LED Question  
View related threads: (in this forum | in all forums)

Tower Hobbies
Enter up to 4 keywords or Tower stock numbers
Logged in as Guest



Users viewing this topic: none
  Printable Version
       

All Forums >> Radios, Batteries, Clubhouse and more >> RC Radios, Transmitters, Receivers, Servos, gyros >> Radio Manufacturer Direct Support >> Smart-Fly (Quest Engineering) Support Forum >> LED Question
Page: [1]

Login
Message << Older Topic   Newer Topic >>
LED Question - 3/13/2007 3:43:11 PM   
ATCDave



Posts: 30
Joined: 4/23/2004
From: Rindge, NH, USA
Status: offline 		Hi Robert,

I have successfully installed a Power Expander, SuperReg, Ignition Regulator and Ignition Cutoff in my SD Models 30% Yak. All worked perfectly on initial turn on.
Question: Do I disconnect the LED bulb or wire connector to the bulb housing in order to mount the bulb outside the fuselage? A 1/4" hole is too small to pass the receiver end connector through isn't it?
After getting everything installed and working perfectly I feel a little silly being stumped by this, but having an outboard LED showing ignition status is too good of an item to leave undone.

As always thanks Robert for these great products.

Best,

Dave

EDIT: Oops, I just noticed the post further down on this subject...........

< Message edited by ATCDave -- 3/13/2007 3:49:43 PM >

_____________________________

Vector this.....
       Post #: 1

RE: LED Question - 3/13/2007 3:49:44 PM   
rrritchey


 

Posts: 626
Joined: 9/29/2004
From: Phoenix, AZ, USA
Status: offline 		Hi Dave,
The best way to do this is to CAREFULLY take the pins out of the plastic housing. Its really easy BUT do not over bend the plastic flap that holds the pin in. Lift it up just enough to let the pin slide out.
Please let me know if you have any other questions.


_____________________________

Robert Ritchey
Owner, Smart-Fly

(in reply to ATCDave)
       Post #: 2

RE: LED Question - 3/14/2007 3:54:19 PM   
ATCDave



Posts: 30
Joined: 4/23/2004
From: Rindge, NH, USA
Status: offline 		Thanks Robert,


I decided to lengthen the extension to the bulb a bit , so I did what I should have done when I cut the LED wires the first time: fish the wires through the fuse and THEN solder it! (duh). Thanks for your reply though.


Best,

Dave

_____________________________

Vector this.....

(in reply to rrritchey)
       Post #: 3

RE: LED Question - 3/14/2007 3:56:43 PM   
rrritchey


 

Posts: 626
Joined: 9/29/2004
From: Phoenix, AZ, USA
Status: offline 		Hi Dave,
Just so you know in the future, you can lengthen the LED wires by just plugging in a standard servo extension, no soldering.


_____________________________

Robert Ritchey
Owner, Smart-Fly

(in reply to ATCDave)
       Post #: 4

Page:   [1]
All Forums >> Radios, Batteries, Clubhouse and more >> RC Radios, Transmitters, Receivers, Servos, gyros >> Radio Manufacturer Direct Support >> Smart-Fly (Quest Engineering) Support Forum >> LED Question
Page: [1]





Jump to:


Google 



Search | Marketplace | Event Calendar | Local Clubs | Magazine | Product Ratings | New Products | Discussion Forums

Photo Gallery | Member Video Posts | RCU Video Gallery | Instructor Search | Field|Track|Marina Search

Advertisers | Hobby Vendor Resources | Rate Manufacturers | Sign In/Sign Up

SITE MAP!   : :   FORUM RULES

© 2001 - 2007 24-7 RC, LLC, all rights reserved.

Charities we support that also need your help
Yorkie Rescue | Humane Society | ASPCA | Crohn's-Colitis America

Kaango.com Classifieds

0.359RCU1