak-54 - 3/16/2008 3:08:40 PM   
kf6gub


 

Posts: 197
Joined: 12/31/2002
From: Round Rock, TX, USA
Status: offline 		Anybody mount a "gasser" on the 69"? thx Jim

(in reply to noahb)
       Post #: 281

RE: New Somenized (TM) 69", Yak-54 - 3/16/2008 3:59:59 PM   
octanehuffer



Posts: 663
Joined: 7/15/2006
From: Lakeland, MN, USA
Status: offline 		The planes this size dont fly well enough with a gas engine. A G-20 on this plane will work but you wont get any hover time. Many people have had them on thier Showtimes and Funtana's with the same results. Pattern yes. 3D no.

_____________________________

QQ 86" Evolution, QQ 69" Saito 1.25, QQ 49" 32SX, QQ E-Yak, Funtana 90 Saito 1.20, H9 T-Craft G-26, etc

(in reply to kf6gub)
       Post #: 282

RE: New Somenized (TM) 69", Yak-54 - 3/19/2008 12:42:20 AM   
glasscock


 

Posts: 14
Joined: 4/5/2006
From: Charlotte, NC, USA
Status: offline 		Just ordered Quique's 69" Yak!!! A great addition to the hangar and looks fun to fly. Questions:

For throttle servo, is the JR 2721 necessary, as shown in the manual, or can a less expensive servo be used?

I have two OS 1.20 Four-strokes, one with and one without a pump. What performance can I gain from using an OS 1.20 AX, as opposed to one of the 4-strokes?

Propeller recommendations for above engines? Wood vs. Synth.?

Best place to buy JR servos?

Thanks for any and all input and advice!

DaveG.

(in reply to octanehuffer)
       Post #: 283

RE: New Somenized (TM) 69", Yak-54 - 3/25/2008 11:10:33 PM   
adamiani


 

Posts: 95
Joined: 1/8/2008
From: Boca Raton, FL, USA
Status: offline 		Guys what size spinner are you using with the Yak 69" on the OS 120AX. thank you


_____________________________

Alex & Gabriel Damiani
AMA 898637

(in reply to glasscock)
       Post #: 284

RE: New Somenized (TM) 69", Yak-54 - 3/25/2008 11:36:36 PM   
Brenner


 

Posts: 78
Joined: 7/23/2007
From: Bridgman, MI, USA
Status: offline 		I'm using a 2 1/2" standard shape Tru-Turn anodized red with the slots custom cut to fit the APC 17X6.

(in reply to adamiani)
       Post #: 285

RE: New Somenized (TM) 69", Yak-54 - 3/27/2008 3:00:57 PM   
JohnAV


 

Posts: 1
Joined: 11/5/2003
From: Bristol, TN, USA
Status: offline 		Did not see an answer to the question regarding the use of a Hyde soft mount vs. the hard mount. I’m getting ready to start on my QQ 69" Yak-54 and planning to use a YS110. I have a Hyde mount and was considering using it in place of the hard mount.

(in reply to Brenner)
       Post #: 286

RE: New Somenized (TM) 69", Yak-54 - 3/27/2008 3:45:39 PM   
Rezagh


 

Posts: 1734
Joined: 6/10/2004
From: Rancho Santa Margarita, CA, USA
Status: offline 		Hello John,

There is really no need to use Hyde mount on the YS 1.10. In all of our testing and the plane I fly, the stock mount has been used with no issues what so ever.

Thank you,
Reza
quote:

ORIGINAL: JohnAV

Did not see an answer to the question regarding the use of a Hyde soft mount vs. the hard mount. I’m getting ready to start on my QQ 69" Yak-54 and planning to use a YS110. I have a Hyde mount and was considering using it in place of the hard mount.



_____________________________

Quique's Aircraft Company

(in reply to JohnAV)
       Post #: 287

RE: New Somenized (TM) 69", Yak-54 - 3/27/2008 6:21:40 PM   
adamiani


 

Posts: 95
Joined: 1/8/2008
From: Boca Raton, FL, USA
Status: offline 		Servo City had some great sale last week keep an eye for them I have the same plane and put some HS 5645MG all around and a HS 82 MG for throttle.

Spinner from MPI PRO Spin 3 1/4 best in market @ 1/2 price from Tru Turn with a APC prop 17 x 6

OS 120 AX perfect


_____________________________

Alex & Gabriel Damiani
AMA 898637

(in reply to glasscock)
       Post #: 288

RE: New Somenized (TM) 69", Yak-54 - 3/30/2008 4:36:38 AM   
octanehuffer



Posts: 663
Joined: 7/15/2006
From: Lakeland, MN, USA
Status: offline 		I dont have the plane completed yet but I did weigh everything needed. I have a 5lb digital scale , so I am a bit limited to what I can weigh. My very close weight estimate is 7 lb 5 oz. empty. With a 12oz(?) tank I will be at 8lb 1oz. I had a goal to be at under 8 lb RTF. It will be close. What does everybody else's weigh, and what size it the fuel tank?
Cant wait to fly it.
Adam

_____________________________

QQ 86" Evolution, QQ 69" Saito 1.25, QQ 49" 32SX, QQ E-Yak, Funtana 90 Saito 1.20, H9 T-Craft G-26, etc

(in reply to adamiani)
       Post #: 289

RE: New Somenized (TM) 69", Yak-54 - 4/3/2008 12:06:58 AM   
overbored77


 

Posts: 603
Joined: 4/30/2005